This patch add support for Two Dimensional Animation and Compositing
Engine (2D-ACE) on the Freescale SoCs.
2D-ACE is a Freescale display controller. 2D-ACE describes
the functionality of the module extremely well its name is a value
that cannot be used as a token in programming languages.
Instead the valid token "DCU" is used to tag the register names and
function names.
The Display Controller Unit (DCU) module is a system master that
fetches graphics stored in internal or external memory and displays
them on a TFT LCD panel. A wide range of panel sizes is supported
and the timing of the interface signals is highly configurable.
Graphics are read directly from memory and then blended in real-time,
which allows for dynamic content creation with minimal CPU
intervention.
The features:
(1) Full RGB888 output to TFT LCD panel.
(2) Blending of each pixel using up to 4 source layers
dependent
on size of panel.
(3) Each graphic layer can be placed with one pixel resolution
in either axis.
(4) Each graphic layer support RGB565 and RGB888 direct colors
without alpha channel and BGRA8888 BGRA4444 ARGB1555 direct
colors
with an alpha channel and YUV422 format.
(5) Each graphic layer support alpha blending with 8-bit
resolution.
This is a simplified version, only one primary plane, one
framebuffer, one crtc, one connector and one encoder for TFT
LCD panel.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The following PR add support for 3 more atmel SoCs and for some missing
features (new input formats and PRIME support).
* 'drm-atmel-hlcdc-devel' of https://github.com/bbrezillon/linux-at91:
drm: atmel-hlcdc: add support for sama5d4 SoCs
drm: atmel-hlcdc: add support for at91sam9n12 SoC
drm: atmel-hlcdc: add support for at91sam9x5 SoCs
drm: atmel-hlcdc: add RGB565 and RGB444 output support
drm: atmel-hlcdc: add the missing DRM_ATOMIC flag
drm: atmel-hlcdc: add PRIME support
This patch removes TP3 support on CHV since there is no support
for HBR2 on this platform.
v2: rename the function to indicate it checks source rates (Jani)
v3: update comment to indicate TP3 dependency on HBR2 supported
hardware (Jani)
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[Jani: fixed a couple of checkpatch warnings.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts
commit 047fe6e6db
Author: David Weinehall <david.weinehall@linux.intel.com>
Date: Tue Aug 4 16:55:52 2015 +0300
drm/i915: Allow parsing of variable size child device entries from VBT
That commit is not valid for v4.2, however it will be valid for v4.3. It
was simply queued too early.
The referenced regressing commit is just fine until the size of struct
common_child_dev_config changes, and that won't happen until
v4.3. Indeed, the expected size checks here rely on the increased size
of the struct, breaking new platforms.
Fixes: 047fe6e6db ("drm/i915: Allow parsing of variable size child device entries from VBT")
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
I2CM_ADDRESS became a MESS, fix it, also change guarding define
to __DW_HDMI_H__ , since the driver is not IMX specific.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dw_hdmi enable/disable handling is particularly weak in several
regards:
* The hotplug interrupt could call hdmi_poweron() or hdmi_poweroff()
while DRM is setting a mode, which could race with a mode being set.
* Hotplug will always re-enable the phy whenever it detects an active
hotplug signal, even if DRM has disabled the output.
Resolve all of these by introducing a mutex to prevent races, and a
state-tracking bool so we know whether DRM wishes the output to be
enabled. We choose to use our own mutex rather than ->struct_mutex
so that we can still process interrupts in a timely fashion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi_phy_enable_power() is not about enabling and disabling power.
It is about allowing or preventing power-down mode being entered - the
register is documented as "Power-down enable (active low 0b)."
This can be seen as the bit has no effect when the HDMI phy is
operational on iMX6 hardware.
Rename the function to dw_hdmi_phy_enable_powerdown() to reflect the
documentation, make it take a bool for the 'enable' argument, and invert
the value to be written.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On a mode set, DRM makes the following sequence of calls:
* for_each_encoder
* bridge mode_fixup
* encoder mode_fixup
* crtc mode_fixup
* for_each_encoder
* bridge disable
* encoder prepare
* bridge post_disable
* disable unused encoders
* crtc prepare
* crtc mode_set
* for_each_encoder
* encoder mode_set
* bridge mode_set
* crtc commit
* for_each_encoder
* bridge pre_enable
* encoder commit
* bridge enable
dw_hdmi enables the HDMI output in both the bridge mode_set() and also
the bridge enable() step. This is duplicated work - we can avoid the
setup in mode_set() and just do it in the enable() stage. This
simplifies the code a little.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only enable audio support if the sink supports audio in some form, as
defined via its EDID. We discover this capability using the generic
drm_detect_monitor_audio() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The FSL kernel detects the HDMI vendor id, and uses this to set
hdmi->edid_cfg.hdmi_cap, which is then used to set mdvi appropriately,
rather than detecting whether we are outputting a CEA mode. Update
the dw_hdmi code to use this logic, but lets eliminate the mdvi
variable, prefering the more verbose "hdmi->sink_is_hdmi" instead.
Use the generic drm_detect_hdmi_monitor() to detect a HDMI sink.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As mentioned in the previous commit, the dw-hdmi driver does not support
pixel doubled modes at present; it does not configure the PLL correctly
for these modes. Therefore, filter out the double-clocked modes as we
presently are unable to support them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi sets a pixel repetition factor of 1 for VICs 10-15, 25-30 and
35-38. However, DRM uses their native resolutions in its timing
information. For example, VIC 14 can be 1440x480 with no repetition,
or 720x480 with one pixel repetition. As DRM uses 1440 pixels per line
for this video mode, we need no pixel repetition.
In any case, pixel repetition appears broken in dw_hdmi.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the struct hdmi_vmode mhsyncpolarity/mvsyncpolarity/minterlaced
members, which are only used within a single function. We can directly
reference the appropriate mode->flags instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a YCBCR format is selected, we can merely copy the colorimetry
information directly as we use the same definitions for both the
unpacked AVI info frame and the hdmi_data_info structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up hdmi_set_clk_regenerator() by allowing it to take the audio
sample rate and ratio directly, rather than hiding it inside the
function. Raise the unsupported pixel clock/sample rate message from
debug to error level as this results in audio not working correctly.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy configuration is dependent on the SoC, and we look up values for
some of the registers in SoC specific data. However, we had partially
programmed the phy before we had successfully looked up the clock rate.
Also, we were only checking that we had a valid configuration for the
currctrl register.
Move all these lookups to the start of this function instead, so we can
check that all lookups were successful before beginning to program the
phy.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Describe capabilities of the HLCDC IP found on sama5d4 SoCs and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Describe capabilities of the HLCDC IP found on at91sam9n12 SoC and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Describe capabilities of the HLCDC IP found on at91sam9x5 SoCs and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The atmel-hlcdc driver already supports atomic operations, add the
missing DRM_ATOMIC flag to expose the atomic features to userspace.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Pagetables can be moved and therefore the page directory update can be necessary
for the current cs even if none of the the bo's are moved. In that scenario
there is no fence between the sdma0 and gfx ring, so we add one.
v2 (chk): rebased
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Rework run queue implementation, especially remove the odd list handling.
v2: cleanup the code only, no algorithem change.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
bo_list_clone() will take a lot of time when bo_list hold too much
elements, like above 7000
Signed-off-by: Monk.Liu <monk.liu@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
remaining timeout returned by amdgpu_fence_wait_any can be larger than
max int value, thus the truncated 32 bit value in r ends up being
negative while its original long value is positive.
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
fix fence is released when pass to **fence sometimes.
add reference for it.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
