The Mele A1000G-quad has an usb to sata bridge connected to its otg
controller, this commit enables support for this. Since the otg is
hardwired to the sata bridge it gets enabled in host only mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the Cubieboard. Note that the
5V of the otg is directly connected to the general 5V, so we only use
the id pin.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A23/A33 has one pair of EHCI/OHCI USB controllers. There are 2 USB PHYs,
one for the USB OTG controller, one for the EHCI/OHCI pair. The latter
may also support HSIC, though none of the available boards utilize this,
so this is not supported yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Note these are added to the sun8i-a33.dtsi file rather then to the shared
sun8i-a23-a33.dtsi file as both the phy and the otg controller on the a33
are slightly different.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Note these are added to the sun8i-a23.dtsi file rather then to the shared
sun8i-a23-a33.dtsi file as both the phy and the otg controller on the a33
are slightly different.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Bitrot has set in for this driver and the sh-vou clock was never enabled,
since the clock name in clock-sh7724.c was wrong. It should be sh-vou, not
sh-vou.0.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Thanks-to: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The conversion of opal events to a proper irqchip means that handlers
are called until the relevant opal event has been cleared by
processing it. Events that queue work should therefore use a threaded
handler to mask the event until processing is complete.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An earlier commit referenced 'hose_list' in sysdev/ppc4xx_hsta_msi.c.
hose_list is defined in ppc-pci.h, which was not included in that
file. Include it, fixing the build for the akebono defconfig used
by the kbuild test robot.
Fixes: f2c800aace ("powerpc/ppc4xx_hsta_msi: Move MSI-related ops to pci_controller_ops")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If we take an alignment exception which we cannot fix, the oops
currently prints:
Unable to handle kernel paging request for unknown fault
Lets print something more useful:
Unable to handle kernel paging request for unaligned access at address 0xc0000000f77bba8f
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This means the 'M' flag will work properly when the kernel prints a backtrace.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The following was seen in branch[0] build.
arch/arm/mach-rockchip/platsmp.c:154:23: error:
'rockchip_secondary_startup' undeclared (first use in this function)
branch[0]:
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git
v4.3-armsoc/soc
The broken build is caused by the commit fe4407c0dc
("ARM: rockchip: fix the CPU soft reset").
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
The breakage was a result of it being wrongly merged in my branch with
the cache invalidation rework from Russell 02b4e2756e
("ARM: v7 setup function should invalidate L1 cache").
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
If it takes longer than 12us to read the PIT counter lsb/msb,
then the error margin will never fall below 500ppm within 50ms,
and Fast TSC calibration will always fail.
This patch detects when that will happen and fails fast. Note
the failure message is not printed in that case because:
1. it will always happen on that class of hardware
2. the absence of the message is more informative than its
presence
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/556EB717.9070607@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With this nsim standlone / OSCI have working irq affinity - AXS103 still
needs some work as IDU is not visible in intc hierarchy yet !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
alloc_pages_exact() get gfp flags and handle zero'ing already
And while it, fix the case where ioremap fails: return rightaway.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC kernels have historically been built with -O3, despite top level
Makefile defaulting to -O2. This was facilitated by implicitly ordering
of arch makefile include AFTER top level assigned -O2.
An upstream fix to top level a1c48bb160 ("Makefile: Fix unrecognized
cross-compiler command line options") changed the ordering, making ARC
-O3 defunct.
Fix that by NOT relying on any ordering whatsoever and use the proper
arch override facility now present in kbuild (ARCH_*FLAGS)
Depends-on: ("kbuild: Allow arch Makefiles to override {cpp,ld,c}flags")
Suggested-by: Michal Marek <mmarek@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
SLC maintenance ops need to be serialized by software as there is no
inherent buffering / quequing of aux commands. It can silently ignore a
new aux operation if previous one is still ongoing (SLC_CTRL_BUSY)
So gaurd the SLC op using a spin lock
The spin lock doesn't seem to be contended even in heavy workloads such
as iperf. On FPGA @ 75 MHz.
[1] Before this change:
============================================================
# iperf -c 10.42.0.1
------------------------------------------------------------
Client connecting to 10.42.0.1, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 10.42.0.110 port 38935 connected with 10.42.0.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 48.4 MBytes 40.6 Mbits/sec
============================================================
[2] After this change:
============================================================
# iperf -c 10.42.0.1
------------------------------------------------------------
Client connecting to 10.42.0.1, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 10.42.0.243 port 60248 connected with 10.42.0.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 47.5 MBytes 39.8 Mbits/sec
# iperf -c 10.42.0.1
------------------------------------------------------------
Client connecting to 10.42.0.1, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 10.42.0.243 port 60249 connected with 10.42.0.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 54.9 MBytes 46.0 Mbits/sec
============================================================
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-linux-dev@synopsys.com
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
opal-prd driver will mmap() firmware code/data area as private
mapping to prd user space daemon. Write to this page will
trigger COW faults. The new COW pages are normal kernel RAM
pages accounted by the kernel and are not special.
vma->vm_page_prot value will be used at page fault time
for the new COW pages, while pgprot_t value passed in
remap_pfn_range() is used for the initial page table entry.
Hence:
* Do not add _PAGE_SPECIAL in vma, but only for remap_pfn_range()
* Also remap_pfn_range() will add the _PAGE_SPECIAL flag using
pte_mkspecial() call, hence no need to specify in the driver
This fix resolves the page accounting warning shown below:
BUG: Bad rss-counter state mm:c0000007d34ac600 idx:1 val:19
The above warning is triggered since _PAGE_SPECIAL was incorrectly
being set for the normal kernel COW pages.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simplify the power request code by passing an "on" flag, and picking the
right status bit and register offset in the innermost function, based on
this flag.
This allows to remove the rcar_sysc_pwr_{off,on}() helper functions, and
the function pointer through which they were called.
Make sr_bit and reg_offs unsigned while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
rcar_sysc_update() loops (with interrupts disabled and while holding a
spinlock) until submitting a power shutoff or resume request fails, or
until the submitted request was accepted.
If none of these conditions becomes true, this forms an infinite loop.
Put a limit on the maximum number of loop iterations, and add a small
delay to each iteration, to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Shrink the individual fields in struct rcar_sysc_ch, as unsigned long or
int is overkill:
- chan_offs contains a register offset relative to a base value
(< 512),
- chan_bit and isr_bit contain bit indices (0-31).
This reduces the size of each instance from 3 (4 on 64-bit) 32-bit words
to 1 32-bit word.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add more SYSC register documentation.
Use definitions instead of hardcoded numbers.
Comment important operations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register (on r8a7791),
which reports 0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register (on r8a7791),
which reports 0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the R-Car Gen2 GIC is assumed to be a GIC-400.
This has been confirmed by reading the GICD_IIDR register (on r8a7791),
which reports 0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a15-gic" compatible value for the GIC by
"arm,gic-400", as the documentation states it's a GIC-400.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0200043b (GIC-400 = 0x02, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Configure pinctrl and a GPIO-controller board mux for LCD use.
This allows the armadillo800eva board staging code to enable lcdc0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Minimal r8a7793 device tree including one CPU core, interrupt controllers,
timers, two serial ports, and the Ethernet controller, plus the required
clock descriptions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
