If multiple segments belonging to an isoc transfer are submitted
concurrently, the isoc_frame_index field in struct wa_xfer can get
corrupted. This patch moves the isoc_frame_index field from struct
wa_xfer to struct wa_seg to prevent this from happening.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use USB_CTRL_SET_TIMEOUT and USB_CTRL_GET_TIMEOUT for USB control
messages instead of an arbitrary 1s timeout value. This is particularly
useful for WUSB since in the worst case RF scanario, a WUSB device can
be unresponsive for up to 4s and still be connected.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to skip querying the config and string descriptors for
unauthorized WUSB devices when usb_new_device is called. It is allowed
by WUSB spec. The only action that needs to be delayed until
authorization time is the set config. This change allows user mode
tools to see the config and string descriptors earlier in enumeration
which is needed for some WUSB devices to function properly on Android
systems. It also reduces the amount of divergent code paths needed
for WUSB devices.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usb_submit_urb, do not fail if an isoc URB for a wireless USB device
has an interval < 6. Per WUSB spec, isoc endpoints can support values
from 1-16. Valid values for interrupt URBs for wireless USB devices are
still 6-16.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a URB is broken up into multiple transfer segments and a short
transfer occurs in any segment other than the last, the URB will
currently get stuck in the driver forever. This patch adds a check for
a short transfer and cleans up any pending segments so the URB can
complete properly.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we connect Male-A-To-Male-A cable between otg-host and host pc,
the ci->vbus_active is set wrongly, and cause the controller run
at peripheral mode when we load gadget module (ci_udc_start will be run),
but the software runs at host mode due to id = 0. The ehci_irq
can't handle suspend (USBi_SLI) interrupt which is enabled for
peripheral mode, it causes no one will handle irq error.
This patch is needed for 3.12 stable
Cc: stable <stable@vger.kernel.org>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZTE AC2726 EVDO modem drops ppp connection every minute when driven by
zte_ev but works fine when driven by option. Move the support for AC2726
back to option driver.
Signed-off-by: Dmitry Kunilov <dmitry.kunilov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_add_phy_dev instead of usb_add_phy, so that devices can
be bound to the phy. This is needed to set up USB phy for
some internal PCI USB host controllers on R-Car Gen2.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe writes:
usb: fixes for v3.13-rc4
DWC3 learned that it can't resume a PHY which wasn't
initialized and it also learned to not leave PHY powered
up in case of an error.
twl6030-usb PHY driver got a fix for a signedness bug in
twl6030_readb().
Tegra PHY driver got a bug fix where it could return success
even though there was an error.
Signed-of-by: Felipe Balbi <balbi@ti.com>
the lock was only taken inside the hardirq
handler, which runs with IRQs disabled. There's
no chance of any race condition happening, even
on SMP machines. It's safe to remove that
spinlock.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 614ced91fc.
The units on this was seen were prototypes and the issue is
not seen on younger units.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Individual controller driver has different requirement for wakeup
setting, so move it from core to itself. In order to align with
current etting the default wakeup setting is enabled (except for
chipidea host).
Pass compile test with below commands:
make O=outout/all allmodconfig
make -j$CPU_NUM O=outout/all drivers/usb
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX51 as the next user of the usbmisc driver.
Functionality is similar to i.MX53, so at this stage simply
reuse existing i.MX53 calls.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ci_hdrc_imx's probe needs usbmisc_imx to be loadded beforehand,
so it is better we load usbmisc_imx first.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regmap only needs to reallocate if the hw_read on the CAP register shows
lpm is used. Therefore the if() statement check the change.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds external USB phy support to USB HCD driver that
allows to find and initialize external USB phy, bound to
the HCD, when the HCD is added.
The usb_add_hcd function returns -EPROBE_DEFER if the USB
phy, bound to the HCD, is not ready.
If no USB phy is bound, the HCD is initialized as usual.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds remove_phy flag to the HCD structure. If the flag is
set and if hcd->phy is valid, the phy is shutdown and released
whenever usb_add_hcd fails or usb_hcd_remove is called.
This can be used by the HCD drivers to auto-remove
the external USB phy when it is no longer needed.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add calls to usb_hcd_link_urb_to_ep, usb_hcd_unlink_urb_from_ep, and
usb_hcd_check_unlink_urb in the appropriate locations.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-spear glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-spear suspend scenario.
Calling explicitly the ohci_suspend() routine in
spear_ohci_hcd_drv_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-da8xx glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-da8xx suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_da8xx_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-usb@vger.kernel.or
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-at91 glue was not properly handled
as it was not suspending generic part of ohci controller. Alan Stern
suggested, properly handle ohci-at91 suspend scenario.
Calling explicitly the ohci_suspend() routine in ohci_hcd_at91_drv_suspend()
will ensure proper handling of suspend scenario. This task is sugested
by Alan Stern.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of OHCI was not properly
handled in ochi_suspend()routine. Alan Stern
suggested, properly handle OHCI suspend scenario.
This does generic proper handling of suspend
scenario to all OHCI SOC.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit "usb: usbtest: support bos descriptor test for usb 3.0"
introduced a test for bos descriptor. And USB 2.1 device also can be
checked. So this patch extends the test coverage to support USB 2.1 device.
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.1 Link PM adds to use bits[1:15] according to USB 2.0 ECN Errata for
Link Power Management spec.
Bit Encoding
0 Reserved
1 LPM
2 BESL & Altemate HIRD definitions supported
3 Recommended Baseline BESL valid
4 Recommended Deep BESL valid
11:8 Recommended Baseline BESL value
15:12 Recommended Deep BESL value
31:16 Reserved
So fix the bit mask from 0x1e to 0xfffe.
Reported-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Test 10 of usbtest module, it queues multiple control messages and
thereby tests control message queuing, protocol stalls, short reads, and
fault handling. And this patch add a test case to support queue BOS control
request for USB 3.0 SPEC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the .find_device function pointer in struct acpi_bus_type
with a new one, .find_companion, that is supposed to point to a
function returning struct acpi_device pointer (instead of an int)
and takes one argument (instead of two). This way the role of
this callback is more clear and the implementation of it can
be more straightforward.
Update all of the users of struct acpi_bus_type (PCI, PNP/ACPI and
USB) to reflect the structure change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Lan Tianyu <tianyu.lan@intel.com> # for USB/ACPI
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add Tahvo USB transceiver driver.
Based on old code from linux-omap tree. The original driver was written
by Juha Yrjölä, Tony Lindgren, and Timo Teräs.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Transceivers need to manage OTG controller state on OMAP1 to enable
switching between peripheral and host modes. Provide a driver for that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/host/ehci-mv.c:181:26-27: WARNING comparing pointer to 0, suggest !E
/c/kernel-tests/src/cocci/drivers/usb/host/ehci-mv.c:181:26-27: WARNING comparing pointer to 0
Compare pointer-typed values to NULL rather than 0
Semantic patch information:
This makes an effort to choose between !x and x == NULL. !x is used
if it has previously been used with the function used to initialize x.
This relies on type information. More type information can be obtained
using the option -all_includes and the option -I to specify an
include path.
Generated by: coccinelle/null/badzero.cocci
CC: Jingoo Han <jg1.han@samsung.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
This patch adds a check for USB_STATE_NOTATTACHED to the
hub_port_warm_reset_required() workaround for ports that end up in
Compliance Mode in hub_events() when trying to decide which reset
function to use. Trying to call usb_reset_device() with a NOTATTACHED
device will just fail and leave the port broken.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include linux/dma-mapping.h to make the new functions available that are
used since 22d9d8e83 ("DMA-API: usb: use dma_set_coherent_mask()").
drivers/usb/host/ohci-pxa27x.c: In function ‘ohci_pxa_of_init’:
drivers/usb/host/ohci-pxa27x.c:310:2: error: implicit declaration of function ‘dma_coerce_mask_and_coherent’ [-Werror=implicit-function-declaration]
drivers/usb/host/ohci-pxa27x.c:310:2: error: implicit declaration of function ‘DMA_BIT_MASK’ [-Werror=implicit-function-declaration]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
