Add the interrupts property to all the 13 mailbox nodes in
DRA7xx. The interrupts property information added is inline
with the expected values with the DRA7xx crossbar driver,
and is common to both DRA74x and DRA72x SoCs.
Do note that the mailbox 1 is only capable of generating out
3 interrupts, while all the remaining mailboxes have 4
interrupts each.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the datasheet, the operating clock for IIC0 is the HPP
(RT Peri) clock, not the SUB (Peri) clock. Both clocks run at the same
speed (50 Mhz).
This is consistent with IIC0 being located in the A4R PM domain, and
IIC1 in the A3SP PM domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Merge "Nomadik updates for the v3.19 series" from Linus Walleij:
Nomadik changes for the v3.19 development series:
- Rearrange the DTS files to make a pure SoC-specific file and
a pure board file for S8815.
- Add the device tree for the NDK15 board.
- Update the defconfig and configure in the STMPE expander by
default on the Nomadik.
* tag 'nomadik-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: configure in STMPE support
ARM: update Nomadik config
ARM: nomadik: device tree for NHK15 board
ARM: nomadik: push ethernet down to board
ARM: nomadik: set up MCDATDIR2
ARM: nomadik: move GPIO I2C to S8815 board file
ARM: nomadik: disable chrystals in top level board files
ARM: nomadik: move MMC/SD card detect GPIO to board DTS
Signed-off-by: Olof Johansson <olof@lixom.net>
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "at91: dt for 3.19 #1" from Nicolas Ferre:
"Very little DT update for AT91. More will come but I want to send this first
batch soon so it doesn't get in the way of larger modifications."
First DT batch for 3.19:
- CAN device nodes for at91sam9263 and at91sam9x5
- at91sam9x5 DMA definitions for usart
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: at91sam9263: Add CAN device nodes
ARM: at91/dt: at91sam9x5: Add CAN device nodes
ARM: at91/dt/trivial: at91sam9x5_can.dtsi: comment and whitespace fixes
ARM: at91: at91sam9x5 dt: add usart dma definitions to dt
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Ux500 core changes for v3.19" from Linus Walleij:
"please pull in these Ux500 core changes for this kernel development
cycle: mainly a generic power domain implementation from Ulf Hansson
that needs to get queued up in -next and tested."
Generic power domains for the Ux500
* tag 'ux500-core-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Add i2c devices to the VAPE PM domain
ARM: ux500: Add spi and ssp devices to the VAPE PM domain
ARM: ux500: Add sdi devices to the VAPE PM domain
ARM: ux500: Add DT node for ux500 PM domains
ARM: ux500: Enable Kconfig for the generic PM domain
ARM: ux500: Initial support for PM domains
dt: bindings: ux500: Add header for PM domains specifiers
dt: bindings: ux500: Add documentation for PM domains
ARM: u300: Convert pr_warning to pr_warn
Merge "ARM: berlin: DT changes for v3.19 (round 1)" from Sebastian Hesselbarth:
"This is Berlin DT changes for v3.19 and contains those patches that missed
the v3.18 merge window plus corresponding patches to catch-up with Antoine's
BG2Q improvements for BG2 and BG2CD. We now have working SDHCI and Ethernet
on all SoCs (well, BG2CD has HDMI HEC only), SATA PHY support for BG2 is still
pending."
Berlin DT changes for v3.19 (round 1)
- AHCI and SATA PHY nodes for BG2Q
- Reset controller binding docs
- Ethernet nodes for BG2, BG2CD
- SDHCI nodes for BG2, BG2CD
- Corresponding board changes to enable AHCI, Ethernet, SDHCI
* tag 'berlin-dt-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: Enable eMMC on Sony NSZ-GS7
ARM: dts: berlin: Enable WiFi on Google Chromecast
ARM: dts: berlin: Add SDHCI controller nodes to BG2/BG2CD
ARM: dts: berlin: Enable ethernet on Sony NSZ-GS7
ARM: dts: berlin: Add phy-connection-type to BG2Q Ethernet
ARM: dts: berlin: Add BG2CD ethernet DT nodes
ARM: dts: berlin: Add BG2 ethernet DT nodes
ARM: dts: berlin: Add GPIO leds to Google Chromecast
ARM: dts: berlin: enable timer 1 for sched_clock
ARM: dts: berlin: add a required reset property in the chip controller node
Documentation: bindings: add reset bindings docs for Marvell Berlin SoCs
ARM: dts: berlin: enable the eSATA interface on the BG2Q DMP
ARM: dts: berlin: add the AHCI node for the BG2Q
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Broadcom Cygnus SoC Device Tree changes" from Florian Fianelli:
This patchset contains initial support for Broadcom's Cygnus SoC based on our
iProc architecture. Initial support is minimal and includes just the mach
platform code, clock driver, and a basic device tree configuration. Peripheral
drivers will be submitted soon, as will device tree configurations for other
Cygnus board variants.
These are the Device Tree changes
* tag 'arm-soc/for-3.18/cygnus-dts-v9' of http://github.com/brcm/linux:
ARM: dts: Enable Broadcom Cygnus SoC
dt-bindings: Document Broadcom Cygnus SoC and clocks
Signed-off-by: Olof Johansson <olof@lixom.net>
The dma controller requires that the ahb1 bus clock be driven by pll6
for peripheral access to work. Previously this was done in the dma
controller driver, but was since removed as part of a series to unify
the ahb1_mux and ahb1 clock drivers, in
14e0e28 dmaengine: sun6i: Remove obsolete clk muxing code
Unfortunately the rest of that series did not make it, leaving us with
broken dma on sun6i.
This patch reparents ahb1_mux to pll6 using the DT assigned-clocks
properties in the dma controller node.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Support for the 2 PTMs, 3 ETMs, funnel, TPIU and replicator
connected to the ETB are included. Proper handling of the
ITM and the replicator linked to it along with the CTIs
and SWO are not included.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Roman Byshko <rbyshko@gmail.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
The 370 rd has a 7 port, mv88E6182 switch, connected to eth1. Add a
fixed-link subnode to the ethernet device tree node, to force
gigabit/full duplex. Add a dsa node, with describing the four used
ports. This requires adding an alias to the mdio node, so it can be
referenced as a phandle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1415214121-29286-3-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit modifies the Armada 370 and Armada 370 DB Device Tree
descriptions to use the simple-card DT binding to describe the audio
complex of the Armada 370 DB instead of a custom audio machine driver.
To do so, it:
- Adds the sound-dai-cells properties to the CS42L51 node, the audio
controller node and the SPDIF in/out nodes.
- Completely changes the description of the sound complex to use the
"simple-audio-card" DT binding instead of the
"marvell,a370db-audio" DT binding.
- Fixes the indentation to properly use tabs instead of spaces.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-6-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Back when audio was enabled, the muxing of some MPP pins was causing
problems. However, since commit fea038ed55 ("ARM: mvebu: Add proper
pin muxing on the Armada 370 DB board"), those problematic MPP pins
have been assigned a proper muxing for the Ethernet interfaces. This
proper muxing is now conflicting with the hog pins muxing that had
been added as part of 249f382250 ("ARM: mvebu: add audio support to
Armada 370 DB").
Therefore, this commit simply removes the hog pins muxing, which
solves a warning a boot time due to the conflicting muxing
requirements.
Fixes: fea038ed55 ("ARM: mvebu: Add proper pin muxing on the Armada 370 DB board")
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1414512524-24466-5-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add SDHCI node for supporting the micro SD card. On Trats2 board the
SDHCI does not use sd2_cd pins (gpk2-2) for card detect but gpx3-4
instead.
Power is supplied from LDO21 regulator which in off state is controlled
by external GPIO pin.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds new exynos4415.dtsi to support Exynos4415 SoC
based on Cortex-A9 quad cores and includes following dt nodes:
- GIC interrupt controller (GIC-400)
- Pinctrl to control three GPIO parts
- CMU (Clock Management Unit) for CMU/CMU_DMC/AUDSS
- CPU information (Cortex-A9 quad cores)
- UART to support serial port
- MCT (Multi Core Timer)
- ADC (Analog Digital Converter)
- RTC (Real Time Clock)
- I2C/SPI busses
- Power domains (CAM, TV, MFC, G3D, LCD0, ISP0/1)
- PMU (Performance Monitoring Unit)
- MSHC (Mobile Storage Host Controller)
- EHCI (Enhanced Host Controller Interface)
- OHIC (Open Host Controller Interface)
- USB 2.0 device with hsotg
- PWM (Pluse Width Modulation) Timer
- AMBA bus for PDMA0/1
- SYSRAM node for memory mapping
- SYSREG node for memory mapping
- PMU (Power Management Unit) node for memory mapping
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
[m.szyprowski: Add OHCI node and correct EHCI node]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[yj44.cho: Add mipi-phy node]
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
[jaewon02: Add EHCI and SPI_2 node]
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
[ideal.song: Add I2S0 node for audio interface]
Signed-off-by: Inha Song <ideal.song@samsung.com>
[tomasz.figa: Add L2 cache node]
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add sleep mode pin configuration using pinctrl subsystem
to reduce leakage power-consumption of gpio pin in sleep state.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for device tree source for Samsung Rinato
board (Gear 2) based on Exynos3250 SoC.
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- MFC of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The 5th NAND partition should be named "NAND.u-boot-spl-os"
instead of "NAND.u-boot-spl". This is to be consistent with other
TI boards as well as u-boot.
Fixes: 91994facdd ("ARM: dts: am335x-evm: NAND: update MTD partition table")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device nodes for the VOP iommus.
Device nodes for other iommus will be added in later patches.
The iommu nodes use the #iommu-cells property as described in:
Documentation/devicetree/bindings/iommu/iommu.txt
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Looks like we're still missing the keypad map for EVM.
Let's add it since we have the binding now available
for the twl4030_keypad as otherwise we get the following
errors during the boot:
twl4030_keypad keypad.31: OF: linux,keymap property not defined
in /ocp/i2c@48070000/twl@48/keypad
twl4030_keypad keypad.31: Failed to build keymap
twl4030_keypad: probe of keypad.31 failed with error -2
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we're still missing the keypad map for LDP.
Let's add it since we have the binding now available
for the twl4030_keypad as otherwise we get the following
errors during the boot:
twl4030_keypad keypad.31: OF: linux,keymap property not defined
in /ocp/i2c@48070000/twl@48/keypad
twl4030_keypad keypad.31: Failed to build keymap
twl4030_keypad: probe of keypad.31 failed with error -2
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the following warning during the boot:
mtd: partition "Filesystem" extends beyond the end of device
"omap2-nand.0" -- size truncated to 0x6000000
Looks like I got the last partition size wrong while setting
up the .dts file. Note that this does not affect the partition
as the size has been getting truncated to the right size.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jonathan writes:
First round of new drivers, features and cleanups for IIO in the 3.19 cycle.
New drivers / supported parts
* rockchip - rk3066-tsadc variant
* si7020 humidity and temperature sensor
* mcp320x - add mcp3001, mcp3002, mcp3004, mcp3008, mcp3201, mcp3202
* bmp280 pressure and temperature sensor
* Qualcomm SPMI PMIC current ADC driver
* Exynos_adc - support exynos7
New features
* vf610-adc - add temperature sensor support
* Documentation of current attributes, scaled pressure, offset and
scaled humidity, RGBC intensity gain factor and scale applied to
differential voltage channels.
* Bring iio_event_monitor up to date with newer modifiers.
* Add of_xlate function to allow for complex channel mappings from the
device tree.
* Add -g parameter to generic_buffer example to allow for devices with
directly fed (no trigger) buffers.
* Move exynos driver over to syscon for PMU register access.
Cleanups, fixes for new drivers
* lis3l02dq drop an unneeded else.
* st sensors - renam st_sensors to st_sensor_settings (for clarity)
* st sensors - drop an unused parameter from all the probe utility
functions.
* vf610 better error handling and tidy up.
* si7020 - cleanups following merge
* as3935 - drop some unnecessary semicolons.
* bmp280 - fix the pressure calculation.
Driver has been there since a while back, but the dts never seems to
have been updated with the node (nor pinctrl). Do so now.
Cc: Matt Porter <mporter@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
When booting omap3 in device tree mode, we're currently getting
the following errors:
omap_l3_smx omap_l3_smx.0: couldn't request debug irq
omap_l3_smx: probe of omap_l3_smx.0 failed with error -22
This is because we don't have handling in the driver for the
compatible property and instead assume platform data being
passed.
Note that this binding is already documented, and implemented
for the related omap_l3_noc driver for omap4 and later. Looks
like the binding somehow never got never implemented for this
omap_l3_smx driver though.
Let's also remove __exit_p to allow binding and unbinding
of the driver while at it.
Reported-by: Pavel Machek <pavel@ucw.cz>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Instead of using the ADC_PHY register base address, use sysreg phandle
in ADC node to control ADC_PHY configuration register.
This patch adds syscon node for Exynos3250, Exynos4x12, Exynos5250,
and Exynos5420, Exynos5800.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
To: linux-samsung-soc@vger.kernel.org
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
