This patch adds support for the Linksys WRT1200AC (Caiman) and
the Linksys WRT1900AC v2 (Cobra).
Both boards have:
- 2 Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6176 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 512MB RAM
gregory.clement@free-electrons.com: use serial0:115200n8 in
stdout-path and remove the bootargs part in the chosen node
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch sets display clock correctly. If Display clock isn't set
correctly then you would find below messages and Display controller
doesn't work correctly.
exynos-drm: No connectors reported connected with modes
[drm] Cannot find any crtc or sizes - going 1024x768
Fixes: abc0b1447d ("drm: Perform basic sanity checks on probed modes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge "Third batch of DT changes for 4.2" from Nicolas Ferre:
- USB host clock refine following changes in drivers
- one little fix for usart pinctrl
* tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: remove useless usb clock
ARM: at91/dt: remove useless uhpck clock references from ehci defintions
USB: atmel: update DT bindings documentation
ARM: at91/dt: at91sam9x5: fix usart1 sck pin definition
Merge "ARM: rockchip: dts relicensing for 4.2" from Heiko Stuebner:
Relicense all Rockchip-related devicetree files to the GPL2/X11 combo.
I've now finally aquired necessary Acks from all contributors.
* tag 'v4.2-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: relicense rk3288-evb* under GPLv2/X11
ARM: dts: rockchip: relicense rk3288.dtsi under GPLv2/X11
ARM: dts: rockchip: relicense rk3188-radxarock.dts under GPLv2/X11
ARM: dts: rockchip: relicense rk3066a-bqcurie2.dts under GPLv2/X11
ARM: dts: rockchip: relicense rk3288-thermal.dtsi under GPLv2/X11
ARM: dts: rockchip: relicense rk3188.dtsi under GPLv2/X11
ARM: dts: rockchip: relicense rk3066a.dtsi under GPLv2/X11
ARM: dts: rockchip: relicense rk3xxx.dtsi under GPLv2/X11
Merge "First batch of cleanup for 4.2" from Alexandre Belloni:
- use syscon in the ata and cf drivers to configure the SMC and drop
sam9_smc.c
- switch the at91rm9200 memory controller to syscon
- remove last useless headers
- remove now useless Makefile.boot
* tag 'at91-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
The ohci driver now calls clk_set_rate on the uhpck clock (which forwards
set_rate requests to its parent: the usb clock).
Remove useless references to usb clocks from ohci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The uhpck is useless for High-Speed communications, remove the reference
to this clock in all ehci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds the fixed clocks of external crystal oscillators.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[sboyd@codeaurora.org: Remove size-cells/address-cells]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Merge "Few minimal omap device tree fixes for v4.1-rc series" from Tony Lindgren:
- Disable BeagleBone black RTC-only sleep mode because of hardare
related issues
- Fix NAND on Devkit8000
- Fix WLAN interrupt line on AM335x EVM-SK
* tag 'omap-for-v4.1/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix WLAN interrupt line for AM335x EVM-SK
ARM: dts: omap3-devkit8000: Fix NAND DT node
ARM: dts: am335x-boneblack: disable RTC-only sleep
This adds an initial device tree to run Linux on the Cortex-M4 on
the Vybrid based Colibri VF61 module.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Berlin DT changes for v4.2" from Sebastian Hesselbarth:
- GPLv2/X11 dual licensing
- Mark Berlin DT bindings as unstable
- Updated binding documentation for reworked
chip/system ctrl nodes
* tag 'berlin-dt-4.2-1' of git://git.infradead.org/users/hesselba/linux-berlin:
Documentation: bindings: update the berlin chip and system ctrl doc
Documentation: bindings: move the Berlin clock documentation
Documentation: bindings: move the Berlin pinctrl documentation
Documentation: bindings: move the Berlin reset documentation
Documentation: bindings: update the Berlin controllers documentation
Documentation: bindings: berlin: consider our dt bindings as unstable
ARM: dts: berlin: relicense the BG2CD Google Chromecast dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2cd dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2 Sony NSZ-GS7 dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2 dtsi under GPLv2/X11
ARM: dts: berlin: relicense the BG2Q Marvell DMP dts under GPLv2/X11
ARM: dts: berlin: relicense the berlin2q dtsi under GPLv2/X11
The beaglebone family of boards contain two I2C busses enabled.
The first one with a baseboard identification EEPROM and a
cape I2C bus.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
this patch does the following:
1: adds DT node for fixed oscillator.
2: adds DT node entries for ov2659 sensor
3: adds remote-endpoint entry for VPFE.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
UART3 wakeup takes place with iodaisy chain. enable the wakeup pin.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: tabify uart pins properly while at it]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add voice audio card which is used for telephony on gta04 board.
gtm601 codec is UMTS modem with pcm interface which get samples from
microphone and provide data from other party side. Use simple audio card
to describe audio card.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
uart1 is used for connecting to wilink8 bluetooth subsystem.
add the needed muxes and definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
enable mmc3 used for wlan and uart3 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the technical reference manual for AM35xx system
controller module (SCM) PADCONFS core registers are divided in two
regions: 0x48002030..0x48002268 and 0x480025d8..0x480025fc.
First region is the same for all omap3 SoC and is described in omap3.dtsi.
The second region is the same as in omap34xx (see omap34xx.dtsi)
and omap35xx. The patch adds missing description for the second region.
This patch was tested on AM3517.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While Sitara AM335x SoCs are very close to OMAP SoCs, the 32-line GPIO
controllers are numbered from 0 on AM335x and from 1 on OMAP. But when
the configuration for the TI WLAN controllers was converted from
platform data to device tree, this detail was overlooked, as 10 boards
were using OMAP with the WL12xx and WL18xx controllers, and only one
was based on AM335x.
This invalid configuration prevents the WL1271 module on the AM335x
EVM-SK from notifying interrupts to the SoC, and breaks the wlan driver.
The DTS must be corrected to use the correct GPIO controller.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nand-ecc-opt and device-width properties to enable nand support on
Devkit8000.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: http://bugs.elinux.org/issues/143
Entering RTC-only sleep is only properly supported on early prototypes series
(pre-A6) of the BeagleBone Black. Since rev (A6A), which include all production
versions, it is not support at due to.
(rev A6) enable of the 3v3b regulator moved from LDO2 to LDO4 (3v3a)
side-effect: 3v3b rail remains on in sleep-mode (also in off-mode when battery-powered)
(rev A6A) am335x vdds supply moved from LDO3 to LDO1
side-effect: vdds remains supplied in sleep-mode
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Tested-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LogicPD Torpedo DM3730 devkit consists of a base board and
two processor boards. One of the processor boards has a WLAN and
the other one does not.
Let's set up basic dts file so we can move to device tree only
based booting over next few merge windows. So far I've tested
that UARTs, MMC1, USB OTG, smsc911x, and basic PM support works.
Note that the wireless support in kernel for wl1283 seems to be
broken, it tries to load wl127x-nvs.bin instead of wl128x-nvs.bin
with firmware.
Cc: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "The i.MX fixes for 4.1, 2nd round" from Shawn Guo:
- Fix i.MX27 FEC register map which overlaps the SCC (Security
Controller) register space.
- Fix i.MX27 DTB build rule which was wrongly controlled by i.MX31
option.
* tag 'imx-fixes-4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: fix imx27 dtb build rule
ARM: dts: imx27: only map 4 Kbyte for fec registers
The at91rm9200 memory controller is not simply an SDRAM controller. It also
controls the EBI (External Bus Interface), the SMC (Static Memory Controller)and
the Burst Flash Controller.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The i.MX27 dtb build should be controlled by CONFIG_SOC_IMX27 rather
than CONFIG_SOC_IMX31.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fixes: cb612390e5 ("ARM: dts: Only build dtb if associated Arch and/or SoC is enabled")
Cc: <stable@vger.kernel.org>
Add vcc_mmc1 fixed regulator to remove the 'no vmmc regulator found' warning
when probing the mmc1 device.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add fixed regulator for vmmc0 and attach the vmmc for it to the mmc0
node on the SAM5D3 Xplained board. This will remove the following
warning from the kernel:
atmel_mci f0000000.mmc: No vmmc regulator found
Note, atmel_defconfig will need fixed regulator support enabled if this
is to be used properly.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[use a fixed regulator instead of gpio one]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The SAM5D3 Xplained device tree is missing the vqmmc node which is
tied to 3.3V on the board. Add this to avoid the kernel warning that
there is no vqmmc node.
atmel_mci f0000000.mmc: No vqmmc regulator found
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The mmc1 channel is not populated on the SAM5D3 Xplained board, however
it is enabled and therefore the driver is attaching to it.
The node configuration for mmc1 is missing, so add an mmc1 node in the
device tree and set its status to disabled. Also add the vmmc and the
necessary slot configuration if this node were enabled to avoid the following
warnings from the driver:
atmel_mci f8000000.mmc: No vmmc regulator found
atmel_mci f8000000.mmc: No vqmmc regulator found
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
commit 111573ccd8 ("mtd: atmel_nand: check NFC busy flag by HSMC_SR
instead of NFC cmd regs")
check NFC busy by nfc SR instead of NFC cmd regs. So we don't need to
map NFC cmd registers to include NFCBUSY bit.
That means we only need map 0x08000000 instead of 0x10000000 for NFC
cmd regs.
This patch reduce the NFC cmd regs map for sama5d3 & sama5d4.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Update the pinctrl ranges property to support pioD controller whose
mapping is not contiguous with other pio controllers. Without this
update, getting resource will fail, then pinctrl probe will fail too
because there is a missing pio controller.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
