Currently none of the target boards nor the driver supports
IR TX. However this pin is used in a few instances as a GPIO.
Split the pin ctrl descriptions so that only the IR RX is
configured to be used.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Whereas for Armada 370 and XP the main PLL frequency was 2GHz for the
Armada 375, 38x and 39x, the frequency is 1GHz. When writing support
for these last SoCs, there was no official value for the PLL. Now that
we have it, this patch fixes it in the device tree.
This value is currently only used by the NAND driver for the setting
the NAND timing. Fortunately it is not actually used: all the mainline
board with a NAND flash comes with a NAND device tree node using the
"marvell,nand-keep-config" property. With this property the timings
are not modified in the kernel driver and are kept from the
bootloader.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marcin Wojtas <mw@semihalf.com>
The adv7511 IRQ is low level triggered, not falling edge triggered. The
wrong sense configuration results in no interrupt being triggered at
all, breaking hotplug detection. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Fixes: 83a0731b39 ("ARM: shmobile: koelsch: Add DU HDMI output support")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the miphy28lp is upstream, we can add the sata dt nodes
for stih407 family silicon. This has been tested on b2120 board
J4 (sata0 channel). These nodes are disabled by default as a
special mini pci-e to sata daughter board is required which
isn't shipped with the board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This will avoid programming the retime registers when not implemented
- PIO5 : no retime registers assigned to pins 6 and 7
- PIO35 : pin 7 is reserved so no retime register assigned to it
Signed-off-by: Karim BEN BELGACEM <karim.ben-belgacem@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
On current ST platforms the LPC controls a number of functions. This
patch enables support for the LPC Watchdog and LPC RTC devices on LPC1
and LPC2 respectively.
Signed-off-by: David Paris <david.paris@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The nodes have been split to allow as much commonality as possible.
The stih407 has a silicon bug with eMMC UHS modes (with top regs)
and as such doesn't have any of the uhs dt properties.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The MK808C is an A20 based android stick, with 1G RAM, 8G NAND flash,
a RTL8723au wifi + bt combo chip, a USB host ports using USB-A receptacles,
a mini USB-B receptacle for USB OTG, mini HDMI and a TRS connector for AV.
This patch adds basic support for the device, more information can be found
here (http://linux-sunxi.org/MK808C).
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Synchronous Serial Controller is used to provide SPI.
These are the ports which are located on the Stand-By Controller (SBC).
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
It should be the first controller, not the second. The indexes of the
usb resets were also wrong and have been fixed.
The issue was caused by the changes in 308efde ("ARM: tegra: Add resets
& has-utmi-pad-registers flag to all USB PHYs") being misapplied by git
due to the patch context being insufficient.
This broke USB after 6261b06 ("regulator: Defer lookup of supply to
regulator_get"), because it changed the order in which the controllers
were probed.
The fix for this issue was suggested by Mikko Perttunen and Tuomas
Tynkkynen.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Cc: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The pinctrl-assert-gpios is an invalid pinctrl property. It was
probably sneaked from vendor tree. Remove it.
Fixes: 4e18a2243a ("ARM: imx6qdl-sabreauto.dtsi: add max7310 support")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable perf events on msm8660 devices by adding the pmu node.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add configuration nodes for following devices:
* GPIO block, with 22 pins
* MPP block, with 8 pins
* Volatage ADC (VADC), with multiple inputs
* Thermal sensor device, which is using on chip VADC
channel report PMIC die temperature.
* RTC device
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add configuration nodes for following devices:
* GPIO block, with 36 pins
* MPP block, with 8 pins
* Current ADC (IADC)
* Volatage ADC (VADC), with multiple inputs
* Thermal sensor device, which is using on chip VADC
channel report PMIC die temperature
* Power key device, which is responsible for clean system
reboot or shutdown
* White LED device
* RTC device
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add configuration nodes for multi purpose pins and
thermal sensor devices. Thermal sensor will report
PMIC die temperature.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
I2C1 pinctrl is not really specific to a board, moving to SOC dtsi would
avoid redefining this in every board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds USB OTG support on USB1 for Compulab QS-600 Board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[Srinivas Kandagatla: fixed up regulators and status properties]
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds device tree nodes to support two usb hosts on Compulab QS600 board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[Srinivas Kandagatla: fixed up regulators and status properties]
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds AHCI based SATA controller support to APQ8064.
Tested on IFC6410 board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds USB OTG support on USB1 of APQ8064 SOC.
Tested on IFC6410 with ethernet gadget.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This patch adds support to basic regulators wiredup on IFC6410 board.
All these regulators are tested as part of USB, SATA and HDMI.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add properties for dwc2 usb device controller according to
Documentation/devicetree/bindings/usb/dwc2.txt
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The fixed-regulator bindings require a separate property enable-active-high,
the standard gpio phandle property polarity setting is ignored.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: 4fe69a934b ("ARM: dts: Add Phytec pfla02 with i.MX6 DualLite/Solo")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The dr_mode of usb0 on imx233-olinuxino is left to default "otg".
Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the
same pin as USB_OTG_ID it's possible to disable USB host by LED toggling:
echo 0 > /sys/class/leds/green/brightness
[ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1
[ 1068.890000] usb usb1: USB disconnect, device number 1
[ 1068.920000] usb 1-1: USB disconnect, device number 2
[ 1068.920000] usb 1-1.1: USB disconnect, device number 3
[ 1069.070000] usb 1-1.2: USB disconnect, device number 4
[ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered
[ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11
This patch fixes the issue by setting dr_mode to "host" in the dts file.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Fixes: b493129482 ("ARM: dts: imx23-olinuxino: Add USB host support")
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The tsadc is used to read cpu and gpu temperatures. Also enable it on the
other rk3288 boards beside the evb using the cru reset settings.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We defined bindings for the supply handling of act8846 regulators now, so
describe those on the firefly too.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Specifying these rails should eventually let us do UHS.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the dts node for the PMU with the correct PMUIRQ interrupts
for each core.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There is no crystal connected to the internal RTC on the Open Block
AX3. So let's disable it in order to prevent the kernel probing the
driver uselessly. Eventually this patches removes the following
warning message from the boot log:
"rtc-mv d0010300.rtc: internal RTC not ticking"
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8 +
