With DPIO powergating active the DPLL can't be accessed unless
something else is keeping the common lane in the channel on.
That means the PPS kick procedure could fail to enable the PLL.
Power up some data lanes to force the common lane to power up
so that the PLL can be enabled temporarily.
v2: Avoid gcc uninitilized variable warning
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normmally the common lane in a PHY channel gets powered up when some
of the data lanes get powered up. But when we're driving port B with
pipe B we don't want to enabled any of the data lanes, and just want
the DPLL in the common lane to be active.
To make that happens we have to temporarily enable some data lanes
after which we can access the DPLL registers in the common lane. Once
the pipe is up and running we can drop the power override on the data
lanes allowing them to shut down. From this point forward the common
lane will in fact stay powered on until the data lanes in the other
channel get powered down.
Ville's extended explanation from the review thread:
On Wed, Aug 19, 2015 at 07:47:41AM +0530, Deepak wrote:
> One Q, why only for port B? Port C is also in same common lane right?
Port B is in the first PHY channel which also houses CL1. CL1 always
powers up whenever any lanes in either PHY channel are powered up.
CL2 only powers up if lanes in the second channel (ie. the one with
port C) powers up.
So in this scenario (pipe B->port B) we want the DPLL from CL2, but
ideally we only want to power up the lanes for port B. Powering up
port B lanes will only power up CL1, but as we need CL2 instead we
need to, temporarily, power up some lanes in port C as well.
Crossing the streams the other way (pipe A->port C) is not a problem
since CL1 powers up whenever anything else powers up. So powering up
some port C lanes is enough on its own to make the CL1 DPLL
operational, even though CL1 and the lanes live in separate channels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
[danvet: Amend commit message with extended explanation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.
Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.
With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.
Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.
A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.
We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.
Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.
v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
fallout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bunch of stuff needs the DPLL ref/cri clocks on both VLV and CHV,
and having VGA mode enabled causes some problems for CHV. So let's just
pull the code to configure those bits into the disp2d well enable hook.
With the DPLL disable code also fixed to leave those bits alone we
should now have a consistent DPLL state all the time even if the DPLL
is disabled.
This also neatly removes some duplicated code between the VLV and
CHV codepaths.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel
doesn't support MSI") changed the location of the code that initialises
dev->msi_cap/msix_cap and then disables MSI/MSI-X interrupts at PCI
probe time in devices that have this flag set. It moved the code from
pci_msi_init_pci_dev() to a new function named pci_msi_setup_pci_dev(),
called by pci_setup_device().
The pseries PCI probing code does not call pci_setup_device(), so since
the aforementioned commit the function pci_msi_setup_pci_dev() is not
called and MSI/MSI-X interrupts are left enabled. Additionally because
dev->msi_cap/msix_cap are not initialised no driver can ever enable
MSI/MSI-X.
To fix this, the pseries PCI probe should manually call
pci_msi_setup_pci_dev(), so this patch makes it non-static.
Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Update change log to mention dev->msi_cap/msix_cap]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes error handling in the function max732x_probe by checking
if the calls to the function max732x_readb fail by returning a error
code.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Below compilation warnings are observed in gcc version 4.8.2.
Even though it's not seen in bit older gcc versions (for ex, 4.7.3),
It's good to fix it by changing format specifier from %d to
%zd in wmi pull phyerr functions.
wmi.c: In function 'ath10k_wmi_op_pull_phyerr_ev':
wmi.c:3567:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
wmi.c: In function 'ath10k_wmi_10_4_op_pull_phyerr_ev':
wmi.c:3612:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
Fixes: 991adf71a6 ("ath10k: refactor phyerr event handlers")
Fixes: 2b0a2e0d7c ("ath10k: handle 10.4 firmware phyerr event")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simple one:
drivers/gpu/drm/i915/i915_debugfs.c:2449:57: warning: Using plain integer as NULL pointer
And something a bit more peculiar:
drivers/gpu/drm/i915/i915_debugfs.c:4953:18: warning: Variable length array is used.
drivers/gpu/drm/i915/i915_debugfs.c:4953:32: warning: Variable length array is used.
We pass a 'const int' as the array size which results in the warning,
dropping the const gets rid of the warning. Weird, but I think getting
rid of the warnings is better than holding on to the const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds additional 0x0041 PCI Device ID
definition to ath10k for QCA6164 which is a 1
spatial stream sibling of the QCA6174 (which is 2
spatial stream chip).
The QCA6164 needs a dedicated board.bin file which
is different than the one used for QCA6174. If the
board.bin is wrong the device will crash early
while trying to boot firmware. The register dump
will look like this:
ath10k_pci 0000:02:00.0: firmware register dump:
ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31
...
Note the value 0x000A012D.
Special credit goes to Alan Liu
<alanliu@qca.qualcomm.com> for providing support
help which enabled me to come up with this patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
BXT platform uses live status bits from 0x44440 register to obtain DP
status on hotplug. The existing g4x_digital_port_connected() uses a
different register and hence misses DP hotplug events on BXT
platform. This patch fixes it by using the appropriate register(0x44440)
and live status bits(3:5).
Based on a patch by Durgadoss R <durgadoss.r@intel.com>, from whom the
commit message is shamelessly copy pasted.
Reported-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a common intel_digital_port_connected() that splits out to functions
for different platforms. No functional changes.
v2: make the function return a boolean
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the case added for eDP on port A (always connected from this
function's point of view), we should not be hitting any of the default
cases in ibx_digital_port_connected, so add MISSING_CASE annotation.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should not be hitting any of the default cases in
g4x_digital_port_connected, so add MISSING_CASE annotation and return
boolean status. The current behaviour is just cargo culting from the
days of yonder when the display port support was added to i915.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
This patch applies to DVO.
V2:
- removed computation for max pixel clock
V3:
- cleanup by removing unnecessary lines
V4:
- clock check against max dotclock moved inside 'if (fixed_mode)'
V5:
- dot clock check against fixed_mode clock when available
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
This patch applies to DSI.
V2:
- removed computation for max pixel clock
V3:
- cleanup by removing unnecessary lines
V4:
- max_pixclk variable renamed as max_dotclk
- moved dot clock checking inside 'if (fixed_mode)'
V5:
- dot clock checked against fixed_mode clock
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is possible the we request to have a mode that has
higher pixel clock than our HW can support. This patch
checks if requested pixel clock is lower than the one
supported by the HW. The requested mode is discarded
if we cannot support the requested pixel clock.
This patch applies to LVDS.
V2:
- removed computation for max pixel clock
V3:
- cleanup by removing unnecessary lines
V4:
- moved supported dotclock check from mode_valid() to intel_lvds_init()
V5:
- dotclock check moved back to mode_valid() function
- dotclock check for fixed mode
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Store max dotclock into dev_priv structure so we are able
to filter out the modes that are not supported by our
platforms.
V2:
- limit the max dot clock frequency to max CD clock frequency
for the gen9 and above
- limit the max dot clock frequency to 90% of the max CD clock
frequency for the older gens
- for Cherryview the max dot clock frequency is limited to 95%
of the max CD clock frequency
- for gen2 and gen3 the max dot clock limit is set to 90% of the
2X max CD clock frequency
V3:
- max_dotclk variable renamed as max_dotclk_freq in i915_drv.h
- in intel_compute_max_dotclk() the rounding method changed from
round up to round down when computing max dotclock
V4:
- Haswell and Broadwell supports now dot clocks up to max CD clock
frequency
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With DPIO powergating active on CHV, we can't even access the DPIO PLL
registers until the lane power state overrides have been enabled. That
will happen from the encoder .pre_pll_enable() hook, so move
chv_prepare_pll() to happen after that point, which puts it just before
chv_enable_pll() actually.
Do the same for VLV to avoid accumulating weird differences between the
platforms. Both platforms seem happy with the new arrangement.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To implement DPIO lane power gating on CHV we're going to need to access
DPIO registers from the cmn power well enable hook. That gets called
rather early, so we need to move the DPIO port IOSF sideband port
assignment earlier as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the CHV clock buffer disable from chv_disable_pll() to the new
encoder .post_pll_disable() hook. This is more symmetric since the
clock buffer enable happens from the .pre_pll_enable() hook.
We'll have more use for the new hook soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs give you the impression that the unique transition scale
value shouldn't matter when unique transition scale is enabled. But
as Imre found on BXT (and I verfied also on BSW) the value does
matter. So from now on just program the same value 0x9a always.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When fractional m2 divider isn't used on CHV the fractional part
is ignore by the hardware. Despite that, program the fractional
value (0 in this case) to the hardware register just to keep
things a bit more consistent. Might at least make register dumps
a bit less confusing when there isn't some stale fractional part
hanging around.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To enable/configure spectral scan parameters in 10.4 firmware, existing
wmi spectral related functions can be reused. Link those functions in
10.4 wmi ops table.
In addition, adjust bin size (only when size is 68 bytes) before reporting
bin samples to user space. The background for this adjustment is that
qca99x0 reports bin size as 68 bytes (64 bytes + 4 bytes) in report
mode 2. First 64 bytes carries in-band tones (-32 to +31) and last 4 byte
carries band edge detection data (+32) mainly used in radar detection
purpose. Additional last 4 bytes are stripped to make bin size valid one.
This bin size adjustment will happen only for qca99x0, all other chipsets
will report proper bin sizes (64/128) without extra 4 bytes being added
at the end. The changes are validated in qca99x0 using 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function returns 1 when DMA mapping fails. The
driver would return bogus values and could
possibly confuse itself if DMA failed.
Fixes: 767d34fc67 ("ath10k: remove DMA mapping wrappers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kernel would complain about leaving a held lock
after going back to userspace and would
subsequently deadlock.
Fixes: e04cafbc38 ("ath10k: fix peer limit enforcement")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The current versions of these two macros don't work correctly if the
argument expression happens to contain a modulo operator (%) -- when
stringified, it gets interpreted as a printf formatting character!
With a specifically crafted parameter, this could probably cause a
kernel OOPS; consider WARN_ON(p%s) or WARN_ON(f %*pEp).
Instead, we should use an explicit "%s" format, with the stringified
expression as the coresponding literal-string argument.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With MST there won't be a crtc assigned to the main link encoder, so
trying to dig up the pipe_config from there is a recipe for an oops.
Instead store the parameters (lane_count and link_rate) in the encoder,
and use those values during link training etc. Since those parameters
are now assigned only when the link is actually enabled,
.compute_config() won't clobber them as it did before.
Hardware state readout is still bonkers though as we don't transfer the
link parameters from pipe_config intel_dp. We should do that during
encoder sanitation. But since we don't even do a proper job of reading
out the main link encoder state for MST there's littel point in
worrying about this now.
Fixes a regression with MST caused by:
commit 90a6b7b052
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Jul 6 16:39:15 2015 +0300
drm/i915: Move intel_dp->lane_count into pipe_config
v2: Different apporoach that should keep intel_dp_check_mst_status()
somewhat less oopsy
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per CCF documentation (clk.txt) the clk_prepare/unprepare APIs
are not allowed in atomic context. But now OMAP GPIO driver
uses them while applying debounce settings and as part
of PM runtime irqsafe operations:
- omap_gpio_debounce() is holding the lock with IRQs off.
+ omap2_set_gpio_debounce()
+ clk_prepare_enable()
+ clk_prepare() this one might sleep.
- pm_runtime_get_sync() is holding the lock with IRQs off
+ omap_gpio_runtime_suspend()
+ raw_spin_lock_irqsave()
+ omap_gpio_dbck_disable()
+ clk_disable_unprepare()
Hence, fix it by moeving dbclk prepare/unprepare in OMAP GPIO
omap_gpio_probe/omap_gpio_remove. Also, while here, ensure that
debounce functionality is disabled if clk_get() failed,
because otherwise kernel will carsh in omap2_set_gpio_debounce().
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The access to HW registers has to be be protected in
omap_gpio_irq_handler(), as it may race with code executed on
another CPUs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to TRMs:
Required input line stable =
(the value of the GPIO_DEBOUNCINGTIME[7:0].DEBOUNCETIME + 1) × 31,
where the value of the GPIO_DEBOUNCINGTIME[7:0].DEBOUNCETIME bit field
is from 0 to 255.
But now omap2_set_gpio_debounce() will calculate debounce time and
behave incorrectly in the following cases:
1) requested debounce time is !0 and <32
calculated DEBOUNCETIME = 0x1 == 62 us;
expected value of DEBOUNCETIME = 0x0 == 31us
2) requested debounce time is 0
calculated DEBOUNCETIME = 0x1 == 62 us;
expected: disable debounce and DEBOUNCETIME = 0x0
3) requested debounce time is >32 and <63
calculated DEBOUNCETIME = 0x0 and debounce will be disabled;
expected: enable debounce and DEBOUNCETIME = 0x1 == 62 us
Hence, rework omap2_set_gpio_debounce() to fix above cases:
1) introduce local variable "enable" and use it to identify
when debounce need to be enabled or disabled. Disable debounce
if requested debounce time is 0.
2) use below formula for debounce time calculation:
debounce = (DIV_ROUND_UP(debounce, 31) - 1) & 0xFF;
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switch OMAP GPIO driver to use platform_get_irq(), because
it is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ, ..)
for requesting IRQ resources any more, as they can be not ready yet
in case of DT-boot.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to a coherency issue on BXT A steppings we can't guarantee a
coherent view of cached (CPU snooped) GPU mappings, so fail such
requests. User space is supposed to fall back to uncached mappings in
this case.
v2:
- limit the WA to A steppings, on later stepping this HW issue is fixed
v3:
- return error instead of trying to work around the issue in kernel,
since that could confuse user space (Chris)
Testcast: igt/gem_store_dword_batches_loop/cached-mapping
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By running igt/store_dword_loop_render on BXT we can hit a coherency
problem where the seqno written at GPU command completion time is not
seen by the CPU. This results in __i915_wait_request seeing the stale
seqno and not completing the request (not considering the lost
interrupt/GPU reset mechanism). I also verified that this isn't a case
of a lost interrupt, or that the command didn't complete somehow: when
the coherency issue occured I read the seqno via an uncached GTT mapping
too. While the cached version of the seqno still showed the stale value
the one read via the uncached mapping was the correct one.
Work around this issue by clflushing the corresponding CPU cacheline
following any store of the seqno and preceding any reading of it. When
reading it do this only when the caller expects a coherent view.
v2:
- fix using the proper logical && instead of a bitwise & (Jani, Mika)
- limit the workaround to A stepping, on later steppings this HW issue
is fixed
v3:
- use a separate get_seqno/set_seqno vfunc (Chris)
Testcase: igt/store_dword_loop_render
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The at91-specific irq_{request,release}_resources() callbacks are
identical to the generic ones, modulo the bug fix in 5b76e79c77
("gpiolib: irqchip: prevent driver unloading if gpio is used as irq
only").
Until commit 8b67a1f0ad ("gpio: don't override irq_*_resources()
callbacks"), the buggy at91-specific callbacks were never used, though.
Hence drop the at91-specific ones in favor of the generic ones.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When running -rt kernel and an interrupt happens on a GPIO line controlled by
Intel Cherryview/Braswell pinctrl driver we get:
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/0
Preemption disabled at:[<ffffffff81092e9f>] cpu_startup_entry+0x17f/0x480
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.1.5-rt5 #16
...
Call Trace:
<IRQ> [<ffffffff816283c6>] dump_stack+0x4a/0x61
[<ffffffff81077e17>] ___might_sleep+0xe7/0x170
[<ffffffff8162d6cf>] rt_spin_lock+0x1f/0x50
[<ffffffff812e52ed>] chv_gpio_irq_ack+0x3d/0xa0
[<ffffffff810a72f5>] handle_edge_irq+0x75/0x180
[<ffffffff810a3457>] generic_handle_irq+0x27/0x40
[<ffffffff812e57de>] chv_gpio_irq_handler+0x7e/0x110
[<ffffffff810050aa>] handle_irq+0xaa/0x190
...
This is because desc->lock is raw_spinlock and is held when chv_gpio_irq_ack()
is called by the genirq core. chv_gpio_irq_ack() in turn takes pctrl->lock
which in -rt is an rt-mutex causing might_sleep() rightfully to complain about
sleeping function called from invalid context.
In order to keep -rt happy but at the same time make sure that register
accesses get serialized, convert the driver to use raw_spinlock instead.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel Baytrail pinctrl driver implements irqchip callbacks which are
called with desc->lock raw_spinlock held. In mainline this is fine because
spinlock resolves to raw_spinlock. However, running the same code in -rt we
get:
BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:917
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/0
Preemption disabled at:[<ffffffff81092e9f>] cpu_startup_entry+0x17f/0x480
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.1.5-rt5 #13
...
Call Trace:
<IRQ> [<ffffffff816283c6>] dump_stack+0x4a/0x61
[<ffffffff81077e17>] ___might_sleep+0xe7/0x170
[<ffffffff8162d6cf>] rt_spin_lock+0x1f/0x50
[<ffffffff812e3b88>] byt_gpio_clear_triggering+0x38/0x60
[<ffffffff812e3bc1>] byt_irq_mask+0x11/0x20
[<ffffffff810a7013>] handle_level_irq+0x83/0x150
[<ffffffff810a3457>] generic_handle_irq+0x27/0x40
[<ffffffff812e3a5f>] byt_gpio_irq_handler+0x7f/0xc0
[<ffffffff810050aa>] handle_irq+0xaa/0x190
...
This is because in -rt spinlocks are preemptible so taking the driver
private spinlock in irqchip callbacks causes might_sleep() to trigger.
In order to keep -rt happy but at the same time make sure that register
accesses get serialized, convert the driver to use raw_spinlock instead.
Also shorten the critical section a bit in few places.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
v2: fix one error found by checkpath.pl
v3: Add one ignored break for switch-case. DDI-E hotplug
function doesn't work after updating drm-intel tree,
I checked the code and found this missing which isn't
the root cause for broke DDI-E hp. The broken
DDI-E hp function is fixed by "Adding DDI_E power
well domain".
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Timo Aaltonen <timo.aaltonen@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Since Surface Pro 3 does not follow the specs of "Windows ACPI Design
Guide for SoC Platform", code in drivers/input/misc/soc_array.c can
not detect these buttons on it. According to bios implementation,
Surface Pro 3 encapsulates these buttons in a device named "VGBI",
with _HID "MSHW0028". When any of the buttons is pressed, a specify
ACPI notification code for this button will be delivered to "VGBI". For
example, if power button is pressed down, ACPI notification code of 0xc6
will be sent by Notify(VGBI, 0xc6).
This patch leverages "VGBI" to distinguish different ACPI notification
code from Power button, Home button, Volume button, then dispatches these
code to input layer. Lid is already covered by acpi button driver, so
there's no need to rewrite.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=84651
Tested-by: Ethan Schoonover <es@ethanschoonover.com>
Tested-by: Peter Amidon <psa.pub.0@picnicpark.org>
Tested-by: Donavan Lance <tusklahoma@gmail.com>
Tested-by: Stephen Just <stephenjust@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
[dvhart@linux.intel.com: Formatting corrections in MAINTAINERS and Intel (c)]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The gtt.stolen_size field is of type size_t, and so should be printed
using %zu to avoid build warnings on either 32-bit and 64-bit builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
SKL-Y can now use the same programming for all VccIO values after an
adjustment to I_boost. SKL-U DP table adjustments.
1. Remove SKL Y 0.95V from "SKL H and S" columns in all tables. The
other SKL Y column removes the "0.85V VccIO" so it now applies to all
voltages.
2. DP table changes SKL U 400mV+0db dword 0 value from 2016h to 201Bh.
3. DP table changes SKL U 600mv+0db dword 0 value from 2016h to 201Bh.
4. DP table increases I_boost to level 3 for SKL Y 400mv+9.5db.
v2: Fix compilation warnings as pointed by Paulo.
Reference: Graphics Spec Change r97962
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[Jani: reformatted commit message for shorter lines.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
