DMA will not stop when clearing enable bit till all transaction
is done. The bug is exposed in audio playback because ring DMA
chain never stop. Force hardware to stop with setting FORCE bit.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Align src and dst width to fix data alignment issue as
trailing single transaction that does not fill a full
burst require identical src/dst data width.
Burst length limitation can be addressed well too.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We cycle through all the "high performance" channels to distribute
load across the available CPUs. Process the NetworkDirect as a
high performance device.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hypervisor Top Level Functional Specification v3.1/4.0 notes that cpuid
(0x40000003) EDX's 10th bit should be used to check that Hyper-V guest
crash MSR's functionality available.
This patch should fix this recognition. Currently the code checks EAX
register instead of EDX.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pre-Win2012R2 hosts don't properly handle CHANNELMSG_UNLOAD and
wait_for_completion() hangs. Avoid sending such request on old hosts.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't catch this allocation failure because there is a typo and we
check the wrong variable.
Fixes: 14b50f80c3 ('Drivers: hv: util: introduce hv_utils_transport abstraction')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The guest may have to send a completion packet back to the host.
To support this usage, permit sending a packet without a payload -
we would be only sending the descriptor in this case.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support Win10 protocol for Dynamic Memory. Thia patch allows guests on Win10 hosts
to hot-add memory even when dynamic memory is not enabled on the guest.
Signed-off-by: Alex Ng <alexng@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct hv_start_fcopy is too big to be on stack on i386, the following
warning is reported:
>> drivers/hv/hv_fcopy.c:159:1: warning: the frame size of 1088 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kzalloc() return value check was accidentally lost in 11bc3a5fa9:
"Drivers: hv: kvp: convert to hv_utils_transport" commit.
We don't need to reset kvp_transaction.state here as we have the
kvp_timeout_func() timeout function and in case we're in OOM situation
it is preferable to wait.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
current_pt_regs() sometimes returns regs of the userspace process and in
case of a kernel crash this is not what we need to report. E.g. when we
trigger crash with sysrq we see the following:
...
RIP: 0010:[<ffffffff815b8696>] [<ffffffff815b8696>] sysrq_handle_crash+0x16/0x20
RSP: 0018:ffff8800db0a7d88 EFLAGS: 00010246
RAX: 000000000000000f RBX: ffffffff820a0660 RCX: 0000000000000000
...
at the same time current_pt_regs() give us:
ip=7f899ea7e9e0, ax=ffffffffffffffda, bx=26c81a0, cx=7f899ea7e9e0, ...
These registers come from the userspace process triggered the crash. As we
don't even know which process it was this information is rather useless.
When kernel crash happens through 'die' proper regs are being passed to
all receivers on the die_chain (and panic_notifier_list is being notified
with the string passed to panic() only). If panic() is called manually
(e.g. on BUG()) we won't get 'die' notification so keep the 'panic'
notification reporter as well but guard against double reporting.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Full kernel hang is observed when kdump kernel starts after a crash. This
hang happens in vmbus_negotiate_version() function on
wait_for_completion() as Hyper-V host (Win2012R2 in my testing) never
responds to CHANNELMSG_INITIATE_CONTACT as it thinks the connection is
already established. We need to perform some mandatory minimalistic
cleanup before we start new kernel.
Reported-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the very late stage of kexec a driver (which are not being unloaded) can
try to post a message or signal an event. This will crash the kernel as we
already did hv_cleanup() and the hypercall page is NULL.
Move all common (between 32 and 64 bit code) declarations to the beginning
of the do_hypercall() function. Unfortunately we have to write the
!hypercall_page check twice to not mix declarations and code.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When general-purpose kexec (not kdump) is being performed in Hyper-V guest
the newly booted kernel fails with an MCE error coming from the host. It
is the same error which was fixed in the "Drivers: hv: vmbus: Implement
the protocol for tearing down vmbus state" commit - monitor pages remain
special and when they're being written to (as the new kernel doesn't know
these pages are special) bad things happen. We need to perform some
minimalistic cleanup before booting a new kernel on kexec. To do so we
need to register a special machine_ops.shutdown handler to be executed
before the native_machine_shutdown(). Registering a shutdown notification
handler via the register_reboot_notifier() call is not sufficient as it
happens to early for our purposes. machine_ops is not being exported to
modules (and I don't think we want to export it) so let's do this in
mshyperv.c
The minimalistic cleanup consists of cleaning up clockevents, synic MSRs,
guest os id MSR, and hypercall MSR.
Kdump doesn't require all this stuff as it lives in a separate memory
space.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have hv_synic_free() which frees all per-cpu pages for all
CPUs, let's remove the hv_synic_free_cpu() call from hv_synic_cleanup()
so it will be possible to do separate cleanup (writing to MSRs) and final
freeing. This is going to be used to assist kexec.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most drivers need to set constraints on the buffer alignment for async tx
operations. However, even though it is documented, some drivers either use
a defined constant that is not matching what the alignment variable expects
(like DMA_BUSWIDTH_* constants) or fill the alignment in bytes instead of
power of two.
Add a new enum for these alignments that matches what the framework
expects, and convert the drivers to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Including access_ok.h causes the ia64:allmodconfig build (and maybe others)
to fail with
include/linux/unaligned/le_struct.h:6:19: error:
redefinition of 'get_unaligned_le16'
include/linux/unaligned/access_ok.h:7:19: note:
previous definition of 'get_unaligned_le16' was here
include/linux/unaligned/le_struct.h:26:20: error:
redefinition of 'put_unaligned_le32'
include/linux/unaligned/access_ok.h:42:20: note:
previous definition of 'put_unaligned_le32' was here
include/linux/unaligned/le_struct.h:31:20: error:
redefinition of 'put_unaligned_le64'
include/linux/unaligned/access_ok.h:47:20: note:
previous definition of 'put_unaligned_le64' was here
Include unaligned.h instead and leave it up to the architecture to decide
how to implement unaligned accesses.
Fixes: 8c4f136497 ("Staging: lustre: Use put_unaligned_le64")
Cc: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devtype structures are all declared as const.
Compiler does not complain because we cast
their pointers to save them in .driver_data.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently register the uart driver during device probe
which makes it hard to support more than one chip.
Move the driver registration to module init/exit time and
preallocate space for up to 8 lines (4-8 chips).
Reported-by: Michael Allwright <michael.allwright@upb.de>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation of supporting multiple devices we should save
the per-chip line number (0 or 1), because the uart_port line
will reflect system-wide uart number and will be offseted for
chips other than the first to register.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support ZTE uart with some registers differing offset.
Probe as platform device for not AMBA IP ID is
available on ZTE uart.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve LCRH register access decision as ARM PL011 lcrh
register serve as both TX and RX, while other SOC may
implement TX and RX function with separated register.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce register look up table as different SOC venders
may have different register offset for the some register.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far DMA mode were activated when only number of bytes to send was
equal or greater than min_dma_size. Due to requirement that DMA transaction
buffer should be aligned to cache line size, the excessive bytes were
written to FIFO before starting DMA transaction. The problem occurred
when FIFO size were smaller than cache alignment, because writing all
excessive bytes to FIFO would fail. It happened in DMA mode when PIO
interrupts disabled, which caused driver hung.
The solution is to test if buffer is alligned to cache line size before
activating DMA mode, and if it's not, running PIO mode to align buffer
and then starting DMA transaction. In PIO mode, when interrupts are
enabled, lack of space in FIFO isn't the problem, so buffer aligning
will always finish with success.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to some of serial ports can have FIFO size smaller than cache line
size, and because of need to align DMA buffer address to cache line size,
it's necessary to calculate minimum number of bytes for which we want
to start DMA transaction to be at least cache line size. The simplest
way to meet this requirement is to get maximum of cache line size and
FIFO size.
Cc: <stable@vger.kernel.org> # v3.18+
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial core does not use tty_port_open() or tty_port_close(); serial
core defines and extends it's own tty open() and close() methods
(uart_open() and uart_close(), respectively).
Remove the tty_port activate() and shutdown() initializations, and
the uart_port_activate() function, which is never called.
NB: uart_port_shutdown() is used by uart_close() => uart_shutdown()
call chain (but not via the tty_port methods).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_close() runs in non-atomic context only; use
spin_lock/unlock_irq instead of saving the interrupt state (which
== on).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to DesignWare 8250 spec, if auto flow control
mode is enabled, a change in CTS does not cause an interrupt,
so sw-assisted CTS flow control mode will not work properly.
There reported an GPS firmware download failure issue, and we
verified the root cause is, the default sw-assisted CTS flow
control mode can not work properly since no interrupt when got
CTS signal.
This patch is to enable auto CTS mode by defaut if CRTSCTS
is enable for DesignWare 8250 controller.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Documenation/serial/driver requests that the tx_empty callback should
return 0 if there are still chars in the fifo or shifter or TIOCSER_TEMT
(0x01) if no character is pending to be sent.
Fix the mpc52xx serial driver to not return MPC52xx_PSC_SR_TXEMP (i.e.
0x0800) but TIOCSER_TEMT as documented.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use the mctrl_gpio helpers, we change the DT bindings:
ri-gpios renamed to rng-gpios. cd-gpios renamed to dcd-gpios.
However, no in-tree dts/dtsi specifies these, so no worries.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus check on pm_runtime_active that prevented
disconnection from a client in case the device was resuming
from power gating but not yet active.
Fix regression introduced by
18901357e7
mei: disconnect on connection request timeout
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Access to the BQ24190's configurable charge type property (none, trickle,
fast) is being masked by an incorrect power_supply_property entry. After
applying this patch a new 'charge_type' property will appear in the
bq24190-charger sysfs folder backed up by getters/setters already
present in the driver.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The USB Battery Charging spec (BC1.2) suggests a dedicated
charging port can deliver from 0.5 to 5.0A at between 4.75 and 5.25
volts.
To choose the "correct" current voltage setting requires a trial
and error approach: try to draw current and see if the voltage drops
too low.
Even with a configured Standard Downstream Port, it may not be possible
to reliably pull 500mA - depending on cable quality and source
quality I have reports of charging failure due to the voltage dropping
too low.
To address both these concerns, this patch introduce incremental
current setting.
The current pull from VBUS is increased in steps of 20mA every 100ms
until the target is reached or until the measure voltage drops below
4.75V. If the voltage does go too low, the target current is reduced
by 20mA and kept there.
This applies to currents selected automatically, or to values
set via sysfs. So setting a large value will cause the maximum
available to be used - up to the limit of 1.7A imposed by the
hardware.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This allows AC charging to be turned off, much like usb charging.
"continuous" mode is not available though.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a 'continuous' option for usb charging which enables
the "linear" charging mode of the twl4030.
Linear charging does a good job with not-so-reliable power sources.
Auto mode does not work well as it switches off when voltage drops
momentarily. Care must be taken not to over-charge.
It was used with a bike hub dynamo since a year or so. In that case
there are automatically charging stops when the cyclist needs a break.
Original-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'off' or 'auto' to
/sys/class/power/twl4030_usb/mode
will now enable or disable charging from USB port. Normally this is
enabled on 'plug' and disabled on 'unplug'.
Unplug will still disable charging. 'plug' will only enable it if
'auto' if selected.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'max_current' sysfs attributes are created which allow the
max to be set.
Whenever a current source changes, the default is restored.
This will be followed by a uevent, so user-space can decide to
update again.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The twl4030 charger has two current sources, 'USB' and 'AC'
(presumably "Accessory Charger" because it isn't Alternating Current).
If 'AC' is providing current, we should set the current limit
differently to when it isn't (and so USB is used).
So split 'cur' into 'usb_cur' and 'ac_cur' and use accordingly.
Now we must review the current setting on any interrupt or USB
event which might indicate that the charger-source has changed.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds DEV_TO_DEV support for i.MX SDMA driver to support data
transfer between two peripheral FIFOs.
The per_2_per script requires two peripheral addresses and two DMA
requests, and it need to check the src addr and dst addr is in the SPBA
bus space or in the AIPS bus space.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
