Looks ugly, a space before a period at the end of a sentence. Remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pull MTD fixes from Brian Norris:
"Two MTD fixes for 4.1:
- readtest: the signal-handling code was clobbering the error codes
we should be handling/reporting in this test, rendering it useless.
Noticed by Coverity.
- the common SPI NOR flash DT binding (merged for 4.1-rc1) is being
revised, so let's change that before 4.1 is minted"
* tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd:
Documentation: dt: mtd: replace "nor-jedec" binding with "jedec, spi-nor"
mtd: readtest: don't clobber error reports
OSA Ethernet hardware is introducing BRIDGEPORT functionality
similar (but not identical) to HiperSockets BRIDGEPORT. This
patch makes HiperSockets BRIDGEPORT related sysfs attributes
and udev events work with OSA hardware too.
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This documents the device tree bindings on the top level of
the Ux500 boards.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds device tree bindings for the ARM Cortex-A5 and
Cortex-A9 Snoop Control Units.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a high pass filter attribute for measurements
(like the existing low pass)
Also add both high and low pass attributes for events.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull tty/serial fixes from Greg KH:
"Here's some TTY and serial driver fixes for reported issues.
All of these have been in linux-next successfully"
* tag 'tty-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
pty: Fix input race when closing
tty/n_gsm.c: fix a memory leak when gsmtty is removed
Revert "serial/amba-pl011: Leave the TX IRQ alone when the UART is not open"
serial: omap: Fix error handling in probe
earlycon: Revert log warnings
Mark "samsung,exynos3250-rtc" compatible as deprecated because it
duplicates the "samsung,s3c6410-rtc". Use "samsung,s3c6410-rtc" on
Exynos3250 and Exynos4415 boards.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Now that the rework to have one sub-node per device in the chip and
system controllers is done, their dedicated compatible can be removed.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Berlin clock documentation was part of the Marvell Berlin SoC
documentation because the Berlin clock configuration was inside the
chip controller. With the recent rework of the chip and system
controller handling (now all sub-devices of the soc and system
controller nodes are registred with simple-mfd, and each device has its
own sub-node), the documentation of the Berlin clock driver can be moved
to the generic clock documentation directory.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Berlin pinctrl documentation was part of the Marvell Berlin SoC
documentation because the Berlin pinctrl configuration was inside the
chip and the system controllers. With the recent rework of the chip and
system controller handling (now an MFD driver registers all sub-devices
of the two soc and system controller nodes and each device has its own
sub-node), the documentation of the Berlin pinctrl driver can be moved
to the generic pinctrl documentation directory.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Berlin reset documentation was part of the Marvell Berlin SoC
documentation because the Berlin reset configuration was inside the chip
controller. With the recent rework of the chip and system controller
handling (now an MFD driver registers all sub-devices of the two soc and
system controller nodes and each device has its own sub-node), the
documentation of the Berlin reset driver can be moved to the generic
reset documentation directory.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
We're moving from a single node for multiple devices to a node with one
sub-node per sub-device, registered by simple-mfd. Update the
documentation to reflect the changes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Because the support of Marvell Berlin SoCs is still a work in progress,
add a statement to explicitly consider our device tree files and
bindings as unstable.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add notes to describe how some SoCs integrate this NAND core a little
differently, and so we define extra compatibility strings and register
resources/names.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
In commit 8ff16cf77c ("Documentation: devicetree: m25p80: add "nor-jedec"
binding"), we added a generic "nor-jedec" binding to catch all
mostly-compatible SPI NOR flash which can be detected via the READ ID
opcode (0x9F). This was discussed and reviewed at the time, however
objections have come up since then as part of this discussion:
http://lkml.kernel.org/g/20150511224646.GJ32500@ld-irv-0074
It seems the parties involved agree that "jedec,spi-nor" does a better
job of capturing the fact that this is SPI-specific, not just any NOR
flash.
This binding was only merged for v4.1-rc1, so it's still OK to change
the naming.
At the same time, let's move the documentation to a better name.
Next up: stop referring to code (drivers/mtd/devices/m25p80.c) from the
documentation.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
STMicrolectronics's STM32 series is a family of Cortex-M
microcontrollers. It is used in various applications, and
proposes a wide range of peripherals.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Simplify the device tree support of the amd-xgbe driver by defining
the PHY-related resources within the ethernet device node. The support
provides backwards compatibility with the original way.
Update the driver version to 1.0.2.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMD XGBE device is intended to work with a specific integrated PHY
and that PHY is not meant to be a standalone PHY for use by other
devices. As such this patch removes the phylib driver and implements
the PHY support in the amd-xgbe driver (the majority of the logic from
the phylib driver is moved into the amd-xgbe driver).
Update the driver version to 1.0.1.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding documentation for nxp,lpc1850-dwmac.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge "RaspberryPi Device Tree changes due for v4.2" from Lee Jones:
* tag 'rpi-dt-for-armsoc-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi:
ARM: bcm2835: dt: Use 0x4 prefix for DMA bus addresses to SDRAM.
ARM: bcm2835: dt: Add the mailbox to the device tree
ARM: bcm2835: dt: Fix i2c0 node name
ARM: bcm2835: dt: Use pinctrl header
ARM: bcm2835: dt: Add header file for pinctrl constants
ARM: bcm2835: dt: Add root properties for Raspberry Pi
ARM: bcm2835: dt: Add vendor prefix for Raspberry Pi
Merge "Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Enable DMA for HSUSB on r8a7790 and r8a7791 SoCs
* Configure the HOME key as wake-up source on kzm9g board
* Use generic names for device nodes on SH Mobile SoCs and boards
* Add "nor-jedec" compatible value to SH Mobile boards
* Add IRQC clock to r8a73a4, r8a779* SoCs
* Remove MSIOF address from r8a7790 and r8a7791 SoCs
* tag 'renesas-dt-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
ARM: shmobile: r8a7791: Enable DMA for HSUSB
ARM: shmobile: r8a7791: add USB-DMAC device nodes
ARM: shmobile: r8a7790: Enable DMA for HSUSB
ARM: shmobile: r8a7790: add USB-DMAC device nodes
ARM: shmobile: kzm9g dts: Configure the HOME key as wake-up source
ARM: shmobile: koelsch dts: Use generic names for device nodes
ARM: shmobile: lager dts: Use generic names for device nodes
ARM: shmobile: bockw dts: Use generic names for device nodes
ARM: shmobile: koelsch dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw dts: Add "nor-jedec" compatible value
ARM: shmobile: lager dts: Add "nor-jedec" compatible value
ARM: shmobile: bockw-reference dts: Add "nor-jedec" compatible value
ARM: shmobile: henninger dts: Add "nor-jedec" compatible value
ARM: shmobile: armadillo800eva dts: Use generic names for device nodes
ARM: shmobile: marzen dts: Use generic names for device nodes
ARM: shmobile: kzm9d dts: Use generic names for device nodes
ARM: shmobile: ape6evm dts: Use generic names for device nodes
ARM: shmobile: sh73a0 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7791 dtsi: Use generic names for device nodes
ARM: shmobile: r8a7790 dtsi: Use generic names for device nodes
...
Merge "Device Tree changes" from Florian Fainelli:
New devices:
- Felix adds support for the Buffalo WXR-1900DHP and adds the USB led on Buffalo
WZR-1750DHP
- Rafal adds support for the SmartRG SR400ac, Asus RT-AC68U and RT-AC56U
New peripheral support:
- Brian adds Device Tree nodes for the Broadcom NAND controller found on
BCM7xxx, BCM63138 and Cygnus SoCs
- Brian adds Device Tree nodes for the SATA AHCI and PHY controller found on
BCM7xxx
- I add the Device Tree nodes and bindings documents for bringing-up secondary
CPUs and timer/syscon-reboot on BCM63138
* tag 'arm-soc/for-4.2/dts' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Add DT for Asus RT-AC56U
ARM: BCM5301X: Add DT for Asus RT-AC68U
ARM: dts: BCM63xx: Add timer and syscon-reboot nodes
dt-bindings: Add documentation for the BCM63138 timer and syscon-reboot
ARM: dts: brcmstb: add nodes for SATA controller and PHY
ARM: dts: cygnus: Enable NAND support for Cygnus
ARM: bcm63138: add NAND DT support
ARM: bcm7445: add NAND to DTS
ARM: BCM5301X: Add DT for SmartRG SR400ac
ARM: BCM5301X: Add DT for Buffalo WXR-1900DHP
ARM: BCM5301X: Add USB LED for Buffalo WZR-1750DHP
ARM: dts: BCM63xx: Add SMP nodes and required properties
Documentation: DT: Document SMP DT nodes and properties for BCM63138
ARM: dts: BCM63xx: Add PMB busses nodes
Documentation: DT: Add Broadcom BCM63138 PMB binding
The guidelines for adding automount support to a filesystem
in filesystems/automount-support.txt is out or date.
filesystems/autofs4.txt contains more current text, so replace
the out-of-date content with a reference to that.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In comments and in the documentation, the units of properties marked
with the FE_SCALE_DECIBEL scale are specified in terms of 1/1000 dB
or 0.0001 dB. This is inconsistent, however, as 1/1000 is 0.001,
not 0.0001.
Note that the v4l-utils divide the value by 1000 for the signal
strength suggesting that the 1/1000 is correct.
Settle on millidecibels, ie. 1/1000dB or 0.001dB.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I misunderstood this section as simply asking me to add an email Cc, and
was unaware of the existence of Documentation/stable_kernel_rules.txt.
Hopefully this clarification will help save maintainers and new/rare
submitters time in the future.
Signed-off-by: Luke Dashjr <luke-jr+git@utopios.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Some Ethernet PHY devices/switches may not properly release the MDIO bus
during turn-around time, and fail to drive it low, which can be seen by
some controllers as a read failure, while the data clocked in is still
correct.
Add a boolean property "broken-turn-around" which is parsed by the
generic MDIO bus probing code and will set the corresponding bit in the
MDIO bus phy_ignore_ta_mask bitmask for MDIO bus drivers to utilize that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds root compatible properties for the following boards:
- Raspberry Pi Model A
- Raspberry Pi Model A+
- Raspberry Pi Model B
- Raspberry Pi Model B (no P5)
- Raspberry Pi Model B rev2
- Raspberry Pi Model B+
- Raspberry Pi Compute Module
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
4a88d44ab1 ("tracing: Remove mentioning of legacy latency_trace file
from documentation") changed a sentence to refer to only one file
instead of two, but the sentence still uses "they". Fix it.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The SCC_MAGIC define was removed in commit 1ec3ba93c5 ("Staging:
remove drivers/char/scc.h as it should have gone a while ago"), while
its actual last user was removed before in commit bb2a97e9cc
("Staging: delete generic_serial drivers").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The SCI_MAGIC define was removed in commit f8e53553f4 ("serial:
sh-sci: Kill off more unused defines.").
Its last user was the old drivers/char sh-sci driver, which was removed
in 2004.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Currently Documentation/clk.txt describes an obsolete techinique to
statically define struct clk objects.
This capability was removed by b09d6d991025("clk: remove clk-private.h")
and is no longer supported. The documentation describing the feature should
be removed.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The binding uses assigned-clock-parents when it should use
assigned-clock-rates. Furthermore, the part that describes how
they relate to the assigned-clocks property is not clear about
what is related. Correct and clarify this part of the binding.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
