Since ("ARM: shmobile: r8a73a4: ape6evm: Remove legacy platform"),
ape6evm is restricted to booting from DT, so chosen/stdout-path is
always used, and we can drop the "console=" parameter from
chosen/bootargs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the r8a73a4 generic multiplatform case has the same features as the
APE6EVM DT reference board code, we get rid of the latter. DT reference
code in the future shall make use of the r8a73a4 multiplatform support code
with the generic SoC machine vector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[geert: Update Documentation/devicetree/bindings/arm/shmobile.txt]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently the pin function controller (which is also a GPIO controller)
is instantiated before the interrupt controllers due to the order in the
DTS. At that time, the irq domains for the interrupt controllers
referenced by its interrupts-extended property cannot be found yet:
irq: no irq domain found for /interrupt-controller@e61c0000 !
Nevertheless, the core OF probing code ignores this failure, besides a
debug message that's not normally printed:
not all legacy IRQ resources mapped for pfc
and continues initialization of the device. Then, the sh-pfc driver
cannot find any IRQ resources, and thinks no interrupts are available,
causing gpio-keys to fail later:
gpio-keys keyboard: Unable to claim irq 0; error -22
gpio-keys: probe of keyboard failed with error -22
Move the pin function controller node after the interrupt controller
nodes it references to work around the bug in the core OF probing code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node from the ad-hoc lbsc node to the BSC node,
as its connected to the Bus State Controller. This allows the system to
know the right position of the Ethernet node in the clock and PM domain
hierarchy, and manage the clock and PM domain appropriately.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Bus State Controller (BSC) on r8a73a4, to which
multiple external devices can be connected.
The BSC is driven by the ZB clock, and located in PM domain C4.
A reference to the latter will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
Fixes: 59e79895b9 ("ARM: shmobile: r8a7791: Add clocks")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
* Correct base address of SD3 div6 clk.
* Update div6 clock node labels
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
This has no run-time affect as the clock nodes are not currently used.
Fixes: 8e181633e6 ("ARM: shmobile: r8a7794: Add SDHI clocks to device tree")
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the ethernet controller for the Alt board. Pin muxing entries are
currently left out as r8a7794 pin control support isn't available yet.
We thus rely on the boot loader to configure ethernet pins for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the ADXL345 three-axis digital accelerometer sensor,
which is connected to i2c0.
As trivial i2c devices are matched against the first compatible entry
only, compatibility is declared with "adi,adxl34x" only for now.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device needs an interrupt to operate properly. Specify the two
interrupts used on the board.
While at it rename the DT node to accelerometer@1d to describe the
device's function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the AK8975 magnetometer sensor, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Specify the device interrupt to avoid polling for end of conversion.
While at it rename the DT node to compass@c to describe the device's
function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While at it rename the ak4648 node to "codec" to describe the device's
function instead of its model, and move its device-specific property
after its generic properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sh73a0 INTC can't mask interrupts properly most likely due to a
hardware bug. Set the control-parent property to delegate masking to the
parent interrupt controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Device Tree description of SDHCI on Armada 388 RD board was
missing. This commit adds the node for it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The binding of the armada-380-sdhci has been extended with a new
register in order to be able to use the SDR50 and DDR50 mode. This
commit add the resource associated to this new register for the
Armada 38x.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Instead of hardcoding the values of the interrupt flags, use the
macros provided by <include/dt-bindings/interrupt-controller/irq.h>
and <include/dt-bindings/interrupt-controller/arm-gic.h> for the
Armada 38x SDHCI node.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This was left out of the original firefly board definition due to the
ethernet support going completely through the network tree, making the
underlying nodes unavailable.
Now that everything is present enable the gmac on the firefly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
