* pci/iommu:
of: Calculate device DMA masks based on DT dma-range size
arm: dma-mapping: limit IOMMU mapping size
PCI: Update DMA configuration from DT
of/pci: Add of_pci_dma_configure() to update DMA configuration
PCI: Add helper functions pci_get[put]_host_bridge_device()
of: Fix size when dma-range is not used
of: Move of_dma_configure() to device.c to help re-use
of: iommu: Add ptr to OF node arg to of_iommu_configure()
* pci/resource:
PCI: Fail pci_ioremap_bar() on unassigned resources
PCI: Show driver, BAR#, and resource on pci_ioremap_bar() failure
PCI: Mark invalid BARs as unassigned
PNP: Don't check for overlaps with unassigned PCI BARs
Since fab4085 ("netfilter: log: nf_log_packet() as real unified
interface"), the loginfo structure that is passed to nf_log_packet() is
used to explicitly indicate the logger type you want to use.
This is a problem for people tracing rules through nfnetlink_log since
packets are always routed to the NF_LOG_TYPE logger after the
aforementioned patch.
We can fix this by removing the trace loginfo structures, but that still
changes the log level from 4 to 5 for tracing messages and there may be
someone relying on this outthere. So let's just introduce a new
nf_log_trace() function that restores the former behaviour.
Reported-by: Markus Kötter <koetter@rrzn.uni-hannover.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
These functions do not belong in <asm-generic/gpio.h> since the
split into separate GPIO headers under <linux/gpio/*>. Move them
to <linux/gpio/driver.h> as is apropriate.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a networking device is taken down that has a non-trivial number
of VLAN devices configured under it, we eat a full synchronize_net()
for every such VLAN device.
This is because of the call chain:
NETDEV_DOWN notifier
--> vlan_device_event()
--> dev_change_flags()
--> __dev_change_flags()
--> __dev_close()
--> __dev_close_many()
--> dev_deactivate_many()
--> synchronize_net()
This is kind of rediculous because we already have infrastructure for
batching doing operation X to a list of net devices so that we only
incur one sync.
So make use of that by exporting dev_close_many() and adjusting it's
interfaace so that the caller can fully manage the batch list. Use
this in vlan_device_event() and all the overhead goes away.
Reported-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to port id allow netdevices to specify port names and export
the name via sysfs. Drivers can implement the netdevice operation to
assist udev in having sane default names for the devices using the
rule:
$ cat /etc/udev/rules.d/80-net-setup-link.rules
SUBSYSTEM=="net", ACTION=="add", ATTR{phys_port_name}!="",
NAME="$attr{phys_port_name}"
Use of phys_name versus phys_id was suggested-by Jiri Pirko.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in favor of their inner __ ones, which doesn't grab rtnl.
As these functions need to operate on a locked socket, we can't be
grabbing rtnl by then. It's too late and doing so causes reversed
locking.
So this patch:
- move rtnl handling to callers instead while already fixing some
reversed locking situations, like on vxlan and ipvs code.
- renames __ ones to not have the __ mark:
__ip_mc_{join,leave}_group -> ip_mc_{join,leave}_group
__ipv6_sock_mc_{join,drop} -> ipv6_sock_mc_{join,drop}
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be able to use sk_ehashfn() for request socks,
we need to initialize their IPv6/IPv4 addresses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now always call __inet_hash_nolisten(), no need to pass it
as an argument.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now use inet_hash() and __inet_hash() instead of private
functions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intent is to converge IPv4 & IPv6 inet_hash functions to
factorize code.
IPv4 sockets initialize sk_rcv_saddr and sk_v6_daddr
in this patch, thanks to new sk_daddr_set() and sk_rcv_saddr_set()
helpers.
__inet6_hash can now use sk_ehashfn() instead of a private
inet6_sk_ehashfn() and will simply use __inet_hash() in a
following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Goal is to unify IPv4/IPv6 inet_hash handling, and use common helpers
for all kind of sockets (full sockets, timewait and request sockets)
inet_sk_ehashfn() becomes sk_ehashfn() but still only copes with IPv4
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
const qualifiers ease code review by making clear
which objects are not written in a function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tpm_i2c_stm_st33 is a TIS 1.2 TPM with a core interface which can be used
by different phy such as i2c or spi. The core part is called st33zp24 which
is also the main part reference.
include/linux/platform_data/tpm_stm_st33.h is renamed consequently.
The driver is also split into an i2c phy in charge of sending/receiving
data as well as managing platform data or dts configuration.
Acked-by: Jarkko Sakkinen <jarkko.sakknen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This patch introduces the module_pnp_driver macro which is a
convenience macro for PNP driver modules similar to module_pci_driver.
It is intended to be used by drivers which init/exit section does nothing
but register/unregister the PNP driver. By using this macro it is
possible to eliminate a few lines of boilerplate code per PNP driver.
Based on work done by Lars-Peter Clausen <lars@metafoo.de> for other
busses (i2c and spi) and Greg KH for PCI.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds support for a new quota type PRJQUOTA for project quota
enforcement. Also a new method get_projid() is added into dquot_operations
structure.
Signed-off-by: Li Xi <lixi@ddn.com>
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jan Kara <jack@suse.cz>
Add the low-level device commands and definitions used for QP max-rate limiting.
This is done through the following elements:
- read rate-limit device caps in QUERY_DEV_CAP: number of different
rates and the min/max rates in Kbs/Mbs/Gbs units
- enhance the QP context struct to contain rate limit units and value
- allow to do run time rate-limit setting to QPs through the
update-qp firmware command
- QP rate-limiting is disallowed for VFs
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a tx_maxrate attribute to the tx queue sysfs entry allowing
for max-rate limiting. Along with DCB-ETS and BQL this provides another
knob to tune queue performance. The limit units are Mbps.
By default it is disabled. To disable the rate limitation after it
has been set for a queue, it should be set to zero.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull livepatching fix from Jiri Kosina:
- fix for potential race with module loading, from Petr Mladek.
The race is very unlikely to be seen in real world and has been found
by code inspection, but should be fixed for 4.0 anyway.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Fix subtle race with coming and going modules
The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.
Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.
This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.
The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the parameters max_size and min_size which are
meant to replace max_shift and min_shift.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently no umc drivers implementing suspend/resume, so remove
the legacy suspend/resume support from the framework. If a umc driver ever
wants to implement suspend/resume they can use dev_pm_ops, which works out
of the box without any additional support necessary from the bus itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some usb PHYs need power supply from vbus to make it work, eg mxs-phy, if
there is no vbus, USB PHY will not in correct state when the controller starts
to work, for host, this requires vbus should be turned on before setting port
power(PP) of ehci, to work with this kind of USB PHY design, this patch adds
a flag CI_HDRC_TURN_VBUS_EARLY_ON, can be checked by host driver to turn on
vbus while start host.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally, the system can't come back up after suspend/resume
due to problems of device suspending phase. This patch make
PM_TRACE infrastructure cover device suspending phase of
suspend/resume process, and the information in RTC can tell
developers which device suspending function make system hang.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I2C supports adding adapters using either a dynamic or fixed id. The
latter is provided by aliases in the DT case. To prevent id collisions
of those two types, install this function which gives us the highest
fixed id, so we can then let the dynamically created ones come after
this highest number.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently when version 3.1 of the mx6q SDMA firmware is used we get:
[ 0.392169] imx-sdma 20ec000.sdma: unknown firmware version
[ 0.399281] imx-sdma 20ec000.sdma: initialized
Add support for it.
Based on a patch from Shengjiu Wang from the internal FSL kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
While testing last patch series, I found req sock refcounting was wrong.
We must set skc_refcnt to 1 for all request socks added in hashes,
but also on request sockets created by FastOpen or syncookies.
It is tricky because we need to defer this initialization so that
future RCU lookups do not try to take a refcount on a not yet
fully initialized request socket.
Also get rid of ireq_refcnt alias.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 13854e5a60 ("inet: add proper refcounting to request sock")
Signed-off-by: David S. Miller <davem@davemloft.net>
The listener field in struct tcp_request_sock is a pointer
back to the listener. We now have req->rsk_listener, so TCP
only needs one boolean and not a full pointer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we'll be able to lookup request sockets in ehash table,
we'll need to get access to listener which created this request.
This avoid doing a lookup to find the listener, which benefits
for a more solid SO_REUSEPORT, and is needed once we no
longer queue request sock into a listener private queue.
Note that 'struct tcp_request_sock'->listener could be reduced
to a single bit, as TFO listener should match req->rsk_listener.
TFO will no longer need to hold a reference on the listener.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_reqsk_alloc() is becoming fat and should not be inlined.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
listener socket can be used to set net pointer, and will
be later used to hold a reference on listener.
Add a const qualifier to first argument (struct request_sock_ops *),
and factorize all write_pnet(&ireq->ireq_net, sock_net(sk));
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mediatek SoCs have GPIO controller that handle both the muxing and GPIOs.
The GPIO controller have pinmux, pull enable, pull select, direction and output high/low control.
This driver include common driver and mt8135 part.
The common driver include the pinctrl driver and GPIO driver.
The mt8135 part contain its special device data.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dai-link params for codec-codec links were fixed. The fixed
link between codec and another chip which may be another codec,
baseband, bluetooth codec etc may require run time configuaration
changes. This change provides an optional alsa control to select
one of the params from a list of params.
Signed-off-by: Nikesh Oswal <nikesh@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setup new I915_GETPARAM ioctl entries for subslice total and
EU total. Userspace drivers need these values when constructing
GPGPU commands. This kernel query method is intended to replace
the PCI ID-based tables that userspace drivers currently maintain.
The kernel driver can employ fuse register reads as needed to
ensure the most accurate determination of GT config attributes.
This first became important with Cherryview in which the config
could differ between devices with the same PCI ID.
The kernel detection of these values is device-specific and not
included in this patch. Because zero is not a valid value for any of
these parameters, a value of zero is interpreted as unknown for the
device. Userspace drivers should continue to maintain ID-based tables
for older devices not supported by the new query method.
v2: Increment our I915_GETPARAM indices to fit after REVISION
which was merged ahead of us.
For: VIZ-4636
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Tested-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Acked-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Spell all the PCI IDs out to be able to quickly grep for the IDs. No
functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Add GT1/2 to comments to not loose that distinction.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I have no idea about the exact rules, but this angered Dave's 32bit
rhel gcc.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Adds a parameter which can be used with DRM_I915_GETPARAM to query the
GPU revision. The intention is to use this in Mesa to implement the
WaDisableSIMD16On3SrcInstr workaround on Skylake but only for
revision 2.
Signed-off-by: Neil Roberts <neil@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
tcp_oow_rate_limited() is hardly used in fast path, there is
no point inlining it.
Signed-of-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big helper is called once from tcp_conn_request(), there is no
point having it in an include. Compiler will inline it anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64bit arches, we can save 8 bytes in inet_request_sock
by moving ir_mark to fill a hole.
While we are at it, inet_request_mark() can get a const qualifier
for listener socket.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
