The 'wacom_wireless_work' function does not recalculate the tablet's
resolution, causing the value contained in the 'features' struct to
always be reported to userspace. This value is valid only for the pen
interface, meaning that the value will be incorrect for the touchpad (if
present). This in particular causes problems for libinput which relies
on the reported resolution being correct.
This patch adds the necessary calls to recalculate the resolution for
each interface. This requires a little bit of code shuffling since both
the 'wacom_set_default_phy' and 'wacom_calculate_res' are declared below
their new first point of use in 'wacom_wireless_work'.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It's a good idea, and it brings us in line with the rest of arch/powerpc.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Writing each 4Kb page into flash might take up-to ~100 miliseconds,
during which time management firmware cannot acces the nvram for its
own uses.
Firmware upgrade utility use the ethtool API to burn new flash images
for the device via the ethtool API, doing so by writing several page-worth
of data on each command. Such action might create problems for the
management firmware, as the nvram might not be accessible for a long time.
This patch changes the write implementation, releasing the nvram lock on
the completion of each page, allowing the management firmware time to
claim it and perform its own required actions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change isdn driver, remove reverse_bits() function,
use the generic revbit8() function instead.
Signed-off-by: yalin wang <yalin.wang2010@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were missing curly braces so it means we call add_debugfs_mem()
unintentionally.
Fixes: 3ccc6cf74d ('cxgb4: Adds support for T6 adapter')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allocates a large chunk of temporary buffer using kzalloc
to copy FW image. As there is no real need of this memory to be
physically contiguous, use vzalloc instead.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases it is required to capture minidump for iSCSI functions
as part of default minidump collection process. To enable this, firmware
exports it's capability and driver need to enable that capability
by issuing a mailbox command.
With this feature, firmware can provide additional iSCSI function's
minidump with smaller minidump capture mask (0x1f).
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the Marvel 88e1111 PHY only two SGMII modes are available, both
allowing only SGMII to copper mode (with or without clock). SGMII
to fiber mode is not supported. Make sure the fiber/copper registers
selector bits are cleared for selecting copper mode.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
cpu 0 cpu 1
fec_enet_txq_submit_skb
reserve a bdp for the first fragment
fec_enet_txq_submit_frag_skb
update the bdp for the other fragment
update txq->cur_tx
fec_enet_tx_queue
bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
This bdp is the bdp reserved for the first segment. Given
that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
is already pointed to a bdp beyond this one. We think this is a
completed bdp and try to reclaim it.
update the bdp for the first segment
update txq->cur_tx
So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We queued interrupt events for the MRL being opened or closed, but the code
in interrupt_event_handler() that handles these events ignored them.
Stop enabling MRL interrupts and remove the ignored events.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The list of interrupt events (INT_BUTTON_IGNORE, INT_PRESENCE_ON, etc.) was
copied from other hotplug drivers, but pciehp doesn't use them all.
Remove the interrupt events that aren't used by pciehp.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's platform-dependent, but an MMIO read to a non-existent PCI device
generally returns data with all bits set. This happens when the host
bridge or Root Complex times out waiting for a response from the device and
fabricates return data to complete the CPU's read.
One example, reported in the bugzilla below, involved this hierarchy:
pci 0000:00:1c.0: PCI bridge to [bus 02-3a] Root Port
pci 0000:02:00.0: PCI bridge to [bus 03-0a] Upstream Port
pci 0000:03:03.0: PCI bridge to [bus 05-07] Downstream Port
pci 0000:05:00.0: PCI bridge to [bus 06-07] Thunderbolt Upstream Port
pci 0000:06:00.0: PCI bridge to [bus 07] Thunderbolt Downstream Port
pci 0000:07:00.0: BCM57762 NIC
Unplugging the Thunderbolt switch and the NIC below it resulted in this:
pciehp 0000:03:03.0: Surprise Removal
tg3 0000:07:00.0: tg3_abort_hw timed out, TX_MODE_ENABLE will not clear MAC_TX_MODE=ffffffff
pciehp 0000:06:00.0: unloading service driver pciehp
pciehp 0000:06:00.0: pcie_isr: intr_loc 11f
pciehp 0000:06:00.0: Switch interrupt received
pciehp 0000:06:00.0: Latch open on Slot
pciehp 0000:06:00.0: Attention button interrupt received
pciehp 0000:06:00.0: Button pressed on Slot
pciehp 0000:06:00.0: Presence/Notify input change
pciehp 0000:06:00.0: Card present on Slot
pciehp 0000:06:00.0: Power fault interrupt received
pciehp 0000:06:00.0: Data Link Layer State change
pciehp 0000:06:00.0: Link Up event
The pciehp driver correctly noticed that the Thunderbolt switch (05:00.0
and 06:00.0) and NIC (07:00.0) had been removed, and it called their driver
remove methods.
Since the NIC was already gone, tg3 received 0xffffffff when it tried to
read from the device. The resulting timeout is a tg3 issue and not of
interest here.
Similarly, since the 06:00.0 Thunderbolt switch was already gone,
pcie_isr() received 0xffff when it tried to read PCI_EXP_SLTSTA, and pciehp
thought that was valid status showing that many events had happened: the
latch had been opened, the attention button had been pressed, a card was
now present, and the link was now up. These are all wrong, of course, but
pciehp went on to try to power up and enumerate devices below the
non-existent bridge:
pciehp 0000:06:00.0: PCI slot - powering on due to button press
pciehp 0000:06:00.0: Surprise Insertion
pci 0000:07:00.0 id reading try 50 times with interval 20 ms to get ffffffff
[bhelgaas: changelog, also check in pcie_poll_cmd() & pcie_do_write_cmd()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99841
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
bus->host_pdev is part of a union so bus->host_pdev != NULL is probably
also true for PCIe devices, because there it accesses bus->host_pci. If
we access the dev member at the offset defined in struct
platform_device in struct pci_dev instead we probably get something
else.
This patch adds a new function which returns the host dev struct and
NULL if we do not have a host dev. When this gets registered on MIPS
brcm47xx we do not have a host dev in some situations.
This function could also be used in other places.
This problem was introduced in this commit:
commit cae761b5a6
Author: Rafa? Mi?ecki <zajec5@gmail.com>
Date: Sun Jun 28 17:17:13 2015 +0200
bcma: populate bus DT subnodes as platform_device-s
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Add a spinlock which will ensure that.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Since rx path is run in driver tasklet,
tx status cannot be reported directly from interrupt context
(there would be no way to lock it out).
Add tasklet for tx and move all possible code from irq handler
there.
Note: tx tasklet is needed because workqueue is queued very
rarely and that kills TCP performance.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx is run inside a tasklet so ieee80211_rx() should be used
instead of ieee80211_rx_ni().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DMA to variables located on the stack is a bad idea.
For simplicity and to avoid frequent allocations create
a buffer inside the device structure. Protect this
buffer with vendor_req_mutex. Don't protect vendor
requests which don't use this buffer.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When starting a p2p mgmt interface, enable its device role. This
allows us to keep the sta role disabled and scan on the dev role.
In general, p2p management interfaces cannot send vif-specific commands
to FW, as the vif role id is invalid. Only off-channel data and scans
happen on this vif, so most ops are not relevant.
If the vif is a p2p mgmt vif, block some mac80211 ops.
Configure rate policies for p2p mgmt interface, as
otherwise p2p packets come out with arbitrary rates.
Since wpa_supplicant currently doesn't support standalone
p2p device mode (without another attached managed interface),
add p2p device to the allowed interface combinations without
decreasing the allowed station count.
Moreover, increase the station count in some cases, as AP
mode usually starts as station interface, and the AP interface
is now different from the p2p management one).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add definitions and function prototypes for generic_cfg
command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for long intervals on sched scan.
If configured, the original request interval will
be used num_short_interval times, and then the
long interval will be used.
While on it, fix the scan command field names
to reflect the expected value is in ms (rather
than secs).
These values will be taken from the conf file,
so bump its version accordingly.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added support for a new time sync event
the event data contains the WiLink TSF value.
To trigger the event, a HW modification is required,
so as a supporting firmware binary.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit d8d2f19feb ("mwifiex: silence TDLS link delete failure
for nonexistent link") lowers the priority of error message when
TDLS link is already deleted. But it had got increased by
commit acebe8c10a ("mwifiex: change dbg print func to
mwifiex_dbg")
Reported-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch changes the state change behaviour of at86rf230 to always
TX_ARET mode. According the at86rf2xx datasheets TX_ARET mode doesn't
mean to be always waiting for ack frames after transmit. The transceiver
will automatically wait for ack frames or not if the acknowledge request
bit is set. See section "TX_ARET_ON – Transmit with Automatic Frame
Retransmission and CSMA-CA Retry".
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We will not release sdio bus until firmware is completely
downloaded and becomes ready. Our 8887 A2 chip can have
separate firmware images for WLAN and bluetooth. This
patch fixes an issue observed when both drivers
simultaneously try to download respective firmwares.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The commit "e29aa33 bna: Enable Multi Buffer RX" moved packets counter
increment from the beginning of the NAPI processing loop after the check
for erroneous packets so they are never accounted. This counter is used
to inform firmware about number of processed completions (packets).
As these packets are never acked the firmware fires IRQs for them again
and again.
Fixes: e29aa33 ("bna: Enable Multi Buffer RX")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PP2 controller is capable of per-CPU TX processing, which means there are
per-CPU banked register sets and queues. Current version of the driver supports
TX packet coalescing - once on given CPU sent packets amount reaches a threshold
value, an IRQ occurs. However, there is a single interrupt line responsible for
CPU0/1 TX and RX events (the latter is not per-CPU, the hardware does not
support RSS).
When the top-half executes the interrupt cause is not known. This is why in
NAPI poll function, along with RX processing, IRQ cause register on both
CPU's is accessed in order to determine on which of them the TX coalescing
threshold might have been reached. Thus the egress processing and releasing the
buffers is able to take place on the corresponding CPU. Hitherto approach lead
to an illegal usage of on_each_cpu function in softirq context.
The problem is solved by resigning from TX coalescing interrupts and separating
egress finalization from NAPI processing. For that purpose a method of using
hrtimer is introduced. In main transmit function (mvpp2_tx) buffers are released
once a software coalescing threshold is reached. In case not all the data is
processed a timer is set on this CPU - in its interrupt context a tasklet is
scheduled in which all queues are processed. At once only one timer per-CPU can
be running, which is controlled by a dedicated flag.
This commit removes TX processing from NAPI polling function, disables hardware
coalescing and enables hrtimer with tasklet, using new per-CPU port structure
(mvpp2_port_pcpu).
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp2 driver allows usage of per-CPU TX processing. Once the packets are
prepared independetly on each CPU, the hardware enqueues the descriptors in
common TX queue. After they are sent, the buffers and associated sk_buffs
should be released on the corresponding CPU.
This is why a special index is maintained in order to point to the right data to
be released after transmission takes place. Each per-CPU TX queue comprise an
array of sent sk_buffs, freed in mvpp2_txq_bufs_free function. However, the
index was used there also for obtaining a descriptor (and therefore a buffer to
be DMA-unmapped) from common TX queue, which was wrong, because it was not
referring to the current CPU.
This commit enables proper unmapping of sent data buffers by indexing them in
per-CPU queues using a dedicated array for keeping their physical addresses.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using spinlocks protection during one-time driver initialization is not
necessary. Moreover it resulted in invalid GFP_KERNEL allocation under the lock.
This commit removes redundant spinlocks from buffer manager part of mvpp2
initialization.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reported-by: Alexandre Fournier <alexandre.fournier@wisp-e.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MFD fixes from Lee Jones:
- fix dependency issues on ChromeOS platforms
- fix runtime PM issues on Arizona
- fix IRQ/suspend race on Arizona
* tag 'mfd-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: Remove MFD_CROS_EC_SPI depends on OF
platform/chrome: Don't make CHROME_PLATFORMS depends on X86 || ARM
mfd: arizona: Fix initialisation of the PM runtime
mfd: arizona: Fix race between runtime suspend and IRQs
Fix kernel-doc warning in libata-core.c:
Warning(..//drivers/ata/libata-core.c:4763): No description found for parameter 'tag'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
CTR hardware implementation does not match with kernel spec causing a counter bug
where just low 8 bytes are used for counter, when should be all 16bytes.
Since we already have other counter modes working according with specs
not worth to keep CTR itself on NX.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The PCI capabilities list for Intel DH895xCC VFs (device id 0x0443) with
QuickAssist Technology is prematurely terminated in hardware.
Workaround the issue by hard-coding the known expected next capability
pointer and saving the PCIE cap into internal buffer.
Patch generated against cryptodev-2.6
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adf admin and HW arbiter function can be used by dh895xcc specific code
well as the new dh895xccvf and future devices so moving them to
qat_common so that they can be shared.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The probe error path for this driver, for all intents and purposes,
is the talitos_remove() function due to the common "goto err_out".
Without this patch applied, talitos_remove() will panic under these
two conditions:
1. If the RNG device hasn't been registered via
talitos_register_rng() prior to entry into talitos_remove(),
then the attempt to unregister the RNG "device" will cause a panic.
2. If the priv->chan array has not been allocated prior to entry
into talitos_remove(), then the per-channel FIFO cleanup will panic
because of the dereference of that NULL "array".
Both of the above scenarios occur if talitos_probe_irq() fails.
This patch resolves issue #1 by introducing a boolean to mask the
hwrng_unregister() call in talitos_unregister_rng() if RNG device
registration was unsuccessful.
It resolves issue #2 by checking that priv->chan is not NULL in the
per-channel FIFO cleanup for loop.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
