In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses. However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.
This patch corrects the references for the affected dts files.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove all remaining uses of gpmc,device-nand that have been added since
the property was removed by commit f40739faba ("ARM: dts: OMAP2+:
Simplify NAND support").
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong documentation in pinmux description can be especially confusing.
Keep it proper.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The USB3 PHY driver (ti-pipe3) was updated so that the relevant
clock phandles are expected in the DT node.
Provide the necessary clocks.
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: Rob Landley <rob@landley.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
[nicolas.ferre@atmel.com: add new at91sam9261 & at91sam9rl]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
If without the MICBIAS routing, the record don't work.
Add the missing MICBIAS routing to let record from mic working.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the sama5d3 dtsi file in go into mainline before sound driver,
and, the sound compatible string is changed when go into mainline.
Add this patch to correct the sound compatible string.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The real polarity of the LEDs is inversed. The led is between 3.3v and the PWM.
It was working before because the driver was getting the duty cycle calculation
wrong.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes the compatible string, adds the pinmuxing for the ADC pins.
Also, removes atmel,adc-use-external-triggers as it is not possible to remove it
unless redefining the whole adc node
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This adds support for:
- SPI
- Dataflash
- LCD
- i2c
- ADC
- Touchscreen
- USB gadget
- PWM
Also it switches the ds1 and ds2 leds to PWM control.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds support for the ADC, LCD, USB gadget and PWM controllers to the
at91sam9rl. It also reorders the pinctrl_spi0 as it was not correctly sorted.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
VDDIO_SDMMC3 is the VQMMC (I/O) supply, not the VMMC (core) supply,
for the SD slot on Venice2.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This regulator supplies power to pretty much everything on the board, so
it doesn't make sense to allow it to turn off. Mark it boot-on and
always-on so it doesn't get turned off. Without this, I see issues with
the eMMC device; it can't be correctly detected during boot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Regulator vddio_sdmmc3 provides the Tegra<->SD IO voltage, not the card
core supply voltage. That is, it provides vqmmc, not vmmc. Fix the DT to
correctly reflect this.
Reported-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
These are mostly identical to the Venice2 regulator definitions, since
the board designs are very similar. Differences are:
- Jetson TK1 doesn't have a built-in LCD panel, so on-board regulators
are not present for the backlight, touchscreen, or panel.
- +3.3V_RUN needs to be boot-on/always-on, since it's widely used. This
change should likely be propagated to Venice2 for completeness,
although it will have no practical effect there since various other
regulators use +3.3V_RUN as their supply and are always-on.
- +3.3V_LP0 needs to be boot-on as well as always-on. One reason
is because it's used to driver the UART level-shifter; without this, I
see a brief period of UART corruption during cold boots.I suspect this
change needs to be propagated to Venice2, and we simply haven't noticed
the need since there's no UART level-shifter on Venice2.
- A few rails have different names in the schematics.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Jetson TK1 is an NVIDIA Tegra124 development board, containing Tegra124,
2GB RAM, eMMC, SD card, SPI flash, serial port, PCIe Ethernet, HDMI,
audio, mini PCIe, JTAG, SATA, and an expansion IO connector containing
GPIOs, I2C, SPI, CSI, eDP, etc.
The following features work with this device tree: UART, SD card, eMMC,
SPI flash, USB (full-size jack, and mini-PCIe), audio, AS3722 RTC, system
power-off, suspend/resume (LP1) with wake via RTC alarm.
The following features should work with this device tree, but are not
validated: Expansion I2C, expansion SPI, expansion GPIO, gpio-key for the
power button.
The following features are not yet implemented in this device tree: Most
voltage regulators, expansion UART, HDMI, eDP, PCIe (Ethernet, and mini-
PCIe connector), CSI, SATA.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The default behaviour of the uart-rx pins on the rk3188 is to be pulled up and
a lot of designs use diodes to even prevent them from being raised from the
outside.
Therefore change the rx-pin settings accordingly.
This also fixes a uart receive problem on mass production Radxa Rock boards.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix typo of renesas,groups in the koeslch dt. The kernel has no
renesas,gpios but this should match renesas,groups.
Noticed thanks to similar fix for Lager by Rob Taylor and Ben Dooks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the clock controller itself, the xti clock on the smdk2416
as well as the clock references in the individual device nodes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Allwinner reworked the PLL4 clock in sun7i; so we need to change the
compatible. Additionally, PLL8 is compatible with this new PLL4
implementation, so let's add a node for it as well.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The prcm lives at address 0x01f01400 as the reg entry in its node already
correctly indicates, rename the node to match this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The correct binding is "micrel,led-mode", not "led-mode".
This corrects an error which was introduced when setting of ethernet PHY
LED mode was added by 82e62182d59bd1d0 ("ARM: shmobile: lager: Set ethernet
PHY LED mode").
This makes the lager code consistent with the koelsch code which was added
by ae00d12a032490b3 ("ARM: shmobile: koelsch: Set ethernet PHY LED mode").
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
