This moves byte count tables to tx domain removing completely
ambivalent shared data. Changes handling of allocation
byte count tables and keep warm consistent memory
Moves general tx scheduler definitions from iwl-4956-hw.h
to iwl-fh.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves rx status/read registers into
iwl_rx_queue structures. This solution is more memory
hungry but is more structured and provides needed RX/TX
separation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch doesn't fail power save setting when calibration is
not done yet. The new power index is registered and will
be evaluated again anyway upon calibration completion.
This patch also eliminates WARN_ON in mac80211 hw_config during
initialization
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So I dug deeper into the DMA problems I had with iwlagn and a kind soul
helped me in that he said something about pci-e alignment and mentioned
the iwl_rx_allocate function to check for crossing 4KB boundaries. Since
there's 8KB A-MPDU support, crossing 4k boundaries didn't seem like
something the device would fail with, but when I looked into the
function for a minute anyway I stumbled over this little gem:
BUG_ON(rxb->dma_addr & (~DMA_BIT_MASK(36) & 0xff));
Clearly, that is a totally bogus check, one would hope the compiler
removes it entirely. (Think about it)
After fixing it, I obviously ran into it, nothing guarantees the
alignment the way you want it, because of the way skbs and their
headroom are allocated. I won't explain that here nor double-check that
I'm right, that goes beyond what most of the CC'ed people care about.
So then I came up with the patch below, and so far my system has
survived minutes with 64K pages, when it would previously fail in
seconds. And I haven't seen a single instance of the TX bug either. But
when you see the patch it'll be pretty obvious to you why.
This should fix the following reported kernel bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11596http://bugzilla.kernel.org/show_bug.cgi?id=11393http://bugzilla.kernel.org/show_bug.cgi?id=11983
I haven't checked if there are any elsewhere, but I suppose RHBZ will
have a few instances too...
I'd like to ask anyone who is CC'ed (those are people I know ran into
the bug) to try this patch.
I am convinced that this patch is correct in spirit, but I haven't
understood why, for example, there are so many unmap calls. I'm not
entirely convinced that this is the only bug leading to the TX reply
errors.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.
Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.
Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.
Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)
I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.
Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 supports multiple virtual interfaces for a single device. For
example, a managed interface (wlan0) and a monitor interface (mon0) can
exist at the same time. Thus priv->iw_mode is not sufficient to track
the wireless mode any more. The patch redefines priv->iw_mode as the
first interface mode (the same as priv->vif->type if priv->vif != NULL).
If another monitor type interface is created later, we don't change
priv->iw_mode into monitor. This way, the original interface still
works. The patch also requests mac80211 to do reassociation after we
change the Rx filter flags.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up FH bits and adds missing register values
that will be used later in TX initialization rewrite
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I added this comment myself, but it's clearly wrong. I had meant
to place it in iwl_mac_add_interface, which at the time didn't
honour the MAC address setting, but it does now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the SSID from the driver API since now there is no
driver that requires knowing the SSID and I think it's
unlikely that any hardware design that does require the
SSID will play well with mac80211.
This also removes support for setting the SSID in master
mode which will require a patch to hostapd to not try.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an undirected scan is requested and iwlwifi is not associated but
the user has set an SSID (and maybe was associated with that network at
some point) then iwlwifi will assume the user wanted to scan for this
SSID which seems wrong. Remove this code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Was wondering about this code since supposedly the firmware will
add the SSID element. Turns out it's dead, so remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes iwl3945 deadlock during suspend by moving notify_mac out
of iwl3945 mutex. This is a portion of the same fix for iwlwifi by Tomas.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures we clear any scan status bit when
an error occurs while sending the scan command. It is
the implementation of patch:
"iwlwifi: clear scanning bits upon failure"
for iwl3945.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_tasklet_handler -> __ieee80211_rx ->
__ieee80211_rx_handle_packet -> ieee80211_invoke_rx_handlers ->
ieee80211_rx_h_decrypt -> ieee80211_crypto_tkip_decrypt ->
ieee80211_tkip_decrypt_data -> iwl4965_mac_update_tkip_key ->
iwl_scan_cancel_timeout -> msleep
Ooops!
Avoid the sleep by changing iwl_scan_cancel_timeout with
iwl_scan_cancel and simply returning on failure if the scan persists.
This will cause hardware decryption to fail and we'll handle a few more
frames with software decryption.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reclaim flag should include REPLY_RX_MPDU_CMD in the list of commands
issued by uCode. This is for safety in case the SEQ_RX_FRAME bit is set
incorrectly.
Signed-off-by: Daniel Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch drops unreadable usage of IWL_SET/GET_BITS16 in byte count
tables handling
This patch also cleans a bit the byte count table code and adds
WARN_ON traps on invalid values
This patch is pure cleanup, no functional changes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwl_bg_request_scan function, if we could not send a
scan command it will go to done.
In done it does the right thing to call mac80211 with
scan complete, but the problem is STATUS_SCAN_HW is still
set causing any future scan to fail. Fix by clearing the scanning status
bits if scan fails.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since calibration framework is not HW specific remove 5000 and 4965 prefix
This patch doesn't provide any functional changes only code renaming
and movement
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch utilize 5000 new TX response command
which contains all necessary information and avoids
back referencing to the original TX frame.
It also change handling of software queue tracking
4965 flow is aligned with changes as much as possible.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.
This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs_create_bool() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"Clearing" the rate control algorithm is pointless, none of
the algorithms actually uses this operation and it's not even
invoked properly for all channel switching. Also, there's no
need to since rate control algorithms work per station.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch:
1. fixes command DMA unmapping, this might be visible only
on platforms where DMA unmapping is no noop such as PPC64 (not tested)
2. attaches correctly high memory part of the host command buffer
3. changes structure of TFD TB
instead of describing transmit buffer (TB) tuple it describes single
TB and makes code more readable on price of one unaligned access
4. eliminates using of IWL_GET/SET_BITs for TFD handling
5. renames TFD structures to mach the HW spec
6. reduces iwl_tx_info size by reserving first TB to the host command
This patch should not have any visible effect on x86 32
This patch is rework of
iwlwifi: fix DMA code and bugs from
Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
