Merge "Two more dt related efm32 fixes" from Uwe Kleine-König:
* tag 'efm32-next' of git://git.pengutronix.de/git/ukl/linux:
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The BCM28155-AP board has a bootloader that expects the camldo1
regulator to be enabled on entry. Currently, the camldo1 regulator
is disabled when no longer in use as is the case during a reboot /
warm reset. This causes the early bootloader to hang upon entry. Add
regulator-always-on to the camldo1 constraint to fix reboot.
Reported-by: Alex Elder <elder@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Tested-by: Alex Elder <elder@linaro.org>
Add a dtsi to support the BCM590xx PMUs used by the BCM281xx family
of SoCs. Enable regulators for use with the dwc2 and sdhci on
bcm28155-ap.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Wolfram Sang pointed out during review of an efm32-i2c driver that the
property to specify the set of pins has a too general name. As several
other efm32 peripherals also have a similar register bit field, add an
"efm32" namespace.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
While removing the 0x prefixes in the unit addresses in reply to a review
comment, I must somehow have messed up these two. Uups.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Use a meaningful name for the reference clocks so that it indicates the
function.
Update the OMAP4+ USB Host node as well to be in sync with the changes.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DT node's unit address should be its own register offset address to make it a
unique across the system. This patch corrects the incorrect USB entries with
correct register offset for unit address.
Cc: stable@vger.kernel.org # v3.12+
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPMC clock is derived from l3_ick. The simplest solution is
to reference directly l3_ick to provide the GPMC fck in order to
get correct timings. The real management of the clock is left to
hwmod.
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The watchdog compatibles were following a different pattern than the one found
in the other devices. Now that the driver supports the right pattern, switch to
it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Remove the properties that are not used anymore by the at91_adc driver and fix
the atmel,adc-use-external-triggers property name.
Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Remove the properties that are not used anymore by the at91_adc driver and fix
the atmel,adc-use-external-triggers property name.
Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Remove the properties that are not used anymore by the at91_adc driver.
Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Remove the properties that are not used anymore by the at91_adc driver.
Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Summit is an expansion board for Gumstix Overo products.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Chestnut43 is an expansion board for Gumstix Overo products.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Alto35 is an expansion board for Gumstix Overo products.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gallop43 is an expansion board for Gumstix Overo products.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Palo43 is an expansion board for Gumstix Overo products.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LIS33DE accelerometer is used on several Gumstix expansion boards,
thus add the DT node to omap3-overo-common-peripherals.dtsi.
For the boards that do not have the accelerometer (like Tobi), mark the
status as disabled.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gumstix expansion boards share a couple of peripherals:
- uart3 is used for the console
- AT24C01 EEPROM on i2c3
Use this file for overo-tobi.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART3 is used by expansion boards to get a tty console. Thus, the
pinmux should be defined by expansion boards, instead of being
imposed by the processor board.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the AT24C01 EEPROM node populated on most Gumstix expansion board.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the timings provided by omap-gpmc-smsc9221. This does not change
the timings, but it avoids code duplication.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some devices (SMSC9217, SMSC9218 and SMSC9221 at least) have better
timings, allowing a higher transfer speed. Create a common file
with these timings.
Performance results with iperf:
- omap-gpmc-smsc911x.dtsi => 54.9 Mbps
- omap-gpmc-smsc9221.dtsi => 92.7 Mbps
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MMC2 is used by the on-board WiFi module populated on some boards
(based on Marvell Libertas 8688 SDIO). The Bluetooth is connected
to UART2.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, overo-related include files are organized as follow:
omap3-overo.dtsi
|
|
omap34xx.dtsi omap3-overo-tobi-common.dtsi omap36xx.dtsi
| | | |
--------------- ---------------
| |
omap3-overo-tobi.dts omap3-overo-storm-tobi.dts
This is unpractical when one has to deal with SoC-specific pinmux
belonging to the omap3_pmx_core2 (defined in omap34xx/omap36xx),
for pins related to the processor board. With the current
hierarchy, such pinmux has to be defined in the expansion board's
.dts, which is not logical.
This patches reorganizes the files to add (yet another) abstraction
layer between the processor and the expansion boards.
omap34xx.dtsi omap3-overo-base.dtsi omap36xx.dtsi
| | | |
--------------- ---------------
| |
omap3-overo.dtsi omap3-overo-storm.dtsi
| |
-------- ------
| omap3-overo-tobi-common.dtsi |
| | | |
--------------- ---------------
| |
omap3-overo-tobi.dts omap3-overo-storm-tobi.dts
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IOMMU DT nodes have been added for the DSP and IPU
subsystems. The MMUs in OMAP5 are identical to those in
OMAP4, including the bus error back capability on IPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the IOMMU nodes for the DSP and IPU subsystems. The MMU
within the IPU sub-system also supports a bus error back
capability, not available on the DSP MMU.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: IPU bus error back addition]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the DT node for the IOMMU within the DSP subsystem. The entry
is disabled to keep in line with the hwmod usage as intended by
the deprecated CONFIG_OMAP_IOMMU_IVA2 flag.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: split the entry and disable the node]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the IOMMU node for the camera subsystem as per the
OMAP IOMMU bindings.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: corrected interrupt number]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch implements a DTS to boot a at91sam9261ek with a dt-enabled
kernel (at91_dt_defconfig).
supported features are:
* dbgu
* lcdc
* usb host
* usb gadget,
* spi dataflash
* nand flash
* touchscreen
* leds
* user buttons
In the TODO list:
* dm9000 (ethernet)
* audio
* mmc
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
