We can use union for most of the temporary cruft (original ipv4/ipv6
address, source mac, physoutdev) since they're used during different
stages of br netfilter traversal.
Also get rid of the last two ->mask users.
Shrinks struct from 48 to 32 on 64bit arch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently nf_conntrack_proto_sctp module handles only packets between
primary addresses used to establish the connection. Any packets between
secondary addresses are classified as invalid so that usual firewall
configurations drop them. Allowing HEARTBEAT and HEARTBEAT-ACK chunks to
establish a new conntrack would allow traffic between secondary
addresses to pass through. A more sophisticated solution based on the
addresses advertised in the initial handshake (and possibly also later
dynamic address addition and removal) would be much harder to implement.
Moreover, in general we cannot assume to always see the initial
handshake as it can be routed through a different path.
The patch adds two new conntrack states:
SCTP_CONNTRACK_HEARTBEAT_SENT - a HEARTBEAT chunk seen but not acked
SCTP_CONNTRACK_HEARTBEAT_ACKED - a HEARTBEAT acked by HEARTBEAT-ACK
State transition rules:
- HEARTBEAT_SENT responds to usual chunks the same way as NONE (so that
the behaviour changes as little as possible)
- HEARTBEAT_ACKED responds to usual chunks the same way as ESTABLISHED
does, except the resulting state is HEARTBEAT_ACKED rather than
ESTABLISHED
- previously existing states except NONE are preserved when HEARTBEAT or
HEARTBEAT-ACK is seen
- NONE (in the initial direction) changes to HEARTBEAT_SENT on HEARTBEAT
and to CLOSED on HEARTBEAT-ACK
- HEARTBEAT_SENT changes to HEARTBEAT_ACKED on HEARTBEAT-ACK in the
reply direction
- HEARTBEAT_SENT and HEARTBEAT_ACKED are preserved on HEARTBEAT and
HEARTBEAT-ACK otherwise
Normally, vtag is set from the INIT chunk for the reply direction and
from the INIT-ACK chunk for the originating direction (i.e. each of
these defines vtag value for the opposite direction). For secondary
conntracks, we can't rely on seeing INIT/INIT-ACK and even if we have
seen them, we would need to connect two different conntracks. Therefore
simplified logic is applied: vtag of first packet in each direction
(HEARTBEAT in the originating and HEARTBEAT-ACK in reply direction) is
saved and all following packets in that direction are compared with this
saved value. While INIT and INIT-ACK define vtag for the opposite
direction, vtags extracted from HEARTBEAT and HEARTBEAT-ACK are always
for their direction.
Default timeout values for new states are
HEARTBEAT_SENT: 30 seconds (default hb_interval)
HEARTBEAT_ACKED: 210 seconds (hb_interval * path_max_retry + max_rto)
(We cannot expect to see the shutdown sequence so that, unlike
ESTABLISHED, the HEARTBEAT_ACKED timeout shouldn't be too long.)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When a connection is failing a transport protocol calls
dst_negative_advice to try to get a better route. This patch includes
changing the sk_txhash in that function. This provides a rudimentary
method to try to find a different path in the network since sk_txhash
affects ECMP on the local host and through the network (via flow labels
or UDP source port in encapsulation).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates sk_set_txhash and eliminates protocol specific
inet_set_txhash and ip6_set_txhash. sk_set_txhash simply sets a
random number instead of performing flow dissection. sk_set_txash
is also allowed to be called multiple times for the same socket,
we'll need this when redoing the hash for negative routing advice.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix three regressions, two recent ones (cpufreq core and ACPI
device power management) and one introduced during the 4.1 cycle
(intel_pstate).
Specifics:
- Fix a recently introduced issue in the cpufreq core causing it to
attempt to create duplicate symbolic links to the policy directory
in sysfs for CPUs that are offline when the cpufreq driver is being
registered (Rafael J Wysocki)
- Fix a recently introduced problem in the ACPI device power
management core code causing it to store an incorrect value in the
device object's power.state field in some cases which in turn leads
to attempts to turn power resources off while they should still be
on going forward (Mika Westerberg)
- Fix an intel_pstate driver issue introduced during the 4.1 cycle
which leads to kernel panics on boot on Knights Landing chips due
to incomplete support for them in that driver (Lukasz Anaczkowski)"
* tag 'pm+acpi-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Avoid attempts to create duplicate symbolic links
ACPI / PM: Use target_state to set the device power state
intel_pstate: Add get_scaling cpu_defaults param to Knights Landing
With the msi_list and the msi_domain properties now being at the
generic device level, it is starting to be relatively easy to offer
a generic way of providing non-PCI MSIs.
The two major hurdles with this idea are:
- Lack of global ID that identifies a device: this is worked around by
having a global ID allocator for each device that gets enrolled in
the platform MSI subsystem
- Lack of standard way to write the message in the generating device.
This is solved by mandating driver code to provide a write_msg
callback, so that everyone can have their own square wheel
Apart from that, the API is fairly straightforward:
- platform_msi_create_irq_domain creates an MSI domain that gets
tagged with DOMAIN_BUS_PLATFORM_MSI
- platform_msi_domain_alloc_irqs allocate MSIs for a given device,
populating the msi_list
- platform_msi_domain_free_irqs does what is written on the tin
[ tglx: Created a seperate struct platform_msi_desc and added
kerneldoc entries ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-10-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is not uncommon (at least with the ARM stuff) to have a piece
of hardware that implements different flavours of "interrupts".
A typical example of this is the GICv3 ITS, which implements
standard PCI/MSI support, but also some form of "generic MSI".
So far, the PCI/MSI domain is registered using the ITS device_node,
so that irq_find_host can return it. On the contrary, the raw MSI
domain is not registered with an device_node, making it impossible
to be looked up by another subsystem (obviously, using the same
device_node twice would only result in confusion, as it is not
defined which one irq_find_host would return).
A solution to this is to "type" domains that may be aliasing, and
to be able to lookup an device_node that matches a given type.
For this, we introduce irq_find_matching_host() as a superset
of irq_find_host:
struct irq_domain *irq_find_matching_host(struct device_node *node,
enum irq_domain_bus_token bus_token);
where bus_token is the "type" we want to match the domain against
(so far, only DOMAIN_BUS_ANY is defined). This result in some
moderately invasive changes on the PPC side (which is the only
user of the .match method).
This has otherwise no functionnal change.
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Conflicts:
drivers/acpi/scan.c
The conflict is resolved by moving the just introduced
acpi_device_is_first_physical_node() to bus.c and using
the existing acpi_companion_match() from there.
There will be an additional commit to combine the two.
Driver for the Resource Power Manager (RPM) found in Qualcomm 8974 based
devices.
The driver exposes resources that child drivers can operate on; to
implementing regulator, clock and bus frequency drivers.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This adds the Qualcomm Shared Memory Driver (SMD) providing
communication channels to remote processors, ontop of SMEM.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Pull SCSI target fixes from Nicholas Bellinger:
"This series is larger than what I'd normally be conformable with
sending for a -rc5 PULL request..
However, the bulk of the series is localized to qla2xxx target
specific fixes that address a number of real-world correctness issues,
that have been outstanding on the list for ~6 weeks now. They where
submitted + verified + acked by the HW LLD vendor, contributed by a
major production customer of the code, and are marked for v3.18.y
stable code.
That said, I don't see a good reason to wait another month to get
these fixes into mainline.
Beyond the qla2xx specific fixes, this series also includes:
- bugfix for a long standing use-after-free in iscsi-target during
TPG shutdown + demo-mode sessions.
- bugfix for a >= v4.0 regression OOPs in iscsi-target during a
iscsi_start_kthreads() failure.
- bugfix for a >= v4.0 regression hang in iscsi-target for iser
explicit session/connection logout.
- bugfix for a iser-target bug where a early CMA REJECTED status
during login triggers a NULL pointer dereference OOPs.
- bugfixes for a handful of v4.2-rc1 specific regressions related to
the larger set of recent backend configfs attribute changes.
A big thanks to QLogic + Pure Storage for the qla2xxx target bugfixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
Documentation/target: Fix tcm_mod_builder.py build breakage
iser-target: Fix REJECT CM event use-after-free OOPs
iscsi-target: Fix iser explicit logout TX kthread leak
iscsi-target: Fix iscsit_start_kthreads failure OOPs
iscsi-target: Fix use-after-free during TPG session shutdown
qla2xxx: terminate exchange when command is aborted by LIO
qla2xxx: drop cmds/tmrs arrived while session is being deleted
qla2xxx: disable scsi_transport_fc registration in target mode
qla2xxx: added sess generations to detect RSCN update races
qla2xxx: Abort stale cmds on qla_tgt_wq when plogi arrives
qla2xxx: delay plogi/prli ack until existing sessions are deleted
qla2xxx: cleanup cmd in qla workqueue before processing TMR
qla2xxx: kill sessions/log out initiator on RSCN and port down events
qla2xxx: fix command initialization in target mode.
qla2xxx: Remove msleep in qlt_send_term_exchange
qla2xxx: adjust debug flags
qla2xxx: release request queue reservation.
qla2xxx: Add flush after updating ATIOQ consumer index.
qla2xxx: Enable target mode for ISP27XX
qla2xxx: Fix hardware lock/unlock issue causing kernel panic.
...
Allocate usb otg descriptor and initialize it according to gadget's otg
capabilities, if usb_otg_caps is not set, keep settings as current gadget
drivers. With this 2 new interfaces, gadget can use usb_otg_descriptor
for OTG 1.x, and usb_otg20_descriptor for OTG 2.0 or above, and otg
features can be decided by the combination of usb hardware property
and driver config.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Check property of usb hardware to update otg version and disable SRP, HNP
and ADP if its disable flag is present.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add usb_otg_caps pointer to usb_gadget structure to indicate its
otg capabilities.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a structure usb_otg_caps to cover all otg related
capabilities of the device, including otg revision, and if hnp/srp/adp
is supported.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
OTG 2.0 introduces bcdOTG in otg descriptor to identify the OTG and EH
supplement release number with which the OTG device is compliant, this
patch adds structure usb_otg20_descriptor for OTG 2.0 and above.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces 'bind_deactivated' flag in struct usb_function.
Functions which don't want to be activated automatically after bind should
set this flag, and when they start to be ready to work they should call
usb_function_activate().
When USB function sets 'bind_deactivated' flag, initial deactivation
counter is incremented automatically, so there is no need to call
usb_function_deactivate() in function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These functions allows to deactivate gadget to make it not visible to
host and make it active again when gadget driver is finally ready.
They are needed to fix usb_function_activate() and usb_function_deactivate()
functions which currently are not working as usb_gadget_connect() is
called immediately after function bind regardless to previous calls of
usb_gadget_disconnect() function.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).
Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit bcf2843b3f8f added ->bi_error to cleanup the error passing
for struct bio, but that ended up adding 4 bytes and a 4 byte hole
to the size of struct bio. For a clean config, that bumped it from
128 bytes, to 136 bytes, on x86-64.
The ->bi_flags member is currently an unsigned long, but it fits
easily within an int. Change it to an unsigned int, adjust the
the pool offset code, and move ->bi_error into the new hole. Then
we end up with a 128 byte bio again.
Change the bio flag set/clear to use cmpxchg to ensure we don't
lose any flags when manipulating them.
Signed-off-by: Jens Axboe <axboe@fb.com>
Some places use helpers now, others don't. We only have the 'is set'
helper, add helpers for setting and clearing flags too.
It was a bit of a mess of atomic vs non-atomic access. With
BIO_UPTODATE gone, we don't have any risk of concurrent access to the
flags. So relax the restriction and don't make any of them atomic. The
flags that do have serialization issues (reffed and chained), we
already handle those separately.
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Restart the tick when necessary from the irq exit path. It makes nohz
full more flexible, simplify the related IPIs and doesn't bring
significant overhead on irq exit.
In a longer term view, it will allow us to piggyback the nohz kick
on the scheduler IPI in the future instead of sending a dedicated IPI
that often doubles the scheduler IPI on task wakeup. This will require
more changes though including careful review of resched_curr() callers
to include nohz full needs.
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Normally the tilegx networking shim sends irqs to all the cores
to distribute the load of processing incoming-packet interrupts,
so that you can get to multiple Gb's of traffic inbound.
However, in nohz_full mode we don't want to interrupt the
nohz_full cores by default, so we limit the set of cores we use
to only the online housekeeping cores.
To make client code easier to read, we introduce a new nohz_full
accessor, housekeeping_cpumask(), which returns a pointer to the
housekeeping_mask if nohz_full is enabled, and otherwise returns
the cpu_possible_mask.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Add helper iterator macros for iterating over the source and sink paths of
widget. This will make it easier to change the implementation later on.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds names for missing irq types to the trace events.
In order to identify adapter irqs, the define is moved from
interrupt.c to the other basic irq defines in uapi/linux/kvm.h.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
As all dwmac-* drivers have been converted to have a proper probe
function the setup callback can now be removed. Also remove the
free callback that wasn't used by any driver.
New dwmac-* drivers should implement standard probe and remove
functions to preform any needed setup and teardown.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As dwmac-* drivers that need OF match have been converted
to use their own internal OF match data structure this can
now be removed.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors in a Qualcomm platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Let's encourage const arrays of parent names like other basic
clock types.
Cc: Sergej Sawazki <ce3a@gmx.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
