This enables tca6424a GPIO expander driver that in turn enables
TPD12S015 HDMI ESD protection and level shifter on OMAP5 uevm.
In other words, it makes HDMI work on OMAP5 uevm.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One of the lines from PCF857x is connected to the vdd line of MMC1
in DRA74x and DRA72x EVMs and is modelled as a regulator. If PCF857x
is not made as built-in, the regulator_get in omap_hsmmc fails making
it difficult to use MMC1 as rootfs.
Make PCF857x built-in.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
PBIAS regulator is required for MMC module in OMAP2, OMAP3, OMAP4,
OMAP5 and DRA7 SoCs. Enable it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
With the SA1100 and PXA RTC drivers be mutually exclusive and no
longer sharing hardware, PXA27x/PXA3xx platforms must use the PXA RTC
driver as the SA1100 platform device is no longer registered.
This change should be almost transparent to userspace. Former users of
pxa-rtc should be aware that 2 RTCs will be available on their kernels,
rtc0 being sa1100-rtc and rtc1 being pxa-rtc. Any userspace relying on
the fact that rtc0 was pxa-rtc should be fixed.
As a consequence:
- the first reboot after the switch will have the wrong time,
- on dual boot platform where the other OS programs some logic into the
sa1100 rtc IP, a lack of fix in userspace, ie. a kernel changing
sa1100-rtc thinking it is pxa-rtc could have dire consequence, such
as wiping the other OS data partition.
(Thanks to Robert Jarmik for help on the above commit text.)
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
With recent MUSB changes we can now build in support for multiple
DMA implementations. So let's enable DMA by default to make life
easier for distro use.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM SoC defconfig updates from Olof Johansson:
"We mostly keep defconfigs updates on a separate branch due to their
tendency to conflict between platforms and this encourages more
careful separation of code changes and config changes.
Most updates here are minor tweaks, enabling new drivers for various
platforms, and so on. Renesas also removed one defconfig
(marzen_defconfig)"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: add TC2 PM support to multi_v7_defconfig
ARM: tegra: Update multi_v7_defconfig
ARM: tegra: Update default configuration
ARM: at91/defconfig: at91_dt: remove ARM_AT91_ETHER
ARM: at91/defconfig: at91_dt: enable DRM hlcdc support
ARM: at91: at91_dt_defconfig: enable ISI and ov2640 support
ARM: multi_v7_defconfig: Enable Allwinner P2WI, PWM, DMA_SUN6I, cryptodev
ARM: sunxi_defconfig: Enable DMA_SUN6I, P2WI, PWM, cryptodev, EXTCON, FHANDLE
ARM: shmobile: Enable fixed voltage regulator in shmobile_defconfig
ARM: multi_v7_defconfig: Select MX6UL and MX7D
ARM: prima2_defconfig: enable build for hwspinlock
ARM: prima2_defconfig: enable build for RTC
ARM: prima2_defconfig: enable build for misc input
ARM: prima2_defconfig: enable build for SiRFSoC SDHC host
ARM: prima2_defconfig: fix the outdated defconfig
ARM: imx_v6_v7_defconfig: Select CONFIG_IKCONFIG_PROC
ARM: defconfig: orion5x: add DT support
ARM: qcom_defconfig: Enable options for KS8851 ethernet
ARM: multi_v7_defconfig: Enable support for PWM Regulators
ARM: multi_v7_defconfig: Enable ST's PWM driver
...
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
Pull ARM SoC cleanups from Olof Johansson:
"A large cleanup branch this release, with a healthy 10k negative line
delta.
Most of this is removal of legacy (non-DT) support of shmobile
platforms. There is also removal of two non-DT platforms on OMAP, and
the plat-samsung directory is cleaned out by moving most of the
previously shared-location-but-not-actually-shared files from there to
the appropriate mach directories instead.
There are other sets of changes in here as well:
- Rob Herring removed use of set_irq_flags under all platforms and
moved to genirq alternatives
- a series of timer API conversions to set-state interface
- ep93xx, nomadik and ux500 cleanups from Linus Walleij
- __init annotation fixes from Nicolas Pitre
+ a bunch of other changes that all add up to a nice set of cleanups"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (108 commits)
ARM/fb: ep93xx: switch framebuffer to use modedb only
ARM: gemini: Setup timer3 as free running timer
ARM: gemini: Use timer1 for clockevent
ARM: gemini: Add missing register definitions for gemini timer
ARM: ep93xx/timer: Migrate to new 'set-state' interface
ARM: nomadik: push accelerometer down to boards
ARM: nomadik: move l2x0 setup to device tree
ARM: nomadik: selectively enable UART0 on boards
ARM: nomadik: move hog code to use DT hogs
ARM: shmobile: Fix mismerges
ARM: ux500: simplify secondary CPU boot
ARM: SAMSUNG: remove keypad-core header in plat-samsung
ARM: SAMSUNG: local watchdog-reset header in mach-s3c64xx
ARM: SAMSUNG: local onenand-core header in mach-s3c64xx
ARM: SAMSUNG: local irq-uart header in mach-s3c64xx
ARM: SAMSUNG: local backlight header in mach-s3c64xx
ARM: SAMSUNG: local ata-core header in mach-s3c64xx
ARM: SAMSUNG: local regs-usb-hsotg-phy header in mach-s3c64xx
ARM: SAMSUNG: local spi-core header in mach-s3c24xx
ARM: SAMSUNG: local nand-core header in mach-s3c24xx
...
ARM: tegra: Default configuration updates for v4.3-rc1
Enable the GK20A GPU (via the Nouveau driver) and CPU frequency scaling
on Tegra124.
* tag 'tegra-for-4.3-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Update multi_v7_defconfig
ARM: tegra: Update default configuration
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung defconfig updates for v4.3
- for exynos_defconfig
: enable SND_SOC_ODROIDX2 and SND_SIMPLE_CARD for
Odroid-XU3 to use max98090 audio codec
: enalbe SENSORS_NTC_THERMISTOR for Peach boards
: enable cpufreq-dt driver with ONDEMAND governor
for Exynos SoCs 3250, 4210, 4212, 4412 and 5250
- for multi_v7_defconfig:
: remove SAMSUNG_USB2PHY and SAMSUNG_USB3PHY are not used now
: enable SENSORS_NTC_THERMISTOR and EXYNOS_ADC for Peach boards
: enable REGULATOR_MAX77802 for Peach boards
* tag 'samsung-defconfig-new' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable cpufreq-dt driver
ARM: multi_v7_defconfig: Enable max77802 regulator
ARM: exynos_defconfig: Enable NTC Thermistors support
ARM: multi_v7_defconfig: Enable NTC Thermistors support
ARM: multi_v7_defconfig: Remove old Samsung USB PHY configs
ARM: exynos_defconfig: Enable CONFIG_SND_SOC_ODROIDX2 for Odroid-XU3
Signed-off-by: Olof Johansson <olof@lixom.net>
Without this, the multi_v7_defconfig kernel cannot boot all CPUs
nor do deep cpuidle power saving on a TC2 board.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX defconfig updates for 4.3:
- Enable i.MX6UL SoC build
- Enable powerkey and syscon poweroff support
- Build in multi-channel audio support, including i.MX ASRC and CS42xx8
codec drivers.
- Enable kexec build, HCIUART_H4 and IKCONFIG_PROC support.
* tag 'imx-defconfig-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: Select CONFIG_IKCONFIG_PROC
ARM: imx: imx_v6_v7_defconfig enable imx6ul support
ARM: imx_v6_v7_defconfig: enable powerkey and syscon power off
ARM: imx_v6_v7_defconfig: Select HCIUART_H4
ARM: imx_v6_v7_defconfig: build in audio driver
ARM: imx_v6_v7_defconfig: Enable kexec support
Signed-off-by: Olof Johansson <olof@lixom.net>
drm/panel: Changes for v4.3-rc1
This introduces support for a couple of new panels and also contains
some work to restructure the directories to get more consistency, to
deal better with more panel and bridge drivers getting added.
* tag 'drm/panel/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/bridge: Put Kconfig entries in a separate menu
drm/panel: Add support for LG LG4573 480x800 4.3" panel
drm/panel: Add display timing for Okaya RS800480T-7X0GP
of: Add Okaya Electric America vendor prefix
drm/panel: simple: Add support for NEC NL4827HC19-05B 480x272 panel
drm/panel: simple: Add support for AUO B080UAN01
drm/panel: simple: Correct minimum hsync length of the HannStar HSD070PWW1 panel
drm/panel: simple: Add bus format for HannStar HSD070PWW1 LVDS panel
drm/bridge: Add vendor prefixes
drm/panel: Add Samsung prefix to panel drivers
drm/exynos: Remove PTN3460 dependency
Use vendor prefixes for Kconfig symbols and filenames. This should make
it easier to identify the various bridge drivers and to organize the
directory.
v2: fix object name for dw-hdmi (Fabio Estevam)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add Tegra-specific configuration options to multi_v7_defconfig:
* HDA controller and codec support
* Watchdog support
* Nouveau (for GK20A GPU) support
Signed-off-by: Thierry Reding <treding@nvidia.com>
The likelihood of getting a large number of panel drivers from different
vendors is quite high. Add a prefix to the two existing Samsung panel
drivers to set a guideline for future patch submissions. Using vendor
prefixes consistently should allow a cleaner organization of the tree.
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
CONFIG_ARM_AT91_ETHER doesn't exist anymore, both drivers have been merged
in the macb driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
With the latest patches the cpufreq-dt can be used on multiple
Exynos SoCs: 3250, 4210, 4212, 4412 and 5250.
Enable it along with default ondemand governor to conserve the energy,
reduce temperature while maintaining acceptable performance.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 based Peach Pit and Exynos5800 based Peach Pi Chromebooks
use the Maxim max77802 Power Management IC (PMIC). This PMIC has besides
other devices, a set of regulators that can be controller over I2C.
Commit f3caa529c6 ("ARM: multi_v7_defconfig: Enable max77802 regulator,
rtc and clock drivers") was supposed to enable the config option for the
regulator driver as a module but the final version that landed did not
include this. The commit was modified and the REGULATOR_MAX77802 removed
since it was thought to be useless.
Unfortunately that's not the case for the mentioned reason above so this
patch enables the needed Kconfig option.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[kgene@kernel.org: fixed ordering according to make savedefconfig]
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Allwinner defconfig changes for 4.3
Two patches that enable various Allwinner related drivers drivers both in
sunxi_defconfig and in multi_v7_defconfig
* tag 'sunxi-defconfig-for-4.3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: multi_v7_defconfig: Enable Allwinner P2WI, PWM, DMA_SUN6I, cryptodev
ARM: sunxi_defconfig: Enable DMA_SUN6I, P2WI, PWM, cryptodev, EXTCON, FHANDLE
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu config changes for v4.3 (part #2)
Improve dt support for orion5x
* tag 'mvebu-config-4.3-2' of git://git.infradead.org/linux-mvebu:
ARM: defconfig: orion5x: add DT support
Signed-off-by: Olof Johansson <olof@lixom.net>
Qualcomm ARM Based defconfig Updates for v4.3
* Enable KS8851 for QCOM SoCs in qcom defconfig
* tag 'qcom-defconfig-for-4.3' of git://codeaurora.org/quic/kernel/agross-msm:
ARM: qcom_defconfig: Enable options for KS8851 ethernet
Signed-off-by: Olof Johansson <olof@lixom.net>
Add Atmel-isi and ov2640 driver in defconfig
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[nicolas.ferre@atmel.com: make SOC_CAMERA_OV2640 selected as a module]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Second Round of Renesas ARM Based SoC Defconfig Updates for v4.3
* Enable fixed voltage regulator in shmobile_defconfig
* tag 'renesas-defconfig2-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Enable fixed voltage regulator in shmobile_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable drivers for Allwinner P2WI, PWM, cryptodev (Security System) and
sun6i DMA engine. Also enable EXTCON as PHY_SUN4I_USB depends on it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable sun6i DMA engine, sun6i P2WI, PWM, and crypto engine (Security
System) drivers by default. EXTCON is needed by the updated sun4i USB
PHY driver.
While at it, enable FHANDLE, which is needed by systemd and newer
versions of udev. Also enable CGROUPS for systemd.
And get rid of POWER_RESET, as the sun6i power reset driver has been
removed in favor of proper sun6i watchdog support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Exynos5420 Peach Pit and Exynos5800 Peach Pi Chromebooks have
IIO based ADC thermistors. Enable built-in support for its driver.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 Peach Pit and Exynos5800 Peach Pi Chromebooks have
IIO based ADC thermistors. Enable module support for its driver
and also for the needed Exynos ADC driver.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The old drivers/usb/phy/phy-samsung-usb{2,3} are now deleted since
were replaced by newer drivers that use the Generic PHY framework
but their Kconfig options were left over in multi_v7_defconfig.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Enable CONFIG_SND_SOC_ODROIDX2 and CONFIG_SND_SIMPLE_CARD to enable
sound on Odroid-XU3 board using the max98090 audio codec.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This is selected by MACH_MARZEN which is enabled in shmobile_defconfig,
however, MACH_MARZEN is going away along with the board code it enables.
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Merge "CSR prima2_defconfig fixes for 4.2" from Barry Song:
enable SiRFSoC device drivers in CSR prima2_defconfig
make savedefconfig at first, then enable
1. sdhci driver
2. onkey
3. rtc
4. hwspinlock
for prima2_defconfig
* tag 'prima2-defconfig-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: prima2_defconfig: enable build for hwspinlock
ARM: prima2_defconfig: enable build for RTC
ARM: prima2_defconfig: enable build for misc input
ARM: prima2_defconfig: enable build for SiRFSoC SDHC host
ARM: prima2_defconfig: fix the outdated defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
this patch is againest v4.2-rc1, by doing:
$ make ARCH=arm prima2_defconfig
$ make ARCH=arm savedefconfig
$ cp defconfig arch/arm/configs/prima2_defconfig
Signed-off-by: Barry Song <Baohua.Song@csr.com>
It is useful to know how the kernel was configured via:
zcat /proc/config.gz ,so select the CONFIG_IKCONFIG_PROC option.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
STi defconfig for v4.3, round 1
Highlights:
-----------
- Enable support ST's PWM driver in multi_v7
- Enable support PWM regulator in multi_v7
* tag 'sti-defconfig-for-v4.3-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
ARM: multi_v7_defconfig: Enable support for PWM Regulators
ARM: multi_v7_defconfig: Enable ST's PWM driver
Signed-off-by: Olof Johansson <olof@lixom.net>
