This patch adds a check whether LLDP Agent's default AdminStatus is
enabled or disabled on a given port. If it is disabled then it sets
the DCBX status to disabled as well; and would not query firmware for
any DCBX configuration data.
Change-ID: I73c0b9f0adbf4cae177d14914b20a48c9a8f50fd
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch allows i40e driver to query and use DCB configuration from
firmware when firmware DCBX agent is in CEE mode.
Change-ID: I30f92a67eb890f0f024f35339696e6e83d49a274
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are DCB configuration changes based on DCBX the firmware suspends
the port's Tx and generates an event to the PF. The PF is then responsible
to reconfigure the PF VSIs and switching topology as per the updated DCB
configuration and then resume the port's Tx by calling the "Resume Port Tx"
AQ command.
This patch adds this call to the flow that handles DCB re-configuration in
the PF.
Change-ID: I5b860ad48abfbf379b003143c4d3453e2ed5cc1c
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bumping minor version as this will be the second SW release and it
should be 1.
Change-ID: If0bd102095d2f059ae0c9b7f4ad625535ffbbdee
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF interrupt processing takes a looooong time, and it's possible that we
could lose a VFLR event if it happens while we're processing a VFLR on
another VF. This would leave the VF in a semi-permanent reset state,
which would not be cleared until yet another VF experiences a VFLR.
To correct this situation, we enable the VFLR interrupt cause before we
begin processing any pending resets. This means that any VFLR that
occurs during reset processing will generate another interrupt and this
routine will get called again.
This change may cause a spurious interrupt when multiple VFLRs occur
very close together in time. If this happens, then this routine will be
called again and it will detect no outstanding VFLR events and do
nothing. No harm, no foul.
Change-ID: Id0451f3e6e73a2cf6db1668296c71e129b59dc19
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Only warn once that PTP is not supported when linked at 100Mbit.
Yes, using a static this way means that this once-only message is not
port specific, but once only for the life of the driver, regardless of
the number of ports. That should be plenty.
Change-ID: Ie6476530056df408452e195ef06afd4f57caa4b2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Also provide ethtool -x support to fetch RSS key
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key increases attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX_IN_SEL offset for the CPSW_PORT/TX_IN_CTL register was
incorrect. This caused the Dual MAC mode to never get set when
it should. It also caused possible unintentional setting of a
bit in the CPSW_PORT/TX_BLKS_REM register.
The purpose of setting the Dual MAC mode for this register is to:
"... allow packets from both ethernet ports to be written into
the FIFO without one port starving the other port."
- AM335x ARM TRM
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We now allow up to 126 VFs. Note though that certain firmware
versions only allow up to 80 VFs. Moreover, old HCAs only support 64 VFs.
In these cases, we limit the maximum number of VFs to 64.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the driver queried the firmware in order to get the number
of supported EQs. Under SRIOV, since this was done before the driver
notified the firmware how many VFs it actually needs, the firmware had
to take into account a worst case scenario and always allocated four EQs
per VF, where one was used for events while the others were used for completions.
Now, when the firmware supports the asymmetric allocation scheme, denoted
by exposing num_sys_eqs > 0 (--> MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the
QUERY_FUNC command to query the firmware before enabling SRIOV. Thus we
can get more EQs and MSI-X vectors per function.
Moreover, when running in the new firmware/driver mode, the limitation
that the number of EQs should be a power of two is lifted.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QUERY_FUNC firmware command could be used in order to query the
number of EQs, reserved EQs, etc for a specific function.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor mlx4_load_one, as a preparation step for a new and
more complicated load function. The goal is to support both
newer firmware that required init_hca to be done before
enable_sriov and legacy firmwares that requires things to
be done the other way around.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactoring mlx4_cmd_init and mlx4_cmd_cleanup such that partial init
and cleanup are possible. After this refactoring, calling mlx4_cmd_init
several times is safe.
This is necessary in the VF init flow when mlx4_init_hca returns -EACCESS,
we need to issue cleanup and re-attempt to call it with the slave flag.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've used an incorrect type for the loop counter and the
mlx4_QUERY_FUNC_CAP function. The current input modifier
is either a port or a boolean.
Since the number of ports is always a positive value < 255,
we should use u8 instead of an integer with casting.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We mistakenly read the reserved_eqs field as a standard
numeric value rather than a log2 value.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), the PHY device will be put in a low-power mode using
BMCR_PDOWN if the the interface is set down. The smsc911x driver does
a software_reset opening the device driver (ndo_open). In such case,
the PHY must be powered-up before access to any register and before
calling the software_reset function. Otherwise, as the PHY is powered
down the software reset fails and the interface can not be enabled
again.
This patch fixes this scenario that is easy to reproduce setting down
the network interface and setting up again.
$ ifconfig eth0 down
$ ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a missing break statement so we set everything to
PKT_HASH_TYPE_L3 even when we intended to use PKT_HASH_TYPE_L4.
Fixes: 5b9dfe299e ('amd-xgbe: Provide support for receive side scaling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased delay in the smsc911x_phy_disable_energy_detect (from 1ms to 2ms).
Dropped delays in the smsc911x_phy_enable_energy_detect (100ms and 1ms).
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
I saw problems with soft reset due to wrong udelay timings.
After I fixed udelay, I measured the time needed to bring integrated PHY
from power-down to operational mode (the time beetween clearing EDPWRDOWN
bit and soft reset complete event). I got 1ms (measured using ktime_get).
The value is equal to the current value (1ms) used in the
smsc911x_phy_disable_energy_detect. It is near the upper bound and in order
to avoid rare soft reset faults it is doubled (2ms).
I don't know official timing for bringing up integrated PHY as specs doesn't
clarify this (or may be I didn't found).
It looks safe to drop delays before and after setting EDPWRDOWN bit
(enable PHY power-down mode). I didn't saw any regressions with the patch.
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch affect SMSC LAN generation 4 chips with integrated PHY (LAN9221).
It is possible that PHY could enter power-down mode (ENERGYON clear),
between ENERGYON bit check in smsc911x_phy_disable_energy_detect and SRST
bit set in smsc911x_soft_reset. This could happen, for example, if someone
disconnect ethernet cable between the checks. The PHY in a power-down mode
would prevent the MAC portion of chip to be software reseted.
Initially found by code review, confirmed later using test case.
This is low probability issue, and in order to reproduce it you have to
run the script:
while true; do
ifconfig eth0 down
ifconfig eth0 up || break
done
While the script is running you have to plug/unplug ethernet cable many
times (using gpio controlled ethernet switch, for example) until get:
[ 4516.477783] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.512207] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.524658] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4516.559082] smsc911x smsc911x.0: eth0: SMSC911x/921x identified at 0xce006000, IRQ: 336
[ 4516.571990] ADDRCONF(NETDEV_UP): eth0: link is not ready
ifconfig: SIOCSIFFLAGS: Input/output error
The patch was reviewed by Steve Glendinning and Microchip Team.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactored all macros used in cxgb4i as part of previously started cxgb4 macro
names cleanup. Makes them more uniform and avoids namespace collision.
Minor changes in other drivers where required as some of these macros are used
by multiple drivers, affected drivers are iw_cxgb4, cxgb4(vf) & csiostor
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. bcm_sysport_tx_poll()
always returns 0 whether or not we completed the poll quantum.
Fix this by returning either 0 when we did complete the TX ring reclaim,
or budget to trigger a repoll.
Fixes: d75b1ade56 ("net: less interrupt masking in NAPI")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. In tx napi poll we always return 0.
So tx napi is not called again and we do not clean up the tx ring.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the types of the descriptor entries in the xgbe_ring_desc struct
from u32 to __le32 to fix endian warnings issued by sparse.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to ensure the net_device's dev.parent is set before we used it
in dma_zalloc_coherent() from init_hash_table().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae5c6c6d "ptp: Classify ptp over ip over vlan packets" changed the
code in two drivers that matches time stamps with PTP frames, with the goal
of allowing VLAN tagged PTP packets to receive hardware time stamps.
However, that commit failed to account for the VLAN header when parsing
IPv4 packets. This patch fixes those two drivers to correctly match VLAN
tagged IPv4/UDP PTP messages with their time stamps.
This patch should also be applied to v3.17.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static checker warning that got introduced in commit e2ac962895
("cxgb4: Cleanup macros so they follow the same style and look consistent, part
2") due to accidental checkin of bogus line.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* In LLD_MANAGED mode, traffic classes were being returned in reverse order to
lldp agent.
* Priotype of strict is no longer the default returned.
* Change behaviour of getdcbx() based on discussions on lldp-devel
These were missed as there was no working fetch interface for open-lldp when
running in LLD_MANAGED mode till now.
Fixes: 76bcb31efc ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the bloated use of __skb_alloc_page and replace it with
__dev_alloc_page. In addition update the one other spot that is
allocating a page so that it allocates with the correct flags.
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.
Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.
Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.
This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the dependency of the VENDOR entry and fixes
the QCA7000 one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
