Use the new lane config in dsi_cio_enable_lane_override(). The function
parameters are also slightly changed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the new lane config in dsi_cio_wait_tx_clk_esc_reset(). This also
extends the function to support 5 lanes on OMAP4, instead of 3 lanes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Parse the lane configuration from the device data into internal lane
config format. This will be used in the following patches to clean up
the lane handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI driver currently counts used lanes and number of supported lanes by
using the number of data lanes (i.e. excluding clock lane). This patch
changes this to use the number of all lanes so that the following lane
config patches are cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Flush posted write in _enable_lcd_out() and _enable_digit_out(). This
ensures the the lcd/digit bit is written before the code starts waiting
for interrupts about enabling/disabling the output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Flush posted write after setting the bit to send the BTA to ensure the
BTA is sent right away, as the code in dsi_vc_send_bta_sync() waits for
an interrupt caused indirectly by sending the BTA.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add data for the FocalTech ETM070003DH6 display to the generic_dpi_panel
display driver.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A DRM display driver for TI OMAP platform. Similar to omapfb (fbdev)
and omap_vout (v4l2 display) drivers in the past, this driver uses the
DSS2 driver to access the display hardware, including support for
HDMI, DVI, and various types of LCD panels. And it implements GEM
support for buffer allocation (for KMS as well as offscreen buffers
used by the xf86-video-omap userspace xorg driver).
The driver maps CRTCs to overlays, encoders to overlay-managers, and
connectors to dssdev's. Note that this arrangement might change slightly
when support for drm_plane overlays is added.
For GEM support, non-scanout buffers are using the shmem backed pages
provided by GEM core (In drm_gem_object_init()). In the case of scanout
buffers, which need to be physically contiguous, those are allocated
with CMA and use drm_gem_private_object_init().
See userspace xorg driver:
git://github.com/robclark/xf86-video-omap.git
Refer to this link for CMA (Continuous Memory Allocator):
http://lkml.org/lkml/2011/8/19/302
Links to previous versions of the patch:
v1: http://lwn.net/Articles/458137/
v2: http://patches.linaro.org/4156/
v3: http://patches.linaro.org/4688/
v4: http://patches.linaro.org/4791/
History:
v5: move headers from include/drm at Greg KH's request, minor rebasing
on 3.2-rc1, pull in private copies of drm_gem_{get,put}_pages()
because "drm/gem: add functions to get/put pages" patch is not
merged yet
v4: bit of rework of encoder/connector _dpms() code, modeset_init()
rework to not use nested functions, update TODO.txt
v3: minor cleanups, improved error handling for dev_load(), some minor
API changes that will be needed later for tiled buffer support
v2: replace omap_vram with CMA for scanout buffer allocation, remove
unneeded functions, use dma_addr_t for physical addresses, error
handling cleanup, refactor attach/detach pages into common drm
functions, split non-userspace-facing API into omap_priv.h, remove
plugin API
v1: original
Signed-off-by: Rob Clark <rob@ti.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While the OLPC display appears to be able to handle either positive
or negative sync, the Display Controller only recognises positive sync.
This brings viafb (for XO-1.5) in line with lxfb (for XO-1) and
fixes a recent regression where the XO-1.5 DCON could no longer be
frozen. Thanks to Florian Tobias Schandinat for helping identify
the fix.
Test case: from a vt,
echo 1 > /sys/devices/platform/dcon/freeze
should cause the current screen contents to freeze, rather than garbage being
displayed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@kernel.org
Patch follows the disable and software reset sequence specified
in version2 to LCDC functional specification.
Without this flicker is observed on re-enabling the LCDC.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
SH MIPI manual explains the calculation method of HBP/HFP.
it is based on HSbyteCLK settings.
SH73a0 chip can use HS6divCLK/HS4divCLK for it.
This patch has compatibility to SH7372 mipi
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
VMLEN1/VMLEN2 needs blanking length which is calculated from
video image size.
The calculation methods are explained on
[SH MIPI] - [Video Mode] - [Blanking Packet setting]
But HFPLEN (= VMLEN2) is un-understandable.
For example, if SH-MIPI input was RGB888 (3byte),
output was RGB888 (3byte)
and 3lane connection, the date goes straight.
But if SH-MIPI input was RGB888 (3byte),
output was RGB565 (2byte)
and 4lane connection, it needs delay in HFPLEN.
Then (input cycle - output cycle) * lane is necessary the delay
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Current code calculates scaling factors for video overlays even when the
overlays are not scaled. Change the code to skip calculations when not
scaling.
This optimizes the code a bit, but also fixes a problem when configuring
an overlay for a disabled display: if the display is disabled we don't
necessarily know the pixel clock used when the display is enabled, and
in some cases (like HDMI) the pixel clock is set to zero until a proper
video mode is set later. A wrong pixel clock will mess up the
scaling calculations, causing an error like:
omapdss DISPC error: failed to set up scaling, required fclk rate = 0
Hz, current fclk rate = 170666666 Hz
A proper fix would be to check later whether the clocks are enough for the
scaling, at the point when the overlay or display is actually enabled,
but this patch removes the problem for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix warnings similar to this by including module.h:
drivers/video/omap/dispc.c:276:1: warning: data definition has no type
or storage class
drivers/video/omap/dispc.c:276:1: warning: type defaults to 'int' in
declaration of 'EXPORT_SYMBOL'
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_get_pixel_clock() returns the pixel clock in Hz, but the pck is
stored as kHz. This means the return value has to be multiplied by 1000,
not by 10000 as the code did.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Transparency length is fixed for pixel blending in order to support
ARGB 8888 format.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Some Village Tronic Picasso IV graphics cards identify as a 64 MiB Zorro
device in Zorro III mode.
While the total graphics memory size is the same on such cards, the offset
of the graphics memory differs. Add a quirk to handle this.
Based on src/sys/arch/amiga/dev/grf_cl.c from NetBSD.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
In Zorro II mode, the Village Tronic Picasso IV graphics card shows up as
either 2 or 3 Zorro devices:
- One for the registers of the Cirrus Logic graphics chip,
- One for the first bank of 2 MiB of graphics memory,
- An optional one for the second bank of 2 MiB of graphics memory,
if there was enough free Zorro II address space.
Based on src/sys/arch/amiga/dev/grf_cl.c from NetBSD.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As indicated by commit a7f4d00a82 ("zorro:
Defer device_register() until all devices have been identified"), cirrusfb
crashes if zorro_find_device() cannot find an expected device.
Rewrite the Zorro device probe code to make it more robust, easier to
understand, and more extensible.
Other logical changes:
- For cards that show up as 2 Zorro devices, autoprobe graphics memory
sizes based on the size of the Zorro device containing the graphics
memory.
Acording to the NetBSD sources, this is safe.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The newer Atmel SoCs use normal 16bit 565 BGR/RGB for the palette data,
rather than the special intensity + 555 format.
Fill out palette data correctly on these devices, and at the same time
respect the RGB/BGR wiring mode.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
If used with negative polarity the PWM unit cannot be disabled. This would
result in a full contrast screen.
Instead let the PWM unit enabled using 0x0 as compare value which darkens
the display.
In result no power saving is possible if inverted contrast polarity
is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
In the AT91SAM9263 Manual the HFP part in LCDTIM2 is described as follows:
* HFP: Horizontal Front Porch
Number of idle LCDDOTCK cycles at the end of the line.
Idle period is (HFP+2) LCDDOTCK cycles.
It is only a minor issue. I also changed all boards using atmel_lcdfb
I found to respect the new calculation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This four year old subsystem does not have a single in-tree user
not even in staging and as far as I know also none out-of-tree.
I think that justifies removing it which cleans the config up.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: James Simmons <jsimmons@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
