Currently oscillator frequency is determined based on sysboot settings,
it may not be the case always. To determine it properly, efuse settings
also has to be read. CONTROL_STATUS register holds this information.
Bit 31: if 0, frequency to be determined based on sysboot
if 1, frequency to be determined based on efuse
Bit 29,30 - for efuse detection of frequency
Bit 22,23 - for sysboot detection of frequency
Add clock nodes (mux) to determine oscillator frequency as above.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We need set-rate-parent flags for the display's clock path so that the
DSS driver can change the clock rate of the PLL.
This patchs adds the ti,set-rate-parent flag to disp_clk and
dpll_disp_m2_ck clock nodes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add ti,set-rate-parent to dss_dss_clk so that the DSS driver can
set the rate.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Booting Linux 3.14 on Pandaboard currently gets the following
message displayed:
smp_twd: clock not found -2
Define "mpu_periphclk" as the twd clock in omap4 dts to avoid this.
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
abe_iclk's parent is aess_fclk and not abe_clk.
Also correct the parameters for clock rate calculation as used for OMAP4
since in PRCM level there's no difference between the two platform
regarding to AESS/ABE clocking.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
In OMAP5 bit 8 in PRCM registers are not defined (Reserved) unlike their
counterpart in OMAP4.
It is better to not write to these bits.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We need "tbclk" clock data for the functioning of ehrpwm
module. Hence, populating the required clock information
in clock dts file.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
tbclk does not need to be a composite clock, we can simply
use gate clock for this purpose.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add support for the 2 SDHC controllers on the DB8074 board. The first
controller (at 0xf9824900) is connected to an on board soldered eMMC.
The second controller (at 0xf98a4900) is connected to a uSD card slot.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The SoCFPGA has two watchdog timers. Add them to the dtsi.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[dinh: modified patch to have correct irq flag]
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The cycloneV has three gpio controllers, each one with 29 gpios. This patch
adds the three controller with the gpio driver which is now sitting the
gpio tree.
Cc: devicetree@vger.kernel.org
Acked-by: Alan Tull <atull@altera.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
This patch enables a exynos_usbphy node for exynos4 SoCs.
A exynos4x12 usb phy node is almost same with 4210's one
except compatible string and pmu syscon.
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
sss module device node missed clock macro.
This patch replace magic number with macro in clock
binding for exynos5420.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Phy and sss module device node missed clock macro.
This patch replace magic number with macros in clock
binding for exynos5250.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables support for multimedia blocks - fimc in
mem2mem mode, no camera sensors support yet.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree nodes necessary to enable USB support on
universalc210 board, this includes UDC controller (USB gadget) as well
as EHCI and OHCI host ports. LDO3 and LDO8 regulators are switched to
always on mode until EHCI and OHCI drivers will support them correctly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device tree nodes necessary to enable USB
gadget functionality on Exynos4210-based Trats board.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the audio subsystem clock controller and the I2S
IP block nodes for Exynos4 SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixed gpio key device node.
First, fix incorrect gpio property.
And then, add ok-key node where locate bottom center.
I have tested on exynos4412-trats2 board.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos4412-trats2 board have light/proximity sensor.
This patch add cm36651 light/ proximity sensor node for exynos4412.
cm36651 is required properties as below.
- Use i2c-gpio for cm36651 sensor.
- Use fixed regulator for the IR LED.
It is a part of the cm36651 for proximity detection.
- cm36651 is i2c device driver so need to use i2c-gpio driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Due a copy/paste error, the 'reg' values for the third PCIe interface
on Armada 380, and the third and fourth PCIe interfaces on Armada 385
are wrong: they are equal to the one of the second PCIe interface.
This patch fixes this by using the appropriate 'reg' values for those
PCIe interfaces.
Without this fix, the third and fourth PCIe interfaces are unusable on
those platforms.
Reported-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1400597008-4148-1-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: 0d3d96ab00 ("ARM: mvebu: add Device Tree description of the Armada 380/385 SoCs")
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The i12 tvbox is an A20 based android tvbox, with 512M / 1G RAM, 4G nand flash,
ap6210 or ap6330 sdio wifi + bt (broadcom sdio wifi + uart attached brcm bt),
2USB host ports using USB-A receptacles and a micro-usb receptacle for USB OTG,
and 100Mbit ethernet using an IP101a phy.
The PCB is labelled i12-a20 hence I've named the board i12-a20. It is used
in noname allwinner A20 tv-boxes, which are sometimes sold with Q5 or
QT840A as product name.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
bus-width defaults to 1, and all 4 lines are hooked up at the cubietruck,
properly set bus-width to 4.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
dma-channels, ti,edma-regions and ti,edma-slots no longer needed in DT since
the the same information is available in the IP's CCCFG register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Colombus has a full size SD slot wired to the MMC0 controller. In order to
work, the MMC lines have to have the pull-ups enabled though.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The unit-address doesn't match the reg property. Since the reg property is
correct, change the unit-address accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The colombus board has a on-board USB hub, that is enabled through the pin
PH24, and wired to the first EHCI controller.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Switch the device tree to the new compatibles introduced in the i2c drivers
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Samsung DT updates for v3.16
- exynos4
: add missing pinctrls
- exynos4412-trats2
: update camera nodes and add rear camera nodes
: rename alias for i2c_ak8975 label
Update camera nodes for exynos4 and exynos4412-trats2
- exynos5250
: update DWC3 usb controller and enable to use generic USB DRD phy
- exynos5250-snow
: enable dp-controller, fimd, hdmi and pwm backlight
: add sound node and Vbus regulator for USB 3.0
: add tps65090 power regulator
: add pinctrl for EC irq and i2c-arbitrator
- exynos5420
: change to correct compatible string for hdmi
: add PD entry to MFC codec and enable DWC3 and USB 3.0 PHY
: add MFC memory banks for smdk5420 and arndale-octa boards
- exynos5420-peach-pit
: add support exynos5420 based peach-pit board
: add sound node and Vbus regulatro for USB 3.0
: enable dp-controller, fimd
- exynos5420-smdk5420
: add Vbus regulatro for USB 3.0
- use generic DT bindings for map SYSRAM
[olof: Fixed up conflict with a fix for 4212 secondary CPU startup, carrying
over the fix to the reworked code]
* tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (32 commits)
ARM: dts: Add MFC memory banks to exynos5420 boards
ARM: dts: enable dp-controller for exynos5420-peach-pit board
ARM: dts: enable fimd for exynos5420 based peach-pit board
ARM: dts: enable dp-controller for exynos5250-snow board
ARM: dts: enable fimd for exynos5250-snow board
ARM: dts: enable pwm backlight for exynos5250-snow
ARM: dts: Add pwmX_out pinctrl nodes to exynos5250
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-smdk5420
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5420-peach-pit
ARM: dts: Add Vbus regulator for USB 3.0 on exynos5250-snow
ARM: dts: Add PD entry to MFC codec on exynos5420
ARM: dts: Add sound node for exynos5420-peach-pit board
ARM: dts: Add sound node for exynos5250-snow board
ARM: dts: Update DWC3 usb controller to use new phy driver for exynos5250
ARM: dts: Enable support for generic USB DRD phy for exynos5250
ARM: dts: Enable support for DWC3 controller for exynos5420
ARM: dts: Enable support for USB 3.0 PHY controller for exynos5420
ARM: dts: enable hdmi for exynos5420-peach-pit board
ARM: dts: change to correct compatible string for exynos5420 hdmi
ARM: dts: enable hdmi for exynos5250 based snow board
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in Samsung fixes for 3.15-rc to avoid an annoying context conflict
with new DT code.
* commit '702b691e4a71':
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung S3C24XX updates for 3.16" from Kukjin Kim:
Samsung S3C24XX to use the common clock framework
- S3C2412, S3C2413, S3C2416 and S3C2443 to use CCF
- S3C2410, S3C2440, S3C2442 to use CCF
- Remove legacy samsung clock from mach-s3c24xx/
- Some of them are missed from previous pull-request
- Clock related sutff got ack from Mike and Tomasz
- Created the last commit due to missing changes
during re-sorting because this branch is provided
as a base to samsung clk tree.
* tag 's3c24xx-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (23 commits)
ARM: S3C24XX: fix merge conflict
ARM: S3C24XX: remove SAMSUNG_CLOCK remnants after ccf conversion
ARM: S3C24XX: remove legacy clock code
ARM: S3C24XX: convert s3c2410 to common clock framework
ARM: S3C24XX: convert s3c2440 and s3c2442 to common clock framework
ARM: S3C24XX: add platform code for conversion to the common clock framework
clk: samsung: add clock controller driver for s3c2410, s3c2440 and s3c2442
dt-bindings: add documentation for s3c2410 clock controller
ARM: S3C24XX: enable usage of common dclk if common clock framework is enabled
clk: samsung: add clock driver for external clock outputs
ARM: S3C24XX: cpufreq-utils: don't write raw values to MPLLCON when using ccf
ARM: S3C24XX: convert s3c2412 to common clock framework
clk: samsung: add clock controller driver for s3c2412
dt-bindings: add documentation for s3c2412 clock controller
clk: samsung: add plls used by the early s3c24xx cpus
ARM: S3C24XX: only store clock registers when old clock code is active
ARM: S3C24XX: Convert s3c2416 and s3c2443 to common clock framework
ARM: dts: add clock data for s3c2416
ARM: S3C24XX: prevent conflicts between ccf and non-ccf s3c24xx-socs
clk: samsung: add clock-driver for s3c2416, s3c2443 and s3c2450
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung fixes for 3.15 from Kukjin Kim:
- Remove g2d_pd and mau_pd nodes on exynos5420.
Since the power domains are linked to the CMU blocks,
kernel panic happens during access clocks when the
power domains are disabled. Now this is a best solution.
- Enable HS-I2C on exynos5 by default
MMC partition cannot be mounted for RFS without the
enabling HS-I2C because regulators for MMC power are
connected to HS-I2C bus.
- Disable MDMA1 node on exynos5420
When MDMA1 runs in secure mode it makes kernel fault,
so need to disalbe it on exynos5420 by default instead
of each board.
- Fix the secondary CPU boot for exynos4212
* tag 'samsung-fixes' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Remove g2d_pd node for exynos5420
ARM: dts: Remove mau_pd node for exynos5420
ARM: exynos_defconfig: enable HS-I2C to fix for mmc partition mount
ARM: dts: disable MDMA1 node for exynos5420
ARM: EXYNOS: fix the secondary CPU boot of exynos4212
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Second Round of Renesas ARM Based SoC r7s72100 CCF Updates for v3.16"
from Simon Horman:
r7s72100 (RZ/A1H) SoC based Genmai board
* Remove non-multiplatform support from genmai-reference
* tag 'renesas-r7s72100-ccf2-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove Genmai reference DTS
ARM: shmobile: Let Genmai multiplatform boot with Genmai DTB
ARM: shmobile: Sync Genmai DTS with Genmai reference DTS
ARM: shmobile: genmai-reference: Remove legacy clock support
ARM: shmobile: Remove non-multiplatform Genmai reference support
Signed-off-by: Olof Johansson <olof@lixom.net>
