Hook the Broadcom SYSTEMPORT driver into the build system under the
SYSTEMPORT Kconfig symbol.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT is the latest Ethernet MAC hardware block used on newer
BCM7xxx Set Top Box SoCs in conjunction with an internal Ethernet
switch. This patch adds support for this hardware block along with the
following hardware features:
- support for hardware checksum offload (transmit and receive)
- support for the 32 transmit queues
- MIB counters reading
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the PTP Tx timestamp interrupt handler. The original
code misinterpreted the interrupt handler design. We were clearing the
ena_mask bit for the Timesync interrupts. This is done to indicate that
the interrupt will be handled in a scheduled work item (instead of
immediately) and that work item is responsible for re-enabling the
interrupts. However, the Tx timestamp was being handled immediately and
nothing was ever re-enabling it. This resulted in a single interrupt
working for the life of the driver.
This patch fixes the issue by instead clearing the bit from icr0 which
is used to indicate that the interrupt was immediately handled and can
be re-enabled right away. This patch also clears up a related issue due
to writing the PRTTSYN_STAT_0 register, which was unintentionally
clearing the cause bits for Timesync interrupts.
Change-ID: I057bd70d53c302f60fab78246989cbdfa469d83b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the name used by Ethtool to something more
conventional in preparation for TSE Ethtool register dump
support to be added in the near future.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a fault in the error recovery path of the probe
routine where the netdev structure was not being unregistered properly
leading to a panic only when the phy probe failed.
Abbreviated panic stack seen is as follows:
(free_netdev+0xXX) from (altera_tse_probe+0xXX)
(altera_tse_probe+0xXX) from (platform_drv_probe+0xXX)
(platform_drv_probe+0xXX) from (driver_probe_device+0xXX)
(driver_probe_device+0xXX) from (__driver_attach+0xXX)
(__driver_attach+0xXX) from (bus_for_each_dev+0xXX)
(bus_for_each_dev+0xXX) from (driver_attach+0xXX)
(driver_attach+0xXX) from (bus_add_driver+0xXX)
(bus_add_driver+0xXX) from (driver_register+0xXX)
(driver_register+0xXX) from (__platform_driver_register+0xXX)
(__platform_driver_register+0xXX) from (altera_tse_driver_init+0xXX)
(altera_tse_driver_init+0xXX) from (do_one_initcall+0xXX)
(do_one_initcall+0xXX) from (kernel_init_freeable+0xXX)
(kernel_init_freeable+0xXX) from (kernel_init+0xXX)
(kernel_init+0xXX) from (ret_from_fork+0xXX)
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch initializes the pause quanta set for transmitted pause frames
to the IEEE specified default of 0xffff.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch works around a recently discovered unaligned receive dma problem
with the Altera SGMDA. The Altera SGDMA component cannot be configured to
DMA data to unaligned addresses for receive packet operations from the
Triple Speed Ethernet component because of a potential data transfer
corruption that can occur. This patch addresses this issue by
utilizing the shift 16 bits feature of the Altera Triple Speed Ethernet
component and modifying the receive buffer physical addresses accordingly
such that the target receive DMA address is always aligned on a 32-bit
boundary.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Tested-by: Matthew Gerlach <mgerlach@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 2dc33bbc "bnx2x: Remove the sriov VFOP mechanism",
the bnx2x started enforcing vlan credits for all vlan configurations.
This exposed 2 issues:
- Vlan credits are not returned once a VF is removed; this causes a leak
of credits, and eventually will lead to VFs with no vlan credits.
- A vlan credit must be set aside for the Hypervisor to use, and should
not be visible to the VF.
Although linux VFs at the moment do not support vlan configuration [from the
VF side] which causes them to be resilient to this sort of issue, Windows VF
over linux hypervisors might fail to load as the vlan credits become depleted.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VF interface, the driver fails to release that VF's mailbox
and bulletin board allocated memory.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the ARRAY_SIZE macro to determine the number of entries in
bcm_enet_gstrings_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a seg fault on 'ethtool -A' entry if the
interface is down. Obviously we need to have the
phy device initialized / "connected" (see of_phy_connect())
to be able to advertise pause frame capabilities.
Fixes: 23402bddf9
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In case QLC_83XX_MBX_CMD_NO_WAIT command type the calling
function does not free the memory as it does not wait for
response. So free it when get a response from adapter after
sending the command.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware versions fails to reset the lock during
initialization. Force reset firmware API lock during driver
probe to ensure lock availability.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/igb/e1000_mac.c
net/core/filter.c
Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine some macros that were conditioned upon SMC_DEBUG level.
By allowing compiler to verify parameters used by these macros
unconditionally, we can flag compilation failures.
Compiler will still optimize out the unused code path depending on
SMC_DEBUG, so this is a net gain.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to ixgbe, ixgbevf, e1000e, igb and i40e.
Jacob converts the ixgbe low_water into an array which allows the
algorithm to output different values for different TCs and we can
distinguish between them. Removes vlan_filter_disable() and
vlan_filter_enable() in ixgbe so that we can do the work directly in
set_rx_mode(). Changes the setting of multicast filters only when
the interface is not in promiscuous mode for multicast packets in
ixgbe. Improves MAC filter handling by adding mac_table API based
on work done for igb, which includes functions to add/delete MAC
filters.
Mark changes register reads in ixgbe to an out-of-line function since
register reads are slow.
Emil provides a ixgbevf patch to update the driver description since
it supports more than just 82599 parts now.
David provides several cleanup patches for e1000e which resolve some
checkpatch issues as well as changing occurrences of returning 0 or 1 in
bool functions to returning true false or true.
Carolyn provides several cleanup patches for igb which fix checkpatch
warnings.
Mitch provides a fix for i40evf where the driver would correctly allow
the virtual function link state to be controlled by 'ip set link', but
would not report it correctly back. This is fixed by filling out
the appropriate field in the VF info struct.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This should make the driver usable with VIA/WonderMedia ARM-based
Systems-on-Chip integrated Rhine III adapters. Note that these
are always in MMIO mode, and don't have any known EEPROM.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more generic data structures instead of struct pci_dev wherever
possible in preparation for OF bus binding
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove legacy PCI DMA wrappers and instead use generic DMA functions
directly in preparation for OF bus binding
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the driver would correctly allow the VF link state to be
controlled by 'ip set link', it would not report it correctly back.
Fix this by filling out the appropriate field in the vf info struct.
Change-ID: I58d8e356438190e1ee9660b424301af6f416cdbe
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes WARNING:LEADING_SPACE, WARNING:SPACING, ERROR:SPACING,
WARNING:SPACE_BEFORE_TAB and ERROR_CODE_INDENT from checkpatch file check.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add mac_table API based on work done for igb, which includes functions
to add and delete mac filters. This simplifies code for various entities
that use MAC filters such as VMDQ, SR-IOV, MACVLAN, and such.
Reported-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In line with changes done by Alex Duyck regarding unicast filters, we
now only set multicast filters when the interface is not in promiscuous
mode for multicast packets. This also has an impact on the RAR usage
such that SR-IOV has some RARs reserved for its own usage.
Reported-by: Alex Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously these functions handled stripping setup as well, but this has
already been removed from these functions. Rather than encapsulating
this into a function, we can just do the work directly in set_rx_mode.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Register reads are slow, so don't inline them.
Size before:
text data bss dec hex filename
226337 8280 552 235169 396a1 ixgbe.ko
Size after:
text data bss dec hex filename
194578 8280 552 203410 31a92 ixgbe.ko
for about a 14% reduction in text size.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since fc.high_water is an array, we should treat low_water as an array
also. This allows the algorithm to output different values for different
TCs, and then we can distinguish between them. In addition, this patch
changes one path that didn't honor the return value from ixgbe_setup_fc.
Reported-by: Aaron Salter <aaron.k.salter@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
