This change is to add properties alpha/zpos/blend_mode to mdp5 plane
for alpha blending operation to generate the blended output.
v1: Initial change
v2: Change "premultilied" property to enum (Rob's comment)
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
[Don't actually expose alpha/premultiplied props to userspace yet
pending a chance for discussion and some userspace to exercise it]
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was a hold-over from the pre-atomic days and legacy userspace that
only understood CRTCs. Fortunately we don't have any properties, so
this doesn't change anything. But before we start growing some plane
properties, we should fix this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY errors are falsely reported whenever a dsi error occurs. This is
because DSI_DLN0_PHY_ERR isn't only used as a status register, but also
used to mask PHY errors. Currently, we end up reading the mask bits too
and therefore always report errors.
Ignore the register mask bits and check for only the status/clear bits.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The maximum output width of one pipeline depends on the LayerMixer's
capability. It may be different on each target. Also, MDP5 doesn't
have vertical limitation in one frame, as long as the pixel clock
can be supported.
This change obtains the maximum LM resolution from configuration
table and treat it as the whole pipe's limitation for MDP5. The size
limit on MDP4 is not changed.
Signed-off-by: Hai Li <hali@codeaurora.org>
For all of these devices, msm89xy was the lead chip, so standardize the
compatible names to align with convention used by rest of the qcom/msm
drivers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the MDP and HDMI support for msm8x94.
Note that HDMI PHY registers are not being accessed anymore from
the driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[rename compatible s/8x94/8994/ since preference is to not trust the
marketing folks who invent chip #'s but instead name things after the
lead chip.. we should rename some 80XY to 89XY to standardize on the
lead chip but leave that for another patch. Also, update dt bindings
doc]
Signed-off-by: Rob Clark <robdclark@gmail.com>
->reset() currently only accesses HDMI core registers, and yet it
is located in hdmi_phy*. Since no PHY registers are being
accessed during ->reset(), it would be better to bring that
function in hdmi core module where HDMI core registers are
usually being accessed.
This will also help for msm8x94 for which no PHY registers
accesses are done (->phy_init == NULL) but the HDMI PHY reset
from HDMI core still needs to be done.
Note:
SW_RESET_PLL bit is not written in hdmi_phy_8x60_reset(); this
write should not affect anything if the corresponding field is
not writable.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[fixed warning about unused 'phy' in hpd_enable() while merging]
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI controller on msm8x94 is version 1.3, which requires different
power supplies and works with 20nm DSI PHY. This change is to add
the basic support for this version.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some targets use pinctrl framework to configure some
pins. This change allows DSI driver to set default and
sleep pinctrl status.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current term of *dual panel* in DSI driver code causes confusion.
It is supposed to indicate the panel using two DSI links. Rename it
to *dual DSI*.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The source PLL to be used by each DSI PHY should be decided by
DSI manager based on dual DSI information, while the register
programming to select PLL is different from one type of PHY to
another. This change adds the H/W difference to PHY configuration
and updates the interface between DSI manager and PHY.
With this change, PLL selection can be supported on different
targets.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add HDMI HDCP support including HDCP PartI/II/III authentication.
V1: Initial Change
V2: Address Bjorn&Rob's comments
Refactor the authentication process to use single work instead
of multiple work for different authentication stages.
V3: Update to align with qcom SCM api.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pull SCSI fixes from James Bottomley:
"This has two libfc fixes for bugs causing rare crashes, one iscsi fix
for a potential hang on shutdown, and a fix for an I/O blocksize issue
which caused a regression"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sd: Fix maximum I/O size for BLOCK_PC requests
libfc: Fix fc_fcp_cleanup_each_cmd()
libfc: Fix fc_exch_recv_req() error path
libiscsi: Fix host busy blocking during connection teardown
single MST fixes from Maarten.
* tag 'topic/drm-fixes-2015-08-14' of git://anongit.freedesktop.org/drm-intel:
drm/dp/mst: Remove port after removing connector.
three display fixes for Intel.
* tag 'drm-intel-fixes-2015-08-14' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Commit planes on each crtc separately.
drm/i915: calculate primary visibility changes instead of calling from set_config
drm/i915: Only dither on 6bpc panels
Replace with struct vnt_tx_desc with all members the same.
volatile is removed from pointers as this generates warning
message.
Only the first four members of vnt_tx_desc need to be volatile.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create struct vnt_td_info with members
mic_hdr
skb
buf
buf_dma
dwReqCount -> req_count
byFlags -> flags
In struct tagSTxDesc volatile is removed because it will generate a warning
(in any case this member is not) and renaming td_info.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwHeaderLength is assigned a value but that is never used.
Remove variable.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix "foo* bar" should be "foo *bar" errors as detected by
checkpatch.pl
Signed-off-by: Yash Shah <yshah1@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dm_odm was being checked for NULL after dereferencing it. Lets check for
NULL first before derefenrencing it.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the void pointer type in the host interface
functions which process the message from host thread by the real data
type, tstrWILC_WFIDrv because the void pointer type as the arguments
is not clear and concise. In addition, typecasting to the void pointer
type is removed becasue it is not necessary.
Signed-off-by: Johnny Kim <johnny.kim@atmel.com>
Signed-off-by: Tony Cho <tony.cho@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the void pointer member of the tstrHostIFmsg to the
real data type because the void pointer type is ambiguous and not
readable.
Signed-off-by: Johnny Kim <johnny.kim@atmel.com>
Signed-off-by: Tony Cho <tony.cho@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The structure, WILC_WFIDrvHandle is used to save the pointer address
for the driver handler which is used throughout the driver but it's
not easy to understand what it means. In addition, it doesn't support
the 64 bit machine and also causes the warnings for the 64 bit build.
This patch replaces the WILC_WFIDrvHandle by the tstrWILC_WFIDrv
because the tstrWILC_WFIDrv is real structure to represent the driver
handler and reduces the 64 bit compile warnings. Also, typecasting to
WILC_WFIDrvHandle is not needed by using tstrWILC_WFIDrv as is.
Signed-off-by: Johnny Kim <johnny.kim@atmel.com>
Signed-off-by: Tony Cho <tony.cho@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove unused memory functions because some macros with this
memory function are deleted.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to the vme_pio2_core.c that adds spaces around '-'.
Signed-off-by: Junsu Shin <jjunes0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to vme_pio2_core.c that fixes up the NULL comparison style.
Signed-off-by: Junsu Shin <jjunes0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to the vme_pio2_core.c that removes blank line after open brace '{'.
Signed-off-by: Junsu Shin <jjunes0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to vm2_pio2_core.c that removes multiple blanks lines.
Signed-off-by: Junsu Shin <jjunes0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
visorbus_dev_groups is not referenced outside visorbus_main.c, so it can
be declared static.
Found using sparse.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an module alias and a MODULE_DEVICE_TABLE to autoload the
visornic driver when an appropriate device is created by the visorbus.
Note, the correct way of fixing this is adding functionality to
scripts/mod/file2alias.c for the visorbus bus type.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Benjamin Romer <benjamin.romer@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
