At the moment modesetting pipe C on IVB will fail if pipe B uses 4 FDI
lanes. Make the BW sharing more dynamic by trying to reduce pipe B's
link bpp in this case, until pipe B uses only up to 2 FDI lanes.
For this instead of the encoder compute config retry loop - which
reduced link bpp only for the encoder's pipe - reduce the maximum link
bpp for pipe B/C as required after all CRTC states are computed and
recompute the CRTC states with the new bpp limit.
Atm, all FDI encoder's compute config function returns an error if a BW
constrain prevents increasing the pipe bpp value. The corresponding
crtc_state->bw_constrained check can be replaced with checking
crtc_state->max_link_bpp_x16, add TODO comments for this. SDVO is an
exception where this case is only handled in the outer config retry
loop, failing the modeset with a WARN, add a FIXME comment to handle
this in the encoder code similarly to other encoders.
v2:
- Don't assume that a CRTC is already in the atomic state, while
reducing its link bpp.
- Add DocBook description to intel_fdi_atomic_check_link().
v3:
- Enable BW management for FDI links in a separate patch. (Ville)
v4: (Ville)
- Fail the SDVO encoder config computation if it doesn't support the
link bpp limit.
- Add TODO: comments about checking link_bpp_x16 instead of
bw_constrained.
v5:
- Replace link bpp limit check with a FIXME: comment in
intel_sdvo_compute_config(). (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Amended commit message wrt. changes in v5]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921195159.2646027-11-imre.deak@intel.com
Each SDVO device can have up to three sets of DDC pins.
Currently we just register a single i2c_adapter for the
entire SDVO device and semi-randomly pick the "correct"
set of DDC pins during intel_sdvo_tmds_sink_detect().
This doesn't make any real sense especially if we have
multiple outputs each with their own dedicated DDC bus.
Let's clean up this mess and register a dedicated
i2c_adapter for each of the possible pin pairs. Each
output (ie. connector) can then pick the correct i2c_adapter
to use for its DDC bus. And we can just switch over to
drm_connector_init_with_ddc() to take care of the
connector->ddc association, which also populates the
"ddc" sysfs symlink as a bonus.
And now that things are based on the actual connector we can
also nuke the sketchy sdvo->controller_output thing.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825134431.24391-6-ville.syrjala@linux.intel.com
The SDVO code already warns when the port in question doesn't
actually support SDVO. Let's make that also bail the encoder
registration like the generic assert_port_valid() we added.
And add a similar thing for g4x HDMI, mainly because on g4x
itsefl port D only supports DP but not SDVO/HDMI. For the
other platforms the generic port_mask check should actually
be sufficient, but since we're here might as well list the
ports.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-6-ville.syrjala@linux.intel.com
Sprinkle some asserts to catch any mishaps in the port_mask
vs. output init.
For DDI/DP/HDMI/SDVO I decided that we want to bail out for
an invalid port since those are the encoder types where
we might want consider driving the whole thing from the VBT
child device list, and bogus VBTs could be a real issue
(if for no other reason than the i915.vbt_firmware).
For DVO and HSW/BDW CRT port I just threw the assert in
there for good measure.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-5-ville.syrjala@linux.intel.com
The decision to use DFP output format conversion capabilities should be
during compute_config phase.
This patch adds new member to crtc_state to represent the final
output_format to the sink. In case of a DFP this can be different than
the output_format, as per the format conversion done via the PCON.
This will help to store only the format conversion capabilities of the
DP device in intel_dp->dfp, and use crtc_state to compute and store the
configuration for color/format conversion for a given mode.
v2: modified the new member to crtc_state to represent the final
output_format that eaches the sink, after possible conversion by
PCON kind of devices. (Ville)
v3: Addressed comments from Ville:
-Added comments to clarify difference between sink_format and
output_format.
-Corrected the order of setting sink_format and output_format.
-Added readout for sink_format in get_pipe_config hooks.
v4: Set sink_format for intel_sdvo too. (Ville)
v5: Rebased.
v6: Fixed condition to go for YCbCr420 format for dp and hdmi. (Ville)
v7: Fix the condition to set sink_format for HDMI.
Set hdmi output_format simply as sink_format. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-2-ankit.k.nautiyal@intel.com
Lots of ADL machines out there with bogus VBTs that declare
two eDP child devices. In order for those to work we need to
figure out which power sequencer to use before we try the EDID
read. So let's do the panel VBT init early if we can, falling
back to the post-EDID init otherwise.
The post-EDID init panel_type=0xff approach of assuming the
power sequencer should already be enabled doesn't really work
with multiple eDP panels, and currently we just end up using
the same power sequencer for both eDP ports, which at least
confuses the wakeref tracking, and potentially also causes us
to toggle the VDD for the panel when we should not.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-3-ville.syrjala@linux.intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
Each LFP may have different panel type which is stored in LFP data
data block. Based on the child device index respective panel-type/
panel-type2 field will be used.
v1: Initial rfc verion.
v2: Based on review comments from Jani,
- Used panel-type instead addition panel-index variable.
- DEVICE_HANDLE_* name changed and placed before DEVICE_TYPE_*
macro.
v3:
- passing intel_bios_encoder_data as argument of
intel_bios_init_panel(). Passing NULL to indicate encoder is not
initialized yet for dsi as current focus is to enable dual EDP. [Jani]
v4:
- encoder->devdata used which is initialized before from vbt
structure. [Jani]
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620065138.5126-1-animesh.manna@intel.com
Move the panel specific VBT parsing to happen during the
output probing stage. Needs to be done because the VBT
parsing will need to look at the EDID to determine
the correct panel_type on some machines.
We split the parsed VBT data (i915->vbt) along the same
boundary. For the moment we just hoist all the panel
specific stuff into connector->panel.vbt since that seems
like the most convenient place for eg. the backlight code.
Note that we simply drop the drrs type check from
intel_drrs_frontbuffer_update() since that operates on the whole
device rather than a specific connector/encoder. But the check
was just a micro optimization so removing it doesn't actually
mattter for correctness.
TODO: Lot's of cleanup to be done in the future. Eg. most of
the DSI stuff could probably be eliminated entirely and just
parsed on demand during DSI init.
v2: Note the intel_drrs_frontbuffer_update() change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.
The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.
Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.
v3:
* fix Kconfig dependencies (Javier)
v2:
* reduce HDMI helpers to avoid exporting functions (Jani)
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-8-tzimmermann@suse.de
Rather than having the connector init get the fixed mode back from
intel_panel and then feed it straight back into intel_panel_init()
let's just make the fixed mode lookup put the mode directly onto
the panel's fixed_modes list. Avoids the pointless round trip and
opens the door for further enhancements to the fixed mode handling.
v2: Make the debug message correct by using intel_panel_drrs_type() (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
