Broadcast allowed only one global APIC mode, but mixed modes are
theoretically possible. x2APIC IPI doesn't mean 0xff as broadcast,
the rest does.
x2APIC broadcasts are accepted by xAPIC. If we take SDM to be logical,
even addreses beginning with 0xff should be accepted, but real hardware
disagrees. This patch aims for simple code by considering most of real
behavior as undefined.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <1423766494-26150-3-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
cpuid_maxphyaddr(), which performs lot of memory accesses is called
extensively across KVM, especially in nVMX code.
This patch adds a cached value of maxphyaddr to vcpu.arch to reduce the
pressure onto CPU cache and simplify the code of cpuid_maxphyaddr()
callers. The cached value is initialized in kvm_arch_vcpu_init() and
reloaded every time CPUID is updated by usermode. It is obvious that
these reloads occur infrequently.
Signed-off-by: Eugene Korenevsky <ekorenevsky@gmail.com>
Message-Id: <20150329205612.GA1223@gnote>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Interrupt entry points are handled with the following code,
each 32-byte code block contains seven entry points:
...
[push][jump 22] // 4 bytes
[push][jump 18] // 4 bytes
[push][jump 14] // 4 bytes
[push][jump 10] // 4 bytes
[push][jump 6] // 4 bytes
[push][jump 2] // 4 bytes
[push][jump common_interrupt][padding] // 8 bytes
[push][jump]
[push][jump]
[push][jump]
[push][jump]
[push][jump]
[push][jump]
[push][jump common_interrupt][padding]
[padding_2]
common_interrupt:
And there is a table which holds pointers to every entry point,
IOW: to every push.
In cold cache, two jumps are still costlier than one, even
though we get the benefit of them residing in the same
cacheline.
This change replaces short jumps with near ones to
'common_interrupt', and pads every push+jump pair to 8 bytes. This
way, each interrupt takes only one jump.
This change replaces ".p2align CONFIG_X86_L1_CACHE_SHIFT" before
dispatch table with ".align 8" - we do not need anything
stronger than that.
The table of entry addresses (the interrupt[] array) is no
longer necessary, the address of entries can be easily
calculated as (irq_entries_start + i*8).
text data bss dec hex filename
12546 0 0 12546 3102 entry_64.o.before
11626 0 0 11626 2d6a entry_64.o
The size decrease is because 1656 bytes of .init.rodata are
gone. That's initdata, though. The resident size does go up a
bit.
Run-tested (32 and 64 bits).
Acked-and-Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428090553-7283-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On failure, sys_execve() does not clobber EXTRA_REGS, so we can
just return to userpsace without saving/restoring them.
On success, ELF_PLAT_INIT() in sys_execve() clears all these
registers.
On other executable formats:
- binfmt_flat.c has similar FLAT_PLAT_INIT, but x86 (and everyone
else except sh) doesn't define it.
- binfmt_elf_fdpic.c has ELF_FDPIC_PLAT_INIT, but x86 (and most
others) doesn't define it.
- There are no such hooks in binfmt_aout.c et al. We inherit
EXTRA_REGS from the prior executable.
This inconsistency was not intended.
This change removes SAVE/RESTORE_EXTRA_REGS in stub_execve,
removes register clearing in ELF_PLAT_INIT(),
and instead simply clears them on success in stub_execve.
Run-tested.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428173719-7637-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Quentin caught a corner case with the generation of instruction
padding in the ALTERNATIVE_2 macro: if len(orig_insn) <
len(alt1) < len(alt2), then not enough padding gets added and
that is not good(tm) as we could overwrite the beginning of the
next instruction.
Luckily, at the time of this writing, we don't have
ALTERNATIVE_2() invocations which have that problem and even if
we did, a simple fix would be to prepend the instructions with
enough prefixes so that that corner case doesn't happen.
However, best it would be if we fixed it properly. See below for
a simple, abstracted example of what we're doing.
So what we ended up doing is, we compute the
max(len(alt1), len(alt2)) - len(orig_insn)
and feed that value to the .skip gas directive. The max() cannot
have conditionals due to gas limitations, thus the fancy integer
math.
With this patch, all ALTERNATIVE_2 sites get padded correctly;
generating obscure test cases pass too:
#define alt_max_short(a, b) ((a) ^ (((a) ^ (b)) & -(-((a) < (b)))))
#define gen_skip(orig, alt1, alt2, marker) \
.skip -((alt_max_short(alt1, alt2) - (orig)) > 0) * \
(alt_max_short(alt1, alt2) - (orig)),marker
.pushsection .text, "ax"
.globl main
main:
gen_skip(1, 2, 4, 0x09)
gen_skip(4, 1, 2, 0x10)
...
.popsection
Thanks to Quentin for catching it and double-checking the fix!
Reported-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150404133443.GE21152@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
e2b32e6785 ("x86, kaslr: randomize module base load address")
made module base address randomization unconditional and didn't regard
disabled KKASLR due to CONFIG_HIBERNATION and command line option
"nokaslr". For more info see (now reverted) commit:
f47233c2d3 ("x86/mm/ASLR: Propagate base load address calculation")
In order to propagate KASLR status to kernel proper, we need a single bit
in boot_params.hdr.loadflags and we've chosen bit 1 thus leaving the
top-down allocated bits for bits supposed to be used by the bootloader.
Originally-From: Jiri Kosina <jkosina@suse.cz>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add support for the new CLWB (cache line write back)
instruction. This instruction was announced in the document
"Intel Architecture Instruction Set Extensions Programming
Reference" with reference number 319433-022.
https://software.intel.com/sites/default/files/managed/0d/53/319433-022.pdf
The CLWB instruction is used to write back the contents of
dirtied cache lines to memory without evicting the cache lines
from the processor's cache hierarchy. This should be used in
favor of clflushopt or clflush in cases where you require the
cache line to be written to memory but plan to access the data
again in the near future.
One of the main use cases for this is with persistent memory
where CLWB can be used with PCOMMIT to ensure that data has been
accepted to memory and is durable on the DIMM.
This function shows how to properly use CLWB/CLFLUSHOPT/CLFLUSH
and PCOMMIT with appropriate fencing:
void flush_and_commit_buffer(void *vaddr, unsigned int size)
{
void *vend = vaddr + size - 1;
for (; vaddr < vend; vaddr += boot_cpu_data.x86_clflush_size)
clwb(vaddr);
/* Flush any possible final partial cacheline */
clwb(vend);
/*
* Use SFENCE to order CLWB/CLFLUSHOPT/CLFLUSH cache flushes.
* (MFENCE via mb() also works)
*/
wmb();
/* PCOMMIT and the required SFENCE for ordering */
pcommit_sfence();
}
After this function completes the data pointed to by vaddr is
has been accepted to memory and will be durable if the vaddr
points to persistent memory.
Regarding the details of how the alternatives assembly is set
up, we need one additional byte at the beginning of the CLFLUSH
so that we can flip it into a CLFLUSHOPT by changing that byte
into a 0x66 prefix. Two options are to either insert a 1 byte
ASM_NOP1, or to add a 1 byte NOP_DS_PREFIX. Both have no
functional effect with the plain CLFLUSH, but I've been told
that executing a CLFLUSH + prefix should be faster than
executing a CLFLUSH + NOP.
We had to hard code the assembly for CLWB because, lacking the
ability to assemble the CLWB instruction itself, the next
closest thing is to have an xsaveopt instruction with a 0x66
prefix. Unfortunately XSAVEOPT itself is also relatively new,
and isn't included by all the GCC versions that the kernel needs
to support.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1422377631-8986-3-git-send-email-ross.zwisler@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull EFI updates from Matt Fleming:
- Fixes and cleanups for SMBIOS 3.0 DMI code. (Ivan Khoronzhuk)
- A new efi=debug command line option that enables debug output in the
EFI boot stub and results in less verbose EFI memory map output by
default. (Borislav Petkov)
- Disable interrupts around EFI calls and use a more standard page
table saving and restoring idiom when making EFI calls. (Ingo Molnar)
- Reduce the number of memory allocations performed when allocating the
FDT in EFI boot stub by retrieving size from the FDT header in the
EFI config table. (Ard Biesheuvel)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently x86-64 efi_call_phys_prolog() saves into a global variable (save_pgd),
and efi_call_phys_epilog() restores the kernel pagetables from that global
variable.
Change this to a cleaner save/restore pattern where the saving function returns
the saved object and the restore function restores that.
Apply the same concept to the 32-bit code as well.
Plus this approach, as an added bonus, allows us to express the
!efi_enabled(EFI_OLD_MEMMAP) situation in a clean fashion as well,
via a 'NULL' return value.
Cc: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
user_mode_ignore_vm86() can be used instead of user_mode(), in
places where we have already done a v8086_mode() security
check of ptregs.
But doing this check in the wrong place would be a bug that
could result in security problems, and also the naming still
isn't very clear.
Furthermore, it only affects 32-bit kernels, while most
development happens on 64-bit kernels.
If we replace them with user_mode() checks then the cost is only
a very minor increase in various slowpaths:
text data bss dec hex filename
10573391 703562 1753042 13029995 c6d26b vmlinux.o.before
10573423 703562 1753042 13030027 c6d28b vmlinux.o.after
So lets get rid of this distinction once and for all.
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150329090233.GA1963@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ASLR implementation needs to special-case AMD F15h processors by
clearing out bits [14:12] of the virtual address in order to avoid I$
cross invalidations and thus performance penalty for certain workloads.
For details, see:
dfb09f9b7a ("x86, amd: Avoid cache aliasing penalties on AMD family 15h")
This special case reduces the mmapped file's entropy by 3 bits.
The following output is the run on an AMD Opteron 62xx class CPU
processor under x86_64 Linux 4.0.0:
$ for i in `seq 1 10`; do cat /proc/self/maps | grep "r-xp.*libc" ; done
b7588000-b7736000 r-xp 00000000 00:01 4924 /lib/i386-linux-gnu/libc.so.6
b7570000-b771e000 r-xp 00000000 00:01 4924 /lib/i386-linux-gnu/libc.so.6
b75d0000-b777e000 r-xp 00000000 00:01 4924 /lib/i386-linux-gnu/libc.so.6
b75b0000-b775e000 r-xp 00000000 00:01 4924 /lib/i386-linux-gnu/libc.so.6
b7578000-b7726000 r-xp 00000000 00:01 4924 /lib/i386-linux-gnu/libc.so.6
...
Bits [12:14] are always 0, i.e. the address always ends in 0x8000 or
0x0000.
32-bit systems, as in the example above, are especially sensitive
to this issue because 32-bit randomness for VA space is 8 bits (see
mmap_rnd()). With the Bulldozer special case, this diminishes to only 32
different slots of mmap virtual addresses.
This patch randomizes per boot the three affected bits rather than
setting them to zero. Since all the shared pages have the same value
at bits [12..14], there is no cache aliasing problems. This value gets
generated during system boot and it is thus not known to a potential
remote attacker. Therefore, the impact from the Bulldozer workaround
gets diminished and ASLR randomness increased.
More details at:
http://hmarco.org/bugs/AMD-Bulldozer-linux-ASLR-weakness-reducing-mmaped-files-by-eight.html
Original white paper by AMD dealing with the issue:
http://developer.amd.com/wordpress/media/2012/10/SharedL1InstructionCacheonAMD15hCPU.pdf
Mentored-by: Ismael Ripoll <iripoll@disca.upv.es>
Signed-off-by: Hector Marco-Gisbert <hecmargi@upv.es>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jan-Simon <dl9pf@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-fsdevel@vger.kernel.org
Link: http://lkml.kernel.org/r/1427456301-3764-1-git-send-email-hecmargi@upv.es
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull RCU updates from Paul E. McKenney:
- Documentation updates.
- Changes permitting use of call_rcu() and friends very early in
boot, for example, before rcu_init() is invoked.
- Miscellaneous fixes.
- Add in-kernel API to enable and disable expediting of normal RCU
grace periods.
- Improve RCU's handling of (hotplug-) outgoing CPUs.
Note: ARM support is lagging a bit here, and these improved
diagnostics might generate (harmless) splats.
- NO_HZ_FULL_SYSIDLE fixes.
- Tiny RCU updates to make it more tiny.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the guest CPU is supposed to support rdtscp and the host has rdtscp
enabled in the secondary execution controls, we can also expose this
feature to L1. Just extend nested_vmx_exit_handled to properly route
EXIT_REASON_RDTSCP.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
- extend/clarify explanations where necessary
- move comments from macro values to before the macro, to
make them more consistent, and to reduce preprocessor overhead
- sort GDT index and selector values likewise by number
- use consistent, modern kernel coding style across the file
- capitalize consistently
- use consistent vertical spacing
- remove the unused get_limit() method (noticed by Andy Lutomirski)
No change in code (verified with objdump -d):
64-bit defconfig+kvmconfig:
815a129bc1f80de6445c1d8ca5b97cad vmlinux.o.before.asm
815a129bc1f80de6445c1d8ca5b97cad vmlinux.o.after.asm
32-bit defconfig+kvmconfig:
e659ef045159ddf41a0771b33a34aae5 vmlinux.o.before.asm
e659ef045159ddf41a0771b33a34aae5 vmlinux.o.after.asm
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Drewry <wad@chromium.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This file just defines a number of constants, and a few macros
and inline functions. It is particularly badly written.
For example, it is not trivial to see how descriptors are
numbered (you'd expect that should be easy, right?).
This change deobfuscates it via the following changes:
Group all GDT_ENTRY_foo together (move intervening stuff away).
Number them explicitly: use a number, not PREV_DEFINE+1, +2, +3:
I want to immediately see that GDT_ENTRY_PNPBIOS_CS32 is 18.
Seeing (GDT_ENTRY_KERNEL_BASE+6) instead is not useful.
The above change allows to remove GDT_ENTRY_KERNEL_BASE
and GDT_ENTRY_PNPBIOS_BASE, which weren't used anywhere else.
After a group of GDT_ENTRY_foo, define all selector values.
Remove or improve some comments. In particular:
Comment deleted as stating the obvious:
/*
* The GDT has 32 entries
*/
#define GDT_ENTRIES 32
"The segment offset needs to contain a RPL. Grr. -AK"
changed to
"Selectors need to also have a correct RPL (+3 thingy)"
"GDT layout to get 64bit syscall right (sysret hardcodes gdt
offsets)" expanded into a description *how exactly* sysret
hardcodes them.
Patch was tested to compile and not change vmlinux.o
on 32-bit and 64-bit builds (verified with objdump).
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Drewry <wad@chromium.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
PER_CPU_VAR(kernel_stack) was set up in a way where it points
five stack slots below the top of stack.
Presumably, it was done to avoid one "sub $5*8,%rsp"
in syscall/sysenter code paths, where iret frame needs to be
created by hand.
Ironically, none of them benefits from this optimization,
since all of them need to allocate additional data on stack
(struct pt_regs), so they still have to perform subtraction.
This patch eliminates KERNEL_STACK_OFFSET.
PER_CPU_VAR(kernel_stack) now points directly to top of stack.
pt_regs allocations are adjusted to allocate iret frame as well.
Hopefully we can merge it later with 32-bit specific
PER_CPU_VAR(cpu_current_top_of_stack) variable...
Net result in generated code is that constants in several insns
are changed.
This change is necessary for changing struct pt_regs creation
in SYSCALL64 code path from MOV to PUSH instructions.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1426785469-15125-2-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This changes the THREAD_INFO() definition and all its callsites
so that they do not count stack position from
(top of stack - KERNEL_STACK_OFFSET), but from top of stack.
Semi-mysterious expressions THREAD_INFO(%rsp,RIP) - "why RIP??"
are now replaced by more logical THREAD_INFO(%rsp,SIZEOF_PTREGS)
- "calculate thread_info's address using information that
rsp is SIZEOF_PTREGS bytes below top of stack".
While at it, replace "(off)-THREAD_SIZE(reg)" with equivalent
"((off)-THREAD_SIZE)(reg)". The form without parentheses
falsely looks like we invoke THREAD_SIZE() macro.
Improve comment atop THREAD_INFO macro definition.
This patch does not change generated code (verified by objdump).
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1426785469-15125-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a severities function that caters to AMD processors. This allows us
to do some vendor-specific work within the function if necessary.
Also, introduce a vendor flag bitfield for vendor-specific settings. The
severities code uses this to define error scope based on the prescence
of the flags field.
This is based off of work by Boris Petkov.
Testing details:
Fam10h, Model 9h (Greyhound)
Fam15h: Models 0h-0fh (Orochi), 30h-3fh (Kaveri) and 60h-6fh (Carrizo),
Fam16h Model 00h-0fh (Kabini)
Boris:
Intel SNB
AMD K8 (JH-E0)
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Chen Yucong <slaoub@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: linux-edac@vger.kernel.org
Link: http://lkml.kernel.org/r/1427125373-2918-2-git-send-email-Aravind.Gopalakrishnan@amd.com
[ Fixup build, clean up comments. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The last patch reduced our interrupt-suppression region to one address,
so simplify the code somewhat.
Also, remove the obsolete undefined instruction ranges and the comment
which refers to lguest_guest.S instead of head_32.S.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The following point:
2. per-CPU pvclock time info is updated if the
underlying CPU changes.
Is not true anymore since "KVM: x86: update pvclock area conditionally,
on cpu migration".
Add task migration notification back.
Problem noticed by Andy Lutomirski.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
CC: stable@kernel.org # 3.11+
Call it what it does and in accordance with the context where it is
used: we reset the FPU state either because we were unable to restore it
from the one saved in the task or because we simply want to reset it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Extract the "use_eager_fpu()" code from drop_init_fpu() into a new,
simple helper restore_init_xstate(). The next patch adds another user.
- It is not clear why we do not check use_fxsr() like fpu_restore_checking()
does. eager_fpu_init_bp() calls setup_init_fpu_buf() too, and we have the
"eagerfpu=on" kernel option.
- Ignoring the fact that init_xstate_buf is "struct xsave_struct *", not
"union thread_xstate *", it is not clear why we can not simply use
fpu_restore_checking() and avoid the code duplication.
- It is not clear why we can't call setup_init_fpu_buf() unconditionally
to always create init_xstate_buf(). Then do_device_not_available() path
(at least) could use restore_init_xstate() too. It doesn't need to init
fpu->state, its content doesn't matter until unlazy_fpu()/__switch_to()/etc
which overwrites this memory anyway.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pekka Riikonen <priikone@iki.fi>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Link: http://lkml.kernel.org/r/20150311173429.GD5032@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
