Enabling irq wake could potentially fail and calling disable_irq_wake
after a failed call to enable_irq_wake could result in an unbalanced irq
warning. This patch warns if enable_irq_wake fails and avoids other
potential issues caused by calling disable_irq_wake on resume after
enable_irq_wake failed during suspend.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The current generation of "Intuos" tablets (i.e. INTUOSHT) report touch
width and height data just like the "Intuos Pro" do. This commit changes
the code to allow these tablets to use the appropriate codepath instead
of the one intended for Intuos5/Bamboo.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This gamepad advertise 5 absolute axis while 4 are actually used.
The second Z axis shows some garbage, so it has to be ignored by HID.
The first Z axis and the Rz one are actually Rx and Ry. Remap them.
We could also just remap and ignore the axis in .input_mapping(). I
went ahead with .report_fixup() first, so here it is.
Reported-by: Orivej Desh <orivej@gmx.fr>
Tested-by: Orivej Desh <orivej@gmx.fr>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I2CM_ADDRESS became a MESS, fix it, also change guarding define
to __DW_HDMI_H__ , since the driver is not IMX specific.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dw_hdmi enable/disable handling is particularly weak in several
regards:
* The hotplug interrupt could call hdmi_poweron() or hdmi_poweroff()
while DRM is setting a mode, which could race with a mode being set.
* Hotplug will always re-enable the phy whenever it detects an active
hotplug signal, even if DRM has disabled the output.
Resolve all of these by introducing a mutex to prevent races, and a
state-tracking bool so we know whether DRM wishes the output to be
enabled. We choose to use our own mutex rather than ->struct_mutex
so that we can still process interrupts in a timely fashion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi_phy_enable_power() is not about enabling and disabling power.
It is about allowing or preventing power-down mode being entered - the
register is documented as "Power-down enable (active low 0b)."
This can be seen as the bit has no effect when the HDMI phy is
operational on iMX6 hardware.
Rename the function to dw_hdmi_phy_enable_powerdown() to reflect the
documentation, make it take a bool for the 'enable' argument, and invert
the value to be written.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On a mode set, DRM makes the following sequence of calls:
* for_each_encoder
* bridge mode_fixup
* encoder mode_fixup
* crtc mode_fixup
* for_each_encoder
* bridge disable
* encoder prepare
* bridge post_disable
* disable unused encoders
* crtc prepare
* crtc mode_set
* for_each_encoder
* encoder mode_set
* bridge mode_set
* crtc commit
* for_each_encoder
* bridge pre_enable
* encoder commit
* bridge enable
dw_hdmi enables the HDMI output in both the bridge mode_set() and also
the bridge enable() step. This is duplicated work - we can avoid the
setup in mode_set() and just do it in the enable() stage. This
simplifies the code a little.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only enable audio support if the sink supports audio in some form, as
defined via its EDID. We discover this capability using the generic
drm_detect_monitor_audio() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The FSL kernel detects the HDMI vendor id, and uses this to set
hdmi->edid_cfg.hdmi_cap, which is then used to set mdvi appropriately,
rather than detecting whether we are outputting a CEA mode. Update
the dw_hdmi code to use this logic, but lets eliminate the mdvi
variable, prefering the more verbose "hdmi->sink_is_hdmi" instead.
Use the generic drm_detect_hdmi_monitor() to detect a HDMI sink.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As mentioned in the previous commit, the dw-hdmi driver does not support
pixel doubled modes at present; it does not configure the PLL correctly
for these modes. Therefore, filter out the double-clocked modes as we
presently are unable to support them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi sets a pixel repetition factor of 1 for VICs 10-15, 25-30 and
35-38. However, DRM uses their native resolutions in its timing
information. For example, VIC 14 can be 1440x480 with no repetition,
or 720x480 with one pixel repetition. As DRM uses 1440 pixels per line
for this video mode, we need no pixel repetition.
In any case, pixel repetition appears broken in dw_hdmi.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the struct hdmi_vmode mhsyncpolarity/mvsyncpolarity/minterlaced
members, which are only used within a single function. We can directly
reference the appropriate mode->flags instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a YCBCR format is selected, we can merely copy the colorimetry
information directly as we use the same definitions for both the
unpacked AVI info frame and the hdmi_data_info structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up hdmi_set_clk_regenerator() by allowing it to take the audio
sample rate and ratio directly, rather than hiding it inside the
function. Raise the unsupported pixel clock/sample rate message from
debug to error level as this results in audio not working correctly.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy configuration is dependent on the SoC, and we look up values for
some of the registers in SoC specific data. However, we had partially
programmed the phy before we had successfully looked up the clock rate.
Also, we were only checking that we had a valid configuration for the
currctrl register.
Move all these lookups to the start of this function instead, so we can
check that all lookups were successful before beginning to program the
phy.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
userspace programs using cxl currently have to use two strategies for
dealing with MMIO errors simultaneously. They have to check every read
for a return of all Fs in case the adapter has gone away and the kernel
has not yet noticed, and they have to deal with SIGBUS in case the
kernel has already noticed, invalidated the mapping and marked the
context as failed.
In order to simplify things, this patch adds an alternative approach
where the kernel will return a page filled with Fs instead of delivering
a SIGBUS. This allows userspace to only need to deal with one of these
two error paths, and is intended for use in libraries that use cxl
transparently and may not be able to safely install a signal handler.
This approach will only work if certain constraints are met. Namely, if
the application is both reading and writing to an address in the problem
state area it cannot assume that a non-FF read is OK, as it may just be
reading out a value it has previously written. Further - since only one
page is used per context a write to a given offset would be visible when
reading the same offset from a different page in the mapping (this only
applies within a single context, not between contexts).
An application could deal with this by e.g. making sure it also reads
from a read-only offset after any reads to a read/write offset.
Due to these constraints, this functionality must be explicitly
requested by userspace when starting the context by passing in the
CXL_START_WORK_ERR_FF flag.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
'0f1fb99 iommu/fsl: Fix section mismatch' was intended to address the modpost
warning and the potential crash. Crash which is actually easy to trigger with a
'unbind' followed by a 'bind' sequence. The fix is wrong as
fsl_of_pamu_driver.driver gets added by bus_add_driver() to a couple of
klist(s) which become invalid/corrupted as soon as the init sections are freed.
Depending on when/how the init sections storage is reused various/random errors
and crashes will happen
'cd70d46 iommu/fsl: Various cleanups' contains annotations that go further down
the wrong path laid by '0f1fb99 iommu/fsl: Fix section mismatch'
Now remove all the incorrect annotations from the above mentioned patches (not
exactly a revert) and those previously existing in the code, This fixes the
modpost warning(s), the unbind/bind sequence crashes and the random
errors/crashes
Fixes: 0f1fb99b62 ("iommu/fsl: Fix section mismatch")
Fixes: cd70d4659f ("iommu/fsl: Various cleanups")
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Acked-by: Varun Sethi <Varun.Sethi@freescale.com>
Cc: stable@vger.kernel.org
Tested-by: Madalin Bucur <Madalin.Bucur@freescale.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
When installing a block mapping, we unconditionally overwrite a non-leaf
PTE if we find one. However, this can cause a problem if the following
sequence of events occur:
(1) iommu_map called for a 4k (i.e. PAGE_SIZE) mapping at some address
- We initialise the page table all the way down to a leaf entry
- No TLB maintenance is required, because we're going from invalid
to valid.
(2) iommu_unmap is called on the mapping installed in (1)
- We walk the page table to the final (leaf) entry and zero it
- We only changed a valid leaf entry, so we invalidate leaf-only
(3) iommu_map is called on the same address as (1), but this time for
a 2MB (i.e. BLOCK_SIZE) mapping)
- We walk the page table down to the penultimate level, where we
find a table entry
- We overwrite the table entry with a block mapping and return
without any TLB maintenance and without freeing the memory used
by the now-orphaned table.
This last step can lead to a walk-cache caching the overwritten table
entry, causing unexpected faults when the new mapping is accessed by a
device. One way to fix this would be to collapse the page table when
freeing the last page at a given level, but this would require expensive
iteration on every map call. Instead, this patch detects the case when
we are overwriting a table entry and explicitly unmaps the table first,
which takes care of both freeing and TLB invalidation.
Cc: <stable@vger.kernel.org>
Reported-by: Brian Starkey <brian.starkey@arm.com>
Tested-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Describe capabilities of the HLCDC IP found on sama5d4 SoCs and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Describe capabilities of the HLCDC IP found on at91sam9n12 SoC and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Describe capabilities of the HLCDC IP found on at91sam9x5 SoCs and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The atmel-hlcdc driver already supports atomic operations, add the
missing DRM_ATOMIC flag to expose the atomic features to userspace.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When we enter D0i3, we must stop TXing otherwise the
sequence number we use might conflict with the firmware's
internal TX. In order to do so, we have
IWL_MVM_STATUS_IN_D0I3 which should prevent any Tx while we
enter D0i3. There is a bug in this code since we may Tx even
if IWL_MVM_STATUS_IN_D0I3 is set. This can happen as long as
mvm->d0i3_ap_sta_id is not set.
To make sure that we don't have any packet in the Tx path
while we set mvm->d0i3_ap_sta_id, call synchronize_net only
after we already set mvm->d0i3_ap_sta_id.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently if we wake up during D0I3 due to beacon loss we disconnect
immediately. This behaviour causes redundant disconnection, which could
be prevented by polling as it is usually done in mac80211.
Instead, we prefer reporting beacon loss and let mac80211 try polling
before disconnection.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
KASan error report:
==================================================================
BUG: KASan: out of bounds access in iwl_init_sband_channels+0x207/0x260 [iwlwifi] at addr ffff8800c2d0aac8
Read of size 4 by task modprobe/329
==================================================================
Both loops of this function compare data from the 'chan' array and then
check if the index is valid.
The 2 conditions should be inverted to avoid an out-of-bounds access.
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix bug where MIMO is disabled for low latency TX on P2P VIF
regardless of configuration. Make it dependent on
IWL_MVM_RS_DISABLE_P2P_MIMO compilation option. Change configuration
so that MIMO will be disabled only in SDIO platforms.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This switches the BCMA GPIO driver to use GPIOLIB_IRQCHIP to
handle its interrupts instead of rolling its own copy of the
irqdomain handling etc.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add diversity statistics and sync the driver
statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync the driver statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2500usb_validate_eeprom() read data up to 0x6e (EEPROM_CALIBRATE_OFFSET)
but only 0x6a bytes has been allocated and read from the eeprom.
This lead to out-of-bound accesses and invalid values for
EEPROM_BBPTUNE_R17 and EEPROM_CALIBRATE_OFFSET.
Change the EEPROM_SIZE to 0x6e in order to retrieve all the fields.
Tested with a rt2570 device.
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CC [M] drivers/net/wireless/mwl8k.o
drivers/net/wireless/mwl8k.c: In function ‘mwl8k_bss_info_changed’:
drivers/net/wireless/mwl8k.c:3290:2: warning: ‘ap_mcs_rates’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(cmd->mcs_set, mcs_rates, 16);
^
drivers/net/wireless/mwl8k.c:4987:5: note: ‘ap_mcs_rates’ was declared here
u8 ap_mcs_rates[16];
^
The warning was bogus. But the conditionals were rather complicated,
with multiple redundant checks. This consolidates the checking and
makes it more readable IMHO.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I remove duplicated routines which related rtl92cu_set_hw_reg().
1. rtl92c_set_qos() and HW_VAR_AC_PARAM routine are similar code.
so i replace code with rtlpriv->cfg->ops->set_hw_reg().
2. rtl92c_set_mac_addr() and 'HW_VAR_ETHER_ADDR' case at
rtl92cu_set_hw_reg() routine are similar code.
so i removed rtl92c_set_mac_addr() function.
also it was not used anywhere.
3. remove HW_VAR_ACM_CTRL routine in rtl92cu_set_hw_reg().
if rtl_usb->acm_method is not EACMWAY2_SW, HW_VAR_ACM_CTRL is called
from HW_VAR_AC_PARAM. but it never called. because acm_method is always
EACMWAY2_SW. so i remove acm_method check routine
and HW_VAR_ACM_CTRL routine.
both usb and pci interface is not used HW_VAR_ACM_CTRL.
but i can't test pci interface module, so i didn't modify pci code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl92c_set_xxx_filter is same routine with rtl92cu_set_hw_reg.
so i remove those functions that are rtl92c_set_xxx_filter.
(rtl92c_get_xxx_filter is also same reason.)
also i add code updating struct rtl_mac member variable in the
rtl92cu_set_hw_reg.
after that, no more _update_mac_setting is not useful. thus i remove that.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
>> drivers/net/ethernet/cisco/enic/vnic_dev.c:1095:13: sparse: incorrect type in assignment (different address spaces)
drivers/net/ethernet/cisco/enic/vnic_dev.c:1095:13: expected void *res
drivers/net/ethernet/cisco/enic/vnic_dev.c:1095:13: got void [noderef] <asn:2>*
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>> drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:173:44: sparse: incorrect type in argument 1 (different base types)
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:173:44: expected restricted __sum16 [usertype] n
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:173:44: got restricted __be16 [usertype] check_sum
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LS1021A is a QorIQ SoC having little endian CAAM.
There are a few differences b/w QorIQ and i.MX from CAAM perspective:
1. i.MX platforms are somewhat special wrt. 64-bit registers:
-big endian format at 64-bit level: MSW at address+0 and LSW at address+4
-little endian format at 32-bit level (within MSW and LSW)
and thus need special handling.
2. No CCM (clock controller module) for QorIQ.
No CAAM clocks to enable / disable.
A new Kconfig option - CRYPTO_DEV_FSL_CAAM_LE - is added to indicate
CAAM is little endian (*). It is hidden from the user (to avoid
misconfiguration); when adding support for a new platform with LE CAAM,
either the Kconfig needs to be updated or the corresponding defconfig
needs to indicate that CAAM is LE.
(*) Using a DT property to provide CAAM endianness would not allow
for the ifdeffery.
In order to keep changes to a minimum, the following changes
are postponed:
-endianness fix of the last word in the S/G (rsvd2, bpid, offset),
fields are always 0 anyway;
-S/G format fix for i.MX7 (yes, i.MX7 support was not added yet,
but still...)
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
