The TSC part allows to specify the input lines. The IIO part assumes
that it usues always the last few, that means if IIO has adc-channels
set to 2 it will use channel 6 and 7. However it might make sense to use
only 6.
This patch changes the device property (which was introduced recently
and was never in an official release) in a way that the user can specify
which of the AIN lines should be used. In Addition to this, the name is
now AINx where x is the channel number i.e. for AIN6 we would have 6.
Prior this, it always started counting at 0 which is confusing. In
addition to this, it also checks for correct step number during reading
and does not rely on proper FIFO depth.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Instead of relying on CONFIG_MEMORY_START for memory
base address, let each romImage board header file
specify this information.
This is reworks code not to rely on CONFIG_MEMORY_START
which in turn is needed for ARCH_MULTIPLATFORM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the ATAGS data structure from head-shmobile.S
since a default ATAGS is already provided by the code
in arch/arm/kernel/atags_parser.c. Passing a NULL as
ATAGS is valid. For actual hardware specific setup
the fixup callback in the board code may be used.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
From Jason Cooper, mvebu fixes for v3.10 round 4:
- mvebu
- fix PCIe ranges property so NOR flash is visible
- kirkwood
- fix identification of 88f6282 so MPPs can be set correctly
* tag 'fixes-3.10-4' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
Signed-off-by: Olof Johansson <olof@lixom.net>
From Alexander Shiyan, this is a series of cleanups of clps711x, movig it
closer to multiplatform and cleans up a bunch of old code.
* clps711x/soc:
ARM: clps711x: Update defconfig
ARM: clps711x: Add support for SYSCON driver
ARM: clps711x: edb7211: Control LCD backlight via PWM
ARM: clps711x: edb7211: Add support for I2C
ARM: clps711x: Optimize interrupt handling
ARM: clps711x: Add clocksource framework
ARM: clps711x: Replace "arch_initcall" in common code with ".init_early"
ARM: clps711x: Move specific definitions from hardware.h to boards files
ARM: clps711x: p720t: Define PLD registers as GPIOs
ARM: clps711x: autcpu12: Move remaining specific definitions to board file
ARM: clps711x: autcpu12: Special driver for handling memory is removed
ARM: clps711x: autcpu12: Add support for NOR flash
ARM: clps711x: autcpu12: Move LCD DPOT definitions to board file
ARM: clps711x: Set PLL clock to zero if we work from 13 mHz source
ARM: clps711x: Remove NEED_MACH_MEMORY_H dependency
ARM: clps711x: Re-add GPIO support
GPIO: clps711x: Add DT support
GPIO: clps711x: Rewrite driver for using generic GPIO code
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
EXYNOS5440 includes both OHCI and EHCI usb host controllers.
This patch adds device tree nodes for both of them. And the
EHCI and OHCI controllers on exynos5440 do not need any
explicit phy configuration. So need to assign a different
compatible value for these controllers.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
G2D node got added twice in exynos4412-smdk4412.dts instead of
getting added to exynos4412-origen.dts. Remove the duplicate entry
and add it to exynos4412-origen.dts.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add pin state information for DP HPD support that requires
pin configuration support using pinctrl interface.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to add vmmc regulator node at MSHC and SDHCI for ODROID-X
board file.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use the standard interrupt-controller and ARM GIC constants to
improve the readability of bcm281xx DT irq properties.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Christian Daudt <csd@broadcom.com>
Replace /include/ by #include for bcm281xx device tree
files, enabling use of the C preprocessor.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Christian Daudt <csd@broadcom.com>
Enable the second PCIe port on QNAP TS-11x/TS-21x devices as newer
revisions (rev 1.3) have a USB 3.0 chip from Etron on PCIe port 1.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
From Simon Horman:
Renesas ARM-based SoC DT updates for v3.11
* Armadillo800eva reference DT - bring up armadillo800eva baord
using DT as much as possible
* Remove unused GIC dtsi entries for r8a7790 and r8a73a4
* Add AS3711 and CPUFreq DT bindings for kzm9g-reference
* Add irqpin DT support for marzen-reference
* tag 'renesas-dt-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: marzen-reference: add irqpin support in DT
ARM: shmobile: kzm9g-reference: add AS3711 and CPUFreq DT bindings
ARM: shmobile: armadillo800eva: Reference DT implementation
ARM: shmobile: Remove unused r8a7790 GIC CPU interface DT bits
ARM: shmobile: Remove unused r8a73a4 GIC CPU interface DT bits
ARM: shmobile: r8a7740: Prepare for reference DT setup
ARM: shmobile: r8a7740: Add OF support to initialze the GIC
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
mvebu pcie driver (kirkwood) for v3.11 (round 2)
- kirkwood
- migrate Netgear ReadyNAS Duo v2 to pcie DT init
* tag 'pcie_kw-3.11-2' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: NETGEAR ReadyNAS Duo v2 init PCIe via DT
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
mvebu dt changes for v3.11 (round 4)
- kirkwood
- reshuffle nodes from kirkwood.dtsi to -6281.dtsi, etc
- add i2c-gpio for km_kirkwood
- add cpu node so pending cpufreq driver will init
* tag 'dt-3.11-4' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood add cpus definition needed by cpufreq driver to dtsi
ARM: kirkwood: add i2c-gpio controller for km_kirkwood
ARM: kirkwood: refactor dtsi to largest common nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
A recent series has added CPU numbers to a lot of dts files,
but unfortunately in a few cases the #address-cells
and #size-cells values are missing, which causes build warnings.
This adds the missing ones for sunxi and sama5 that I found
through build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
ODROID-X board have a max77686 PMIC on i2c channel 0. The properties of used
LDO and BUCK are defined according the schematic.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
RTC is a basic feature of EXYNOS5440. But it was disabled
by issue that comes from EXYNOS5250. (commit id: 522ccdb6)
That issue only applies to EXYNOS5250 not EXYNOS5440. So,
there is no issue with enabled RTC on EXYNOS5440. This
change was tested on EXYNOS5440.
Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These nodes have separately been added to 4212 and 4412 dtsi
files by commit 30269ddff1 ("ARM: exynos: add missing properties
for combiner IRQs"). The existing node also contained a few
incorrect entries.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Keypad pins/lines are board specific and should be added to respective
board dts files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding DWC3 device tree node for Exynos5250 needed to
parse device tree data.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding usb3.0 phy node for Exynos5250 along with the
necessary device data to be parsed.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull ARM fixes from Russell King:
"The biggest two fixes are fixing a compilation error with the
decompressor, and a problem with our __my_cpu_offset implementation.
Other changes are very trivial and small, which seems to be the way
for most -rc stuff."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7747/1: pcpu: ensure __my_cpu_offset cannot be re-ordered across barrier()
ARM: 7750/1: update legacy CPU ID in decompressor cache support jump table
ARM: 7743/1: compressed/head.S: work around new binutils warning
ARM: 7742/1: topology: export cpu_topology
ARM: 7737/1: fix kernel decompressor compilation error with CONFIG_DEBUG_SEMIHOSTING
From Barry Song, SiRF fixes for v3.10 (that we're punting to 3.11):
- Replace include linux/module.h with linux/export.h
- fix a checkpatch issue
- use of_platform_populate instead of of_platform_bus_probe
* tag 'sirf-arm-soc-v3.10-fixes' of git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel:
arm: prima2: use of_platform_populate instead of of_platform_bus_probe
ARM: prima2: fix a checkpatch issue
ARM: prima2: Replace include linux/module.h with linux/export.h
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
From Shawn Guo, imx fixes for 3.10, take 2:
- One device tree fix for all spi node to have per clock added.
The clock is needed by spi driver to calculate bit rate divisor.
The spi node in the current device trees either does not have the
clock or is defined as dummy clock, in which case the driver probe
will fail or spi will run at a wrong bit rate.
- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.
* tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: clk-imx6q: AXI clock select index is incorrect
ARM: dts: imx: fix clocks for cspi
ARM i.MX6q: fix for ldb_di_sels
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Prisk, vt8500 devicetree updates for 3.11.
* tag 'vt8500/dts-3.11' of git://github.com/linux-wmt/linux-vtwm:
dts: vt8500: Correct reference clock on WM8850 SoCs
dts: vt8500: Add ARM, AHB, APB and DDR clock nodes to SoC files
dts: vt8500: Populate missing PLL nodes
dts: clk: vt8500: Update SoC dtsi to use WM8850 PLL clocks
dts: vt8500: Update serial nodes and disable by default in SoC files
dts: vt8500: Add devicetree support for WM8750 SoC and APC8750 board
dts: vt8500: Fix invalid/missing cpu nodes for soc files.
Signed-off-by: Olof Johansson <olof@lixom.net>
Highbank supports SGPIO by bit-banging out the SGPIO signals over
three GPIO pins defined in the DTB. Add support for this SGPIO
functionality.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The ranges DT entry needed by the PCIe controller is defined at the
SoC .dtsi level. However, some boards have a NOR flash, and to support
it, they need to override the SoC-level ranges property to add an
additional range. Since PCIe and NOR support came separately, some
boards were not properly changed to include the PCIe range in their
ranges property at the .dts level.
This commit fixes those platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ranges DT entry needed by the PCIe controller is defined at the
SoC .dtsi level. However, some boards have a NOR flash, and to support
it, they need to override the SoC-level ranges property to add an
additional range. Since PCIe and NOR support came separately, some
boards were not properly changed to include the PCIe range in their
ranges property at the .dts level.
This commit fixes those platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
