This patch adds basic board support for APQ8074 Dragonboard
which belongs to the Snapdragon 800 family.
For now, just support a basic machine with device tree.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
[olof: Split off SoC and board support in separate patches]
Signed-off-by: Olof Johansson <olof@lixom.net>
From Simon Horman:
Renesas ARM based SoC board updates for v3.14
* Global
- Kconfig: Mention Renesas ARM SoCs instead of SH-Mobile
* r7s72100 SoC (RZ/A1H) based Genmai Board
- Add Multiplatform support
- Add Reference DT
* r8a7791 (R-Car M2) based Koelsch board
- Add pinctrl_register_mappings() for Koelsch
- Hook up SW30-SW36 on Koelsch
- Mark GPIO keys as wake-up sources
- Use ->init_late()
- Add Multiplatform support
- Set .debounce_interval for GPIO keys
- Add SW2 to GPIO keys
- Add Led 6, 7 and 8 support
- Add reference DT
- Enable PFC/GPIO
* r8a7790 (R-Car H2) based Lager board
- Add gpio/fixed regulator for SDHI
- Add SPI FLASH support on QSPI
- Mark GPIO keys as wake-up sources
- Use ->init_late()
- Set .debounce_interval for GPIO keys
* r8a7778 (R-Car M1) based Bock-W board
- bockw: remove unused RSND_SSI_CLK_FROM_ADG
- Set .debounce_interval for GPIO keys
- Correct FPGA ioremap area
- Use regulator for MMCIF
* r8a7740 (R-Mobile A1) based Armadillo board
- Correct FSI address size
* sh7374 (SH-Mobile AP4) based Mackerel board
- Use pinconf API to configure pin pull-down
- clk_round_rate() can return a zero to indicate an error
* tag 'renesas-boards-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (75 commits)
ARM: shmobile: lager: add gpio/fixed regulator for SDHI
ARM: shmobile: bockw: remove unused RSND_SSI_CLK_FROM_ADG
ARM: shmobile: armadillo: fixup FSI address size
ARM: Kconfig: Mention Renesas ARM SoCs instead of SH-Mobile
ARM: shmobile: mackerel: Use pinconf API to configure pin pull-down
ARM: shmobile: Lager:add SPI FLASH support on QSPI
ARM: shmobile: mackerel: clk_round_rate() can return a zero to indicate an error
ARM: shmobile: Add pinctrl_register_mappings() for Koelsch
ARM: shmobile: Use ->init_late() on Lager
ARM: shmobile: Hook up SW30-SW36 on Koelsch
ARM: shmobile: koelsch: mark GPIO keys as wake-up sources
ARM: shmobile: Use ->init_late() on Koelsch
ARM: shmobile: lager: mark GPIO keys as wake-up sources
ARM: shmobile: r7s72100 Genmai Multiplatform
ARM: shmobile: r7s72100 Genmai DT reference C bits
ARM: shmobile: r7s72100 Genmai DT reference DTS bits
ARM: shmobile: Initial r8a7791 and Koelsch multiplatform support
ARM: shmobile: koelsch: set .debounce_interval
ARM: shmobile: lager: set .debounce_interval
ARM: shmobile: bockw: add pin pull-up setting for SDHI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds DT board setup for the LaCie NAS LaPlug.
Chipset list:
- CPU MARVELL 88FR131 800Mhz
- SDRAM memory: 128MB DDR2-800 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- 1 Mini PCI-Express port
- 1 NAND 512 MB
- 1 push button
- 2 LEDs (red and blue)
- 4 USB Ports
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the DTS file r8a7790-koelsch.dts can be used with
board-koelsch.c and board-koelsch-reference.c, proceed with removing
r8a7790-koelsch-reference.dts.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a generic (dtsi) include file for MOXA ART SoCs.
Also add a file for UC-7112-LX.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Simon Horman:
Renesas ARM based SoC DT updates for v3.14
* Global
- Use interrupt macros
- Use #include in device tree sources
- Tidyup DT node naming
* emev2 (Emma Mobile EV2) SoC
- Setup internal peripheral interrupts as level high
- Use interrupt macros in DT files
- Add clock tree description in DT
* r8a7791 (R-Car M2) SoC
- Correct GPIO resources
* r8a7791 (R-Car M2) based Koelsch board
- Configure PFC and GPO
- Use r8a7791 suffix for IRQC compat string
- Add DT reference
* r8a7790 (R-Car H2) based Lager board
- Include all 4 GiB of memory
- Use r8a7790 suffix for IRQC and MMCIF compat strings
- Enable MMCIF
- Add default PFC settings
* r8a7778 (R-Car M1) SoC
- Suffix for INTC compat string
- Add HSPI, MMCIF, SDHI and I2C suppport on DTSI
- Correct pin control device addresses
* r8a7778 (R-Car M1) based Bock-W board
- Use falling edge IRQ for LAN9221 in DT reference
- Enable I2C, HSPI0, MMCIF and SDHI
- Correct MMC pin conflict
- Remove manual PFC settings from DT reference
- Add default PFC settings
* r8a7779 (R-Car H1) SoC
- Add HSPI and SDHI support
- Suffix for INTC compat string
* r8a7779 (R-Car H1) based Marzen board
- Enable HSPI0 and SDHI in DTS
- Remove SDHI0 WP pin setting
- Use falling edge IRQ for LAN9221 in DT reference
- Add SDHI support
* r8a7740 (R-Mobile A1) SoC
- Suffix for INTC compat string
- Add FSI support via DTSI
- Use interrupt macros
* r8a7740 based Armadillo board
- Add FSI support for DTS
- Use low level IRQ for ST1231 in DT reference
* r8a73a4 (SH-Mobile APE6) SoC
- Use interrupt macros in DT files
* r8a73a4 (R-Mobile APE6) based ape6evm board
- Include all 2 GiB of memory
* r8a73a0 (SH-Mobile AG5) SoC
- Correct SDHI compat string
* r8a73a0 (SH-Mobile AG5) based kzm9d board
- Add GPIO keys and Add PCF8575 GPIO extender to DT
- Enable DSW2 with gpio-keys
- Use falling edge IRQ for LAN9221 in DT reference
* tag 'renesas-dt-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (102 commits)
ARM: shmobile: marzen: enable HSPI0 in DTS
ARM: shmobile: r8a7779: add HSPI support to DTSI
ARM: shmobile: Use r8a7779 suffix for INTC compat string
ARM: shmobile: Use r8a7778 suffix for INTC compat string
ARM: shmobile: Use r8a7740 suffix for INTC compat string
ARM: shmobile: Use sh73a0 suffix for INTC compat string
ARM: shmobile: armadillo: add FSI support for DTS
ARM: shmobile: r8a7740: add FSI support via DTSI
ARM: shmobile: emev2: Setup internal peripheral interrupts as level high
ARM: shmobile: emev2: Use interrupt macros in DT files
ARM: shmobile: Use interrupt macros in r8a73a4 and r8a7778 DT files
ARM: shmobile: Fix r8a7791 GPIO resources in DTS
ARM: shmobile: Include all 4 GiB of memory on Lager DT Ref
ARM: shmobile: Include all 4 GiB of memory on Lager
ARM: shmobile: Include all 2 GiB of memory on APE6EVM
ARM: shmobile: Include all 2 GiB of memory on APE6EVM DT Ref
ARM: shmobile: kzm9g-reference: Add GPIO keys to DT
ARM: shmobile: kzm9g-reference: Add PCF8575 GPIO extender to DT
ARM: shmobile: Koelsch DT reference GPIO LED support
ARM: shmobile: Enable DSW2 with gpio-keys on KZM9D
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
From Uwe Kleine-König:
* efm32/soc: (1003 commits)
ARM: device trees for Energy Micro's EFM32 Cortex-M3 SoCs
ARM: new platform for Energy Micro's EFM32 Cortex-M3 SoCs
+Linux 3.13-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
We want to follow the name style of DTS that is SoC-board.dts.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Now that r8a7790 has CCF support remove the legacy Lager reference
Kconfig bits CONFIG_MACH_LAGER_REFERENCE for the non-multiplatform
case.
Starting from this commit Lager board support is always enabled via
CONFIG_MACH_LAGER, and CONFIG_ARCH_MULTIPLATFORM is used to select
between board-lager.c and board-lager-reference.c
The file board-lager-reference.c can no longer be used together with
the legacy sh-clk clock framework, instead CCF is used.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable multiplaform ARM architecture support for the Lager reference
board. Common clock framework initialization will be handled by the
rcar_gen2_init_timer() call, we just need to remove the legacy clock
code initialization.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds support for CompuLab SBC-T3530, also known as cm-t3730:
http://compulab.co.il/products/sbcs/sbc-t3530/
It seems that with the sbc-3xxx mainboard is also used on
SBC-T3517 and SBC-T3730 with just a different CPU module:
http://compulab.co.il/products/sbcs/sbc-t3517/http://compulab.co.il/products/sbcs/sbc-t3730/
So let's add a common omap3-sb-t35.dtsi and then separate SoC
specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and
omap3-sbc-t3517.dts.
I've tested this with SBC-T3730 as that's the only one I have.
At least serial, both Ethernet controllers, MMC, and wl12xx WLAN
work.
Note that WLAN seems to be different for SBC-T3530. And SBC-T3517
may need some changes for the EMAC Ethernet if that's used
instead of the smsc911x.
Cc: devicetree@vger.kernel.org
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable Hisilicon Hi4511 development platform with device tree support.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The A13-OLinuXino-MICRO is a small dev-board with the Allwinner A13 SoC:
https://www.olimex.com/Products/OLinuXino/A13/A13-OLinuXino-MICRO/
Features:
A13 Cortex A8 processor at 1GHz, 3D Mali400 GPU
256 MB RAM (128Mbit x 16)
5VDC input power supply with own ICs, noise immune design
1 USB host
1 USB OTG which can power the board
SD-card connector for booting the Linux image
VGA video output
LCD signals available on connector so you still can use LCD if you disable VGA/HDMI
Audio output
Microphone input pads (no connector)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds very basic device tree files for the Marvell Armada
1500-mini SoC (Berlin BG2CD) and the Google Chromecast. Currently,
SoC only has nodes for cpu, some clocks, l2 cache controller, local
timer, apb timers, uart, and interrupt controllers.
The Google Chromecast is a consumer device comprising the Armada
1500-mini SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This adds very basic device tree files for the Marvell Armada 1500 SoC
(Berlin BG2) and the Sony NSZ-GS7 GoogleTV board. Currently, SoC only has
nodes for cpus, some clocks, l2 cache controller, local timer, apb timers,
uart, and interrupt controllers. The Sony NSZ-GS7 is a GoogleTV consumer
device comprising the Armada 1500 SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
From Nicolas Ferre:
First DT pull-request for 3.14
- many little corrections and documentation updates
- LCD FB Device Tree for at91sam9263 and at91sam9g45 boards
- crypto peripherals DT entries + DMA specification
- new Cosino board
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/at91rm9200ek.dts: rearrange nodes in address ascending order
ARM: at91: dt: at91rm9200ek: add emac and nor flash support
ARM: at91: add uart aliases to sama5d3 dtsi
ARM: at91: add i2c2 pinctrl speficifation to sama5d3 DT
ARM: at91: Animeo IP: fix mtd partition table
ARM: at91: at91sam9g45: add i2c pinctrl
ARM: at91: at91sam9g45: set default mmc pinctrl-names
ARM: at91: sama5d3: enable qt1070 as a wakeup source
ARM: at91: add support for Cosino board series by HCE Engineering
ARM: at91/dt/sama5d3: add DMA information to SHA/AES/TDES nodes
ARM: at91/dt/trivial: before sama5d3, Atmel MPU were using at91 prefix
ARM: at91/dt/trivial: use macro for AES irq type
ARM: at91: sam9263ek: add dt lcd support
ARM: at91: at9sam9m10g45ek: add dt lcd support
ARM: at91: sam9263: add fb dt support
ARM: at91: sam9g45: add fb dt support
ARM: at91/dt: binding: add missing compatibility string in SDRAM/DDR documentation
ARM: at91/dt: binding: add precision to AIC documentation
ARM: at91/dt: add atmel,pullup-gpio to at91rm9200ek usb1 definition
ARM: at91/dt: add ethernet phy to at91rm9200ek board
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add Koelsch and r8a7791 to CONFIG_SHMOBILE_MULTI. At this
point CCF is not yet supported so you cannot run this code
yet. For CCF support to happen several different components
are needed, and this is one simple portion that moves us
forward. Other patches need to build on top of this one.
Koelsch board support exists in 3 flavors:
1) SHMOBILE_MULTI, MACH_KOELSCH - board-koelsch-reference.c (CCF + DT)
2) SHMOBILE, MACH_KOELSCH_REFERENCE - board-koelsch-reference.c (DT)
3) SHMOBILE, MACH_KOELSCH - board-koelsch.c (legacy C code)
When CCF is done then 2) will be removed. When 1) includes same features
as 3) then 3) will be removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SH-Mobile platforms are transitioning from non-multiplatform to
multiplatform kernel. A new ARCH_SHMOBILE_MULTI configuration symbol has
been created to group all multiplatform-enabled SH-Mobile SoCs. The
existing ARCH_SHMOBILE configuration symbol groups SoCs that haven't
been converted yet.
This arrangement works fine for the arch/ code, but lots of drivers
needed on both ARCH_SHMOBILE and ARCH_SHMOBILE_MULTI depend on
ARCH_SHMOBILE only. In order to avoid changing them, rename
ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY, and create a new boolean
ARCH_SHMOBILE configuration symbol that is selected by both
ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the Cosino at91sam9g35 based CPU module and the
Cosino Mega 2560 extension board.
Web site: http://www.cosino.it
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
[plagnioj@jcrosoft.com: added "at91-" to files, pinctrl fixed, removed unneeded stuff]
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: adapted to newer kernel, modified commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Almost all hardware parts of the NETGEAR ReadyNAS NV+ v2 ([1] for more
details) are supported by mainline kernel. The only missing elements in
provided .dts file are:
- the front LCD module (Winstar WINSTAR WH1602): driver development is
ongoing. This is the same LCD module as on ReadyNAS 104.
- the Macronix MX25L512 512Kbit SPI flash: no time to play with it yet.
The device is the big brother (4 vs 2 bay) of the ReadyNAS Duo v2. The
main differences are some additional LEDs for the disks, a Marvell
88SM4140 SATA Port multiplier (no driver required to access the disk)
and previously described LCD module. Otherwise, it shares the same SoC
(kirkwood 88F6282), RAM (256MB), NAND (128MB), RTC chip (Ricoh rs5c372a),
fan controller (GMT G762), XHCI controller (NEC/Renesas µPD720200).
[1]: http://natisbad.org/NAS5/
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
All hardware parts of the (mv78230 Armada XP based) NETGEAR ReadyNAS
2120 are supported by mainline kernel (USB 3.0 and eSATA rear ports,
USB 2.0 front port, Gigabit controller and PHYs for the two rear ports,
serial port, LEDs, Buttons, 88SE9170 SATA controllers, three G762 fan
controllers, G751 temperature sensor) except for:
- the Intersil ISL12057 I2C RTC Chip,
- the Armada NAND controller.
Support for both of those is currently work in progress and does not
prevent boot.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Basic things like serial, Ethernet, MMC, NAND, DSS, touchscreen
and GPIO keys work.
For twl4030-keypad we're still missing the binding, but
support for that should be trivial to add once the driver
has been updated.
MUSB I'm pretty sure I got got to enumerate once, but I
suspect the battery charging somehow disrupts it and it's
not enumerating in general for some reason.
Patches are welcome to improve things if people are
still using this board.
For reference, here's some more info on this old board:
http://www.openomap.org/wiki/tiki-index.php?page=HardwareInfo
Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal device tree support for n8x0 boards so we
can make omap2 device tree only. Note that we still need
to initialize various platform data quirks to keep
things working until n8x0 drivers support device tree.
Here's a rough todo list for the people using n8x0:
1. Update menelaus for device tree and set up
regulators at least for the MMC driver
2. Remove the MMC regulator platform data callback
by using the Menlaus regulators directly in the
driver passed from the .dts file
3. Update GPMC connected devices for onenand and
tusb6010 for device tree
We're planning to remove all legacy platform data
for mach-omap2 over next few merge cycles, so if
people are still using n8x0, please fix the issues
above.
Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I doubt that there are many people using 2430 sdp, but as
that's been historically an important acid test platform
for omap2+ related changes, let's add minimal device
tree support for it.
If anybody is using it beyond minimal boot testing, patches
for more complete device tree support are welcome.
Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
Pull ARM SoC board updates from Olof Johansson:
"Board-related updates. This branch is getting smaller and smaller,
which is the whole idea so that's reassuring.
Right now by far most of the code is related to shmobile updates, and
they are now switching over to removal of board code and migration to
multiplatform, so we'll see their board code base shrink in the near
future too, I hope.
In addition to that is some defconfig updates, some display updates
for OMAP and a bit of new board support for Rockchip boards"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (56 commits)
ARM: rockchip: add support for rk3188 and Radxa Rock board
ARM: rockchip: add dts for bqcurie2 tablet
ARM: rockchip: enable arm-global-timer
ARM: rockchip: move shared dt properties to common source file
ARM: OMAP2+: display: Create omap_vout device inside omap_display_init
ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init
ARM: OMAP2+: display: Create omapdrm device inside omap_display_init
ARM: OMAP2+: drm: Don't build device for DMM
ARM: tegra: defconfig updates
RX-51: Add support for OMAP3 ROM Random Number Generator
ARM: OMAP3: RX-51: ARM errata 430973 workaround
ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1
ARM: shmobile: marzen: enable INTC IRQ
ARM: shmobile: bockw: add SMSC support on reference
ARM: shmobile: Use SMP on Koelsch
ARM: shmobile: Remove KZM9D reference DTS
ARM: shmobile: Let KZM9D multiplatform boot with KZM9D DTB
ARM: shmobile: Remove non-multiplatform KZM9D reference support
ARM: shmobile: Use KZM9D without reference for multiplatform
ARM: shmobile: Sync KZM9D DTS with KZM9D reference DTS
...
From Jason Cooper:
- add the Openblocks A7 board
- add Netgear ReadyNAS 104 board
* tag 'dt-3.13-5' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: kirkwood: add support for OpenBlocks A7 platform
Signed-off-by: Olof Johansson <olof@lixom.net>
A handful of DT updates from Christian Daudt for the broadcom mobile
platforms, including their rename of the platform to BCM_MOBILE to keep
BCM for the vendor-level options.
* bcm/dt:
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently ARCH_BCM has been used for Broadcom
Mobile V7 based SoCs. In order to allow other Broadcom
SoCs to also use mach-bcm directory and files, this patch
renames the original ARCH_BCM to ARCH_BCM_MOBILE, and
uses ARCH_BCM to define any Broadcom chip residing
in mach-bcm directory.
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Main hardware parts of the (Armada 370 based) NETGEAR ReadyNAS 104 are
supported by mainline kernel (USB 3.0 rear ports, USB 2.0 front port,
Gigabit controller and PHYs, serial port, LEDs, buttons, SATA ports,
G762 fan controller) and referenced in provided .dts file. Some additonal
work remains for:
- Intersil ISL12057 I2C RTC and Alarm chip: working driver but needs
to be splitted for submission of RTC part first;
- Front LCD (Winstar 1602G): driver needs to be written
- Armada NAND controller (to access onboard 128MB of NAND): support
being pushed by @free-electrons people
- 4 front SATA LEDs controlled via GPIO brought by NXP PCA9554:
driver is available upstream. Not referenced/tested yet.
but the device is usable w/o those.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The OpenBlocks A7 board is designed and sold by PlatHome, and based on
a Kirkwood 6283 Marvell SoC. It is quite similar to the OpenBlocks A6
already supported in the kernel, with the following main differences:
- The A6 uses a RTC on I2C, while the A7 uses the internal SoC RTC.
- The A6 has one Ethernet port, while the A7 has two Ethernet ports
- The A6 has only one USB port, while the A7 integrates a USB hub,
which provides two front-side USB port, and an internal USB port as
well.
- The A6 has 512 MB of RAM, while the A7 has 1 GB of RAM.
- Slightly different GPIOs for some functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:
- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272
* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
ARM: dts: TWL4030: Add power button support
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add TLV320AIC3X support
ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
ARM: dts: omap3-n900: Add NAND support
ARM: dts: omap3-n900: Specify regulator info
ARM: dts: TWL4030: Add missing regulators
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add vibrator device
ARM: dts: omap3-n900: GPIO key definitions
ARM: dts: omap3-n900: Add support for SD cards
ARM: dts: omap3-n900: Add UART support
ARM: dts: omap3-n900: Fix i2c bus speed
ARM: dts: omap3-n900: Add pinctrl for i2c devices
ARM: dts: DRA7: Add CPU OPP table
ARM: dts: OMAP5: Add CPU OPP table
ARM: dts: dra7-evm: add smps123 supply for CPU
ARM: dts: omap5-uevm: add smps123 supply for CPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
From Shawn Guo:
The imx/mxs device tree changes for 3.13:
- Use macros for mxs pinctrl settings
- New board support: VF610 Cosmic/Cosmic+, imx6q-udoo, MSR M28CU3
- Support DSPI device for vf610
- Add PCIe device for imx6qdl
- Add UHS pinctrl states for imx6sl and imx6qdl
- Display support for APF and imx51-babbage boards
- Enable SPI NOR and USB for imx6sl-evk board
- Enable LVDS for imx6q-sabrelite and SPDIF for imx6qdl-wandboard
- Misc updates on boards: TX28, imx6qdl-wandboard, imx53-qsb etc.
- Some random updates on imx51 device tree
* tag 'imx-dt-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6: (44 commits)
ARM: imx: imx6sl iomuxc syscon is compatible to imx6q
ARM: dts: imx6sl-evk: enable the SPI NOR
ARM: dts: imx6sl: add a pinctrl for ECSPI1
ARM: imx27: add missing #pwm-cells property
ARM: dts: imx6sl: add pinctrl uhs states for usdhc
ARM: dts: imx6qdl-sabresd: Add backlight support for lvds
ARM: dts: imx51-babbage: Make DVI and WVGA panel functional
ARM: imx27-apf27dev: Add framebuffer support
ARM: imx51-apf51dev: Add parallel display support
ARM: dts: imx53-qsb: Do not use GPIO1_8 as wakeup source
ARM: dts: imx53-qsb: SDHC1 does not have cd-gpios
ARM: dts: imx53-qsb: SDHC3 is connected in 8-bit mode
ARM: dts: mxs: Add MSR M28CU3 board
ARM: dts: imx6qdl-wandboard: Provide phy-reset-gpios
ARM: dts: imx6qdl-sabresd: Provide phy-reset-gpios
ARM: dts: imx6q-sabrelite: Add ethernet phy reset pin into hog
ARM: dts: imx6qdl: add pcie device node
ARM: dts: imx6q-udoo: Add initial board support
ARM: dts: mxs: Add muxing options for the SSP2 MMC
ARM: dts: add initial VF610 Cosmic/Cosmic+ board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Maxime Ripard:
Allwinner sunXi SoCs device tree changes for 3.13
This DT series sees the introduction of the cubietruck DT, plus the addition of
the i2c controller for the A20 based boards, and of the Security ID found in
all the Allwinner SoCs but the A31.
* tag 'sunxi-dt-for-3.13' of https://github.com/mripard/linux:
ARM: sunxi: dts: Add support for the cubieboard3, the CubieTruck
ARM: sun7i: olinuxino-micro: Enable the I2C controllers
ARM: sun7i: cubieboard2: Enable the I2C controllers
ARM: sun7i: Add the pin muxing options for the I2C controllers
ARM: sun7i: Enable the I2C controllers
ARM: sunxi: dt: Add sunxi-sid to dts for sun4i, sun5i and sun7i
Signed-off-by: Olof Johansson <olof@lixom.net>
NanoBone Specification:
-----------------------
CPU:
TI AM335x
Memory:
256MB DDR3
128MB NOR flash
128KB FRAM
Ethernet:
2 x 10/100 connected to SMSC LAN8710 PHY
USB:
1 x USB2.0 Type A
I2C:
2Kbit EEPROM (Microchip 24AA02)
RTC (Maxim DS1338)
GPIO Expander (Microchip MCP23017)
Expansion connector:
6 x UART
1 x MMC/SD
1 x USB2.0
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
From Tony Lindgren:
Changes needed to drop legacy booting support for some
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
* tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (125 commits)
ARM: OMAP2+: remove legacy support for IGEP boards
ARM: OMAP2+: Remove legacy support for zoom platforms
ARM: OMAP2+: Remove legacy booting support for omap3 EVM
ARM: OMAP2: delete board-rm680
ARM: dts: add minimal DT support for Nokia N950 & N9 phones
ARM: dts: Add basic support for zoom3
ARM: dts: Add basic support for TMDSEVM3730 (Mistral AM/DM37x EVM)
ARM: dts: Add common support for omap3-evm
ARM: dts: Shared file for omap GPMC connected smsc911x
+Linux 3.12-rc5
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add minimal DT support for Nokia N950 & N9 phones. The same functionality
that is provided by the current board file should work: serial console,
USB, OneNAND and MMC.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
