Merge "LPC18xx DTS changes for 4.3" from Joachim Eastwood:
This patch set adds DT nodes for all the drivers that went upstream in
4.2 and should represent the bulk of DTS changes for 4.3. All nodes
added are documented and some of patches carries a ack from subsystem
maintainer. It also features updates to the EA4357 dev- kit and a new
board from Ezequiel Garcia.
Note that there might be one more batch of DTS changes for 4.3 if any
new drivers goes upstream and also some changes for the Hitex eval board
might come.
* 'lpc18xx_43xx_dts_4.3' of https://github.com/manabian/linux-lpc:
ARM: dts: add DT for CIAA LPC4337 industrial computer
of: add vendor prefix for CIAA project
ARM: dts: lpc4357-ea4357: add uart3
ARM: dts: lpc4357-ea4357: add ethernet
ARM: dts: lpc4357-ea4357: add gpio joystick
ARM: dts: lpc4357-ea4357: add mmcsd
ARM: dts: lpc4357-ea4357: add pinctrl and uart0 muxing
ARM: dts: lpc18xx: add usb nodes
ARM: dts: lpc18xx: add ethernet node
ARM: dts: lpc18xx: add creg (syscon) node
ARM: dts: lpc18xx: add mmcsd node
ARM: dts: lpc18xx: add can nodes
ARM: dts: lpc18xx: add ssp nodes
ARM: dts: lpc18xx: add gpio node
ARM: dts: lpc18xx: add pinctrl node
ARM: dts: lpc18xx: add uart new compat string and clk names
ARM: dts: lpc18xx: add cgu and ccu clock-controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that PCIe DT binding is disabled in SoC specific DTS,
we need a way to override it in a board specific DTS. So
rename the PCIe nodes accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Currently PCIe DT bindings are broken. PCIe driver can't function
without having a SerDes driver that provide the phy configuration.
On K2E EVM, this causes problem since the EVM has Marvell SATA
controller present and with default values in the SerDes register,
it seems to pass the PCIe link check, but causes issues since
the configuration is not correct. The manifestation is that when
EVM is booted with NFS rootfs, the boot hangs. We shouldn't enable
PCIe on this EVM since to work, SerDes driver has to be present as
well. So by default, the PCIe DT binding should be disabled in SoC
specific DTS. It can be enabled in the board specific DTS when the
SerDes device driver is also present.
So fix the status of PCIe DT bindings in the SoC specific DTS to
"disabled". To enable PCIe, the status should be set to "ok" in
the EVM DTS file when SerDes driver support becomes available in
the upstream tree.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The rk3288 uses spi irqs for the arm-pmu on individual cpu cores, so needs
the affinity to them defined.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
The memory node is supposed to contain a device_type property marking
it as memory. The currently included boards miss this property.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
While pinky was one of the earlier development models, is on the list
of endangered species today and nearly extinct, I want to keep mine
around for the foreseeable future after spending all the time making a
nice hole into the base below the dut-connector.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the shared devicetree files for the Veyron device family.
They are split, as not all veyron devices are chromebooks and
not all contain a sd-card slot.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Merge "omap dts changes for v4.3, part 1" from Tony Lindgren:
Omap dts changes for v4.3 merge window. There are also related
changes for reemoteproc platform_data and audio options for
omap2plus_defconfig to keep audio working when changing boards
to use SIMPLE_CARD. The summary of changes is:
- A large set of audio related changes for SIMPLE_CARD from
Peter Ujfalusi <peter.ujfalusi@ti.com> for am335x and am437x
- Pinctrl dts defines for dra7 virtual mode to configure timings
- Change to use cpsw slave0 for dra7 Ethernet
- Remove unconfigured and wrong l3-mux entry for dm816x
- Add support for Gumstix Palo35 and TobiDuo boards, and Overo
PoP NAND and McBSP2
- Start using new HDMI binding for tilcdc
- Start using new sDMA crossbar for dra7
- Start using rproc for am335x and am437x M3 coprocessor
* tag 'omap-for-v4.3/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (32 commits)
ARM: dts: am335x-evm: Switch using simple-audio-card for audio support
ARM: dts: am335x-evm: Add sleep pin settings for mcasp1
ARM: dts: am335x-evm: Rename pinctrl section for McASP1
ARM: dts: am335x-evm: Fix mcasp1 node's indentation
ARM: dts: am335x-evmsk: Switch using simple-audio-card for audio support
ARM: dts: am335x-evmsk: Add sleep pin settings for mcasp1
ARM: dts: am335x-evmsk: Fix mcasp1 node's indentation
ARM: dts: am437x-gp-evm: Enable analog audio via simple-card
ARM: dts: am437x-gp-evm: McASP1 node for audio support
ARM: dts: am437x-gp-evm: Add node for tlv320aic3106 audio codec
ARM: dts: am437x-gp-evm: Rename fixed regulator vmmcsd_fixed to evm_v3_3d
ARM: dts: am437x-gp-evm: Add gpio-hog for configuring the display/audio mux
ARM: dts: am43xx-epos-evm: Enable analog audio via simple-card
ARM: dts: am43xx-epos-evm: Add node for tlv320aic3111 audio codec
ARM: dts: am43xx-epos-evm: McASP1 node for audio support
ARM: dts: am43xx-epos-evm: Add regulator for VBAT and DCDC4 of tps65218
ARM: dts: am43xx-epos-evm: Add gpio-hog for configuring the display/audio mux
ARM: dts: am437x-sk-evm: Switch using simple-audio-card for audio support
ARM: dts: am437x-sk-evm: Add sleep pin settings for mcasp1
ARM: omap2plus_defconfig: Enable audio related config options
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch creates a sbs-battery fragment for batteries connected
to the i2c tunnel of the cros-ec embedded controller.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Douglas Anderson <dianders@chromium.org>
Fixes for omaps, all dts changes except for one:
- Fix up LCD panel name for overo boards
- Three fixes for pepper board for regulators, freqeuncy
scaling and audio input. Note that there is still one
issue being worked on for booting with multi_v7_defconfig
- Add missing #iommu-cells for omap4 and 5
- Add missing HAVE_ARM_SCU for am43xx
* tag 'omap-for-v4.2/fixes-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (210 commits)
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
ARM: dts: omap3: overo: Update LCD panel names
+ Linux 4.2-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
Audio-in was incorrectly routed to Line In. It should be Mic3L as per
schematic.
Using mic-bias voltage at 2.0v (<0x1>) does not work for some reason. There
is no voltage seen on micbias (R127). Mic-bias voltage of 2.5v (<0x2>) works.
I see voltage of 2.475v across GND and micbias.
With these changes, I can record audio with a pair of proliferate TRRS earbuds.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Acked-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "ARM: imx: fixes for 4.2" from Shawn Guo:
The i.MX fixes for 4.2:
- Correct compatible string for i.MX27 GPT which actually shares the
same programming model as i.MX21 GPT rather than i.MX1 one.
- Add missing #io-channel-cells property for i.MX23 LRADC device, which
is required for the device to be an IIO provider.
- Correct HSYNC/VSYNC pins and add ddc-i2c-bus property for TVE device
on imx53-qsb to work properly.
- Always enable PU domain if CONFIG_PM is not set. This fixes a couple
of failure scenarios which will hang the system if one of the devices
in the PU domain is accessed.
* tag 'imx-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
ARM: dts: imx53-qsb: fix TVE entry
ARM: dts: mx23: fix iio-hwmon support
ARM: dts: imx27: Adjust the GPT compatible string
Signed-off-by: Olof Johansson <olof@lixom.net>
Both imx53-qsb and imx53-qsrb don't have external pull-up resistors
on the I2C1 SCL and SDA lines populated. Select open-drain mode and
enable the internal pull-up for both.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This commit extends the existing Vybrid I2C support to cover buses i2c1,
i2c2, and i2c3. Based in (very) large part on an initial patch by
Stefan Agner that was just lacking a couple of DMA assignments.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add HDMI support. As the DDC I2C pins are not connected due to
pin conflicts, we do not pass the 'ddc-i2c-bus' property in
this case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
UHS-I support is available on Ventana boards with micro-SD sockets depending
on the board revision. To support this pinctl states for 100Mhz and 200MHz
must be added as well as pinmux of the VSELECT signal. In order to support
UHS-I the I/O rail of the 4-bit data bus must be switchable between 1.8V
and 3.3V.
By adding the no-1-8-v property, which disables UHS-I support, we allow the
bootloader to be in charge of selecting which boards have this capability
by removing that property if the board model/revision implement the support.
Additionally we will remove NANDF_CS1 here from the nand pinmux group as the
second chip-select is not used on any ventana boards and this is the pad
that is used for SD3_VELECT.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This board is used in some TV-boxes like for example the Beelink R89 or
Tronsmart R28.
The board itself follows the reference design for the most part. But
there are no schematics available it seems, so some things should be
taken with a grain of salt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Romain Perier <romain.perier@gmail.com>
Add basic support for CIAA (Argentine Open Industrial Computer)
LPC4337 board. This commit enables the following peripherals:
* UART
* SSP
* Ethernet
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use mcasp1_pins as name for the pinctrl section needed for McASP1 instead
of the am335x_evm_audio_pins name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses McASP1 <-> tlv320aic3106 for analog audio and has
Headphone out and Line in connectors.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The same regulator is used by other chips on the board. The power path is:
VBAT -> TPS63031 - Enable signal is V1_8D regulator -> V3_3D.
V3_3D is used by SD slot and tlv320aic3106 codec as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO5_8 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use simple card for audio support on ePOS-EVM.
The audio on the board is: McASP1 <-> tlv320aic3111 codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VBAT and DCDC4 regulator is needed for audio support (tlv320aic3111)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO2_1 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card".
Also enable the Line-In route as the board has support for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
