The embedded struct cdev does not have its lifetime correctly tied to
the enclosing struct f_hidg, so there is a use-after-free if /dev/hidgN
is held open while the gadget is deleted.
This can readily be replicated with libusbgx's example programs (for
conciseness - operating directly via configfs is equivalent):
gadget-hid
exec 3<> /dev/hidg0
gadget-vid-pid-remove
exec 3<&-
Pull the existing device up in to struct f_hidg and make use of the
cdev_device_{add,del}() helpers. This changes the lifetime of the
device object to match struct f_hidg, but note that it is still added
and deleted at the same time.
Fixes: 71adf11894 ("USB: gadget: add HID gadget driver")
Tested-by: Lee Jones <lee@kernel.org>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20221122123523.3068034-2-john@metanate.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the process of switching USB config from rndis to other config,
if the hardware does not support the ->pullup callback, or the
hardware encounters a low probability fault, both of them may cause
the ->pullup callback to fail, which will then cause a system panic
(use after free).
The gadget drivers sometimes need to be unloaded regardless of the
hardware's behavior.
Analysis as follows:
=======================================================================
(1) write /config/usb_gadget/g1/UDC "none"
gether_disconnect+0x2c/0x1f8
rndis_disable+0x4c/0x74
composite_disconnect+0x74/0xb0
configfs_composite_disconnect+0x60/0x7c
usb_gadget_disconnect+0x70/0x124
usb_gadget_unregister_driver+0xc8/0x1d8
gadget_dev_desc_UDC_store+0xec/0x1e4
(2) rm /config/usb_gadget/g1/configs/b.1/f1
rndis_deregister+0x28/0x54
rndis_free+0x44/0x7c
usb_put_function+0x14/0x1c
config_usb_cfg_unlink+0xc4/0xe0
configfs_unlink+0x124/0x1c8
vfs_unlink+0x114/0x1dc
(3) rmdir /config/usb_gadget/g1/functions/rndis.gs4
panic+0x1fc/0x3d0
do_page_fault+0xa8/0x46c
do_mem_abort+0x3c/0xac
el1_sync_handler+0x40/0x78
0xffffff801138f880
rndis_close+0x28/0x34
eth_stop+0x74/0x110
dev_close_many+0x48/0x194
rollback_registered_many+0x118/0x814
unregister_netdev+0x20/0x30
gether_cleanup+0x1c/0x38
rndis_attr_release+0xc/0x14
kref_put+0x74/0xb8
configfs_rmdir+0x314/0x374
If gadget->ops->pullup() return an error, function rndis_close() will be
called, then it will causes a use-after-free problem.
=======================================================================
Fixes: 0a55187a1e ("USB: gadget core: Issue ->disconnect() callback from usb_gadget_disconnect()")
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: TaoXue <xuetao09@huawei.com>
Link: https://lore.kernel.org/r/20221121130805.10735-1-water.zhangjiantao@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget may change over bind/unbind cycles, so set it each time during
bind, not only the first time. Without it we get a use-after-free with
the following example:
cd /sys/kernel/config/usb_gadget/; mkdir -p mygadget; cd mygadget
mkdir -p configs/c.1/strings/0x409
echo "C1:Composite Device" > configs/c.1/strings/0x409/configuration
mkdir -p functions/ecm.usb0
ln -s functions/ecm.usb0 configs/c.1/
rmmod dummy_hcd
modprobe dummy_hcd
KASAN will complain shortly after the 'modprobe':
usb 2-1: New USB device found, idVendor=0000, idProduct=0000, bcdDevice= 6.01
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
==================================================================
BUG: KASAN: use-after-free in gether_connect+0xb8/0x30c
Read of size 4 at addr cbef170c by task swapper/3/0
CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.1.0-rc3-00014-g41ff012f50cb-dirty #322
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from print_report+0x134/0x4d4
print_report from kasan_report+0x78/0x10c
kasan_report from gether_connect+0xb8/0x30c
gether_connect from ecm_set_alt+0x124/0x254
ecm_set_alt from composite_setup+0xb98/0x2b18
composite_setup from configfs_composite_setup+0x80/0x98
configfs_composite_setup from dummy_timer+0x8f0/0x14a0 [dummy_hcd]
...
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221104131031.850850-3-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UDC is not a suitable parent of the net device as the UDC can
change or vanish during the lifecycle of the ethernet gadget. This
can be illustrated with the following:
mkdir -p /sys/kernel/config/usb_gadget/mygadget
cd /sys/kernel/config/usb_gadget/mygadget
mkdir -p configs/c.1/strings/0x409
echo "C1:Composite Device" > configs/c.1/strings/0x409/configuration
mkdir -p functions/ecm.usb0
ln -s functions/ecm.usb0 configs/c.1/
echo "dummy_udc.0" > UDC
rmmod dummy_hcd
The 'rmmod' removes the UDC from the just created gadget, leaving
the still existing net device with a no longer existing parent.
Accessing the ethernet device with commands like:
ip --details link show usb0
will result in a KASAN splat:
==================================================================
BUG: KASAN: use-after-free in if_nlmsg_size+0x3e8/0x528
Read of size 4 at addr c5c84754 by task ip/357
CPU: 3 PID: 357 Comm: ip Not tainted 6.1.0-rc3-00013-gd14953726b24-dirty #324
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from print_report+0x134/0x4d4
print_report from kasan_report+0x78/0x10c
kasan_report from if_nlmsg_size+0x3e8/0x528
if_nlmsg_size from rtnl_getlink+0x2b4/0x4d0
rtnl_getlink from rtnetlink_rcv_msg+0x1f4/0x674
rtnetlink_rcv_msg from netlink_rcv_skb+0xb4/0x1f8
netlink_rcv_skb from netlink_unicast+0x294/0x478
netlink_unicast from netlink_sendmsg+0x328/0x640
netlink_sendmsg from ____sys_sendmsg+0x2a4/0x3b4
____sys_sendmsg from ___sys_sendmsg+0xc8/0x12c
___sys_sendmsg from sys_sendmsg+0xa0/0x120
sys_sendmsg from ret_fast_syscall+0x0/0x1c
Solve this by not setting the parent of the ethernet device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221104131031.850850-2-s.hauer@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Faraday FOTG210 is a dual-mode OTG USB controller that can
act as host, peripheral or both. To be able to probe from one
hardware description and to follow the pattern of other dual-
mode controllers such as MUSB or MTU3 we need to collect the
two, currently completely separate drivers in the same
directory.
After this, users need to select the main symbol USB_FOTG210
and then each respective subdriver. We pave the road to
compile both drivers into the same kernel and select the
one we want to use at probe() time, and possibly add OTG
support in the end.
This patch doesn't do much more than create the new symbol
and collect the drivers in one place. We also add a comment
for the section of dual-mode controllers in the Kconfig
file so people can see what these selections are about.
Also add myself as maintainer as there has been little
response on my patches to these drivers.
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221023144708.3596563-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ast_vhub_epn_handle_ack() when the received data length exceeds the
buffer, it does not check the case and just copies to req.buf and cause
a buffer overflow, kernel oops on this case.
This issue could be reproduced on a BMC with an OS that enables the
lan over USB:
1. In OS, enable the usb eth dev, verify it pings the BMC OK;
2. In OS, set the usb dev mtu to 2000. (Default is 1500);
3. In OS, ping the BMC with `-s 2000` argument.
The BMC kernel will get oops with below logs:
skbuff: skb_over_panic: text:8058e098 len:2048 put:2048 head:84c678a0 data:84c678c2 tail:0x84c680c2 end:0x84c67f00 dev:usb0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
Internal error: Oops - BUG: 0 [#1] ARM
CPU: 0 PID: 0 Comm: swapper Not tainted 5.15.69-c9fb275-dirty-d1e579a #1
Hardware name: Generic DT based system
PC is at skb_panic+0x60/0x6c
LR is at irq_work_queue+0x6c/0x94
Fix the issue by checking the length and set `-EOVERFLOW`.
Tested: Verify the BMC kernel does not get oops in the above case, and
the usb ethernet gets RX packets errors instead.
Signed-off-by: Lei YU <yulei.sh@bytedance.com>
Signed-off-by: Henry Tian <tianxiaofeng@bytedance.com>
Reviewed-by: Neal Liu <neal_liu@aspeedtech.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: https://lore.kernel.org/r/20221024094853.2877441-1-yulei.sh@bytedance.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 19905240ae.
It was a new feature, and it doesn't even work properly yet, so revert
it from this branch as it is not needed for 6.1-final.
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@kernel.org>
Fixes: 19905240ae ("usb: gadget: uvc: limit isoc_sg to super speed gadgets")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the userspace it is needed to distinguish between requests for the
control or streaming interface. The userspace would have to parse the
configfs to know which interface index it has to compare the ctrl
requests against. Since the interface numbers are not fixed, e.g. for
composite gadgets, the interface offset depends on the setup.
The kernel has this information when handing over the ctrl request to
the userspace. This patch removes the offset from the interface numbers
and expose the default interface defines in the uapi g_uvc.h.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20221011075348.1786897-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit fc274c1e99 ("USB: gadget: Add a new bus for gadgets"),
the gadget devices are proper driver core devices, which caused each
device to request pinmux settings:
aspeed_vhub 1e6a0000.usb-vhub: Initialized virtual hub in USB2 mode
aspeed-g5-pinctrl 1e6e2080.pinctrl: pin A7 already requested by 1e6a0000.usb-vhub; cannot claim for gadget.0
aspeed-g5-pinctrl 1e6e2080.pinctrl: pin-232 (gadget.0) status -22
aspeed-g5-pinctrl 1e6e2080.pinctrl: could not request pin 232 (A7) from group USB2AD on device aspeed-g5-pinctrl
g_mass_storage gadget.0: Error applying setting, reverse things back
The vhub driver has already claimed the pins, so prevent the gadgets
from requesting them too by setting the magic of_node_reused flag. This
causes the driver core to skip the mux request.
Reported-by: Zev Weiss <zev@bewilderbeest.net>
Reported-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Fixes: fc274c1e99 ("USB: gadget: Add a new bus for gadgets")
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Link: https://lore.kernel.org/r/20221017053006.358520-1-joel@jms.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there is a transmission error the buffer will be returned too early,
causing a memory fault as subsequent requests for that buffer are still
queued up to be sent. Refactor the error handling to wait for the final
request to come in before reporting back the buffer to userspace for all
transfer types (bulk/isoc/isoc_sg). This ensures userspace knows if the
frame was successfully sent.
Fixes: e81e7f9a0e ("usb: gadget: uvc: add scatter gather support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20221018215044.765044-4-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
With the patch "588b9e85609b (usb: gadget: uvc: add v4l2 enumeration api
calls)" the driver is keeping a list of configfs entries currently
configured. The list is used in uvc_v4l2 on runtime.
The driver now is giving back the list item just after it was referenced
with config_item_put. It also calls config_item_put on uvc_free, which
is the only and right place to give back the reference. This patch fixes
the issue by removing the extra config_item_put in uvc_alloc.
Fixes: 588b9e8560 (usb: gadget: uvc: add v4l2 enumeration api calls)
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220930122839.1747279-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building s390 allmodconfig after commit 9b91a65230 ("usb: gadget:
uvc: increase worker prio to WQ_HIGHPRI"), the following error occurs:
In file included from ../include/linux/string.h:253,
from ../include/linux/bitmap.h:11,
from ../include/linux/cpumask.h:12,
from ../include/linux/smp.h:13,
from ../include/linux/lockdep.h:14,
from ../include/linux/rcupdate.h:29,
from ../include/linux/rculist.h:11,
from ../include/linux/pid.h:5,
from ../include/linux/sched.h:14,
from ../include/linux/ratelimit.h:6,
from ../include/linux/dev_printk.h:16,
from ../include/linux/device.h:15,
from ../drivers/usb/gadget/function/f_uvc.c:9:
In function ‘fortify_memset_chk’,
inlined from ‘uvc_register_video’ at ../drivers/usb/gadget/function/f_uvc.c:424:2:
../include/linux/fortify-string.h:301:25: error: call to ‘__write_overflow_field’ declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
301 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This points to the memset() in uvc_register_video(). It is clear that
the argument to sizeof() is incorrect, as uvc->vdev (a 'struct
video_device') is being zeroed out but the size of uvc->video (a 'struct
uvc_video') is being used as the third arugment to memset().
pahole shows that prior to commit 9b91a65230 ("usb: gadget: uvc:
increase worker prio to WQ_HIGHPRI"), 'struct video_device' and
'struct ucv_video' had the same size, meaning that the argument to
sizeof() is incorrect semantically but there is no visible issue:
$ pahole -s build/drivers/usb/gadget/function/f_uvc.o | grep -E "(uvc_video|video_device)\s+"
video_device 1400 4
uvc_video 1400 3
After that change, uvc_video becomes slightly larger, meaning that the
memset() will overwrite by 8 bytes:
$ pahole -s build/drivers/usb/gadget/function/f_uvc.o | grep -E "(uvc_video|video_device)\s+"
video_device 1400 4
uvc_video 1408 3
Fix the arugment to sizeof() so that there is no overwrite.
Cc: stable@vger.kernel.org
Fixes: e4ce9ed835 ("usb: gadget: uvc: ensure the vdev is unset")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220928201921.3152163-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When opts->pnp_string is changed with configfs, new memory is allocated for
the string. It does not, however, update dev->pnp_string, even though the
memory is freed. When rquesting the string, the host then gets old or
corrupted data rather than the new string. The ieee 1284 id string should
be allowed to change while the device is connected.
The bug was introduced in commit fdc01cc286 ("usb: gadget: printer:
Remove pnp_string static buffer"), which changed opts->pnp_string from a
char[] to a char*.
This patch changes dev->pnp_string from a char* to a char** pointing to
opts->pnp_string.
Fixes: fdc01cc286 ("usb: gadget: printer: Remove pnp_string static buffer")
Signed-off-by: Albert Briscoe <albertsbriscoe@gmail.com>
Link: https://lore.kernel.org/r/20220911223753.20417-1-albertsbriscoe@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is changing the simple workqueue in the gadget driver to be
allocated as async_wq with a higher priority. The pump worker, that is
filling the usb requests, will have a higher priority and will not be
scheduled away so often while the video stream is handled. This will
lead to fewer streaming underruns.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220907215818.2670097-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This from static analysis. The vla_item() takes a size and adds it to
the total. It has a built in integer overflow check so if it encounters
an integer overflow anywhere then it records the total as SIZE_MAX.
However there is an issue here because the "lang_count*(needed_count+1)"
multiplication can overflow. Technically the "lang_count + 1" addition
could overflow too, but that would be detected and is harmless. Fix
both using the new size_add() and size_mul() functions.
Fixes: e6f3862fa1 ("usb: gadget: FunctionFS: Remove VLAIS usage from gadget code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YxDI3lMYomE7WCjn@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves the merge issue in:
drivers/usb/dwc3/gadget.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As follows from #define NAME_TEMPLATE, the procfs code in the RNDIS driver
expects the # of instances to be 3-digit decimal, while the driver calls
ida_simple_get() passing 0 as the 'end' argument which results in actual
max instance # of INT_MAX. Limit the maximum # of RNDIS instances to 1000
which is still a lot! :-)
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/a8180973-3ded-3644-585a-169589a37642@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During cdrom emulation, the response to read_toc command must contain
the cdrom address as the number of sectors (2048 byte sized blocks)
represented either as an absolute value (when MSF bit is '0') or in
terms of PMin/PSec/PFrame (when MSF bit is set to '1'). Incase of
cdrom, the fsg_lun_open call sets the sector size to 2048 bytes.
When MAC OS sends a read_toc request with MSF set to '1', the
store_cdrom_address assumes that the address being provided is the
LUN size represented in 512 byte sized blocks instead of 2048. It
tries to modify the address further to convert it to 2048 byte sized
blocks and store it in MSF format. This results in data transfer
failures as the cdrom address being provided in the read_toc response
is incorrect.
Fixes: 3f565a363c ("usb: gadget: storage: adapt logic block size to bound block devices")
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1661570110-19127-1-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit expanding the scope of the udc_lock mutex in the
gadget core managed to cause an obscure and slightly bizarre lockdep
violation. In abbreviated form:
======================================================
WARNING: possible circular locking dependency detected
5.19.0-rc7+ #12510 Not tainted
------------------------------------------------------
udevadm/312 is trying to acquire lock:
ffff80000aae1058 (udc_lock){+.+.}-{3:3}, at: usb_udc_uevent+0x54/0xe0
but task is already holding lock:
ffff000002277548 (kn->active#4){++++}-{0:0}, at: kernfs_seq_start+0x34/0xe0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (kn->active#4){++++}-{0:0}:
lock_acquire+0x68/0x84
__kernfs_remove+0x268/0x380
kernfs_remove_by_name_ns+0x58/0xac
sysfs_remove_file_ns+0x18/0x24
device_del+0x15c/0x440
-> #2 (device_links_lock){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
device_link_remove+0x3c/0xa0
_regulator_put.part.0+0x168/0x190
regulator_put+0x3c/0x54
devm_regulator_release+0x14/0x20
-> #1 (regulator_list_mutex){+.+.}-{3:3}:
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
regulator_lock_dependent+0x54/0x284
regulator_enable+0x34/0x80
phy_power_on+0x24/0x130
__dwc2_lowlevel_hw_enable+0x100/0x130
dwc2_lowlevel_hw_enable+0x18/0x40
dwc2_hsotg_udc_start+0x6c/0x2f0
gadget_bind_driver+0x124/0x1f4
-> #0 (udc_lock){+.+.}-{3:3}:
__lock_acquire+0x1298/0x20cc
lock_acquire.part.0+0xe0/0x230
lock_acquire+0x68/0x84
__mutex_lock+0x9c/0x430
mutex_lock_nested+0x38/0x64
usb_udc_uevent+0x54/0xe0
Evidently this was caused by the scope of udc_mutex being too large.
The mutex is only meant to protect udc->driver along with a few other
things. As far as I can tell, there's no reason for the mutex to be
held while the gadget core calls a gadget driver's ->bind or ->unbind
routine, or while a UDC is being started or stopped. (This accounts
for link #1 in the chain above, where the mutex is held while the
dwc2_hsotg_udc is started as part of driver probing.)
Gadget drivers' ->disconnect callbacks are problematic. Even though
usb_gadget_disconnect() will now acquire the udc_mutex, there's a
window in usb_gadget_bind_driver() between the times when the mutex is
released and the ->bind callback is invoked. If a disconnect occurred
during that window, we could call the driver's ->disconnect routine
before its ->bind routine. To prevent this from happening, it will be
necessary to prevent a UDC from connecting while it has no gadget
driver. This should be done already but it doesn't seem to be;
currently usb_gadget_connect() has no check for this. Such a check
will have to be added later.
Some degree of mutual exclusion is required in soft_connect_store(),
which can dereference udc->driver at arbitrary times since it is a
sysfs callback. The solution here is to acquire the gadget's device
lock rather than the udc_mutex. Since the driver core guarantees that
the device lock is always held during driver binding and unbinding,
this will make the accesses in soft_connect_store() mutually exclusive
with any changes to udc->driver.
Lastly, it turns out there is one place which should hold the
udc_mutex but currently does not: The function_show() routine needs
protection while it dereferences udc->driver. The missing lock and
unlock calls are added.
Link: https://lore.kernel.org/all/b2ba4245-9917-e399-94c8-03a383e7070e@samsung.com/
Fixes: 2191c00855 ("USB: gadget: Fix use-after-free Read in usb_udc_uevent()")
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable@vger.kernel.org
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YwkfhdxA/I2nOcK7@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On page 362 of the USB3.2 specification (
https://usb.org/sites/default/files/usb_32_20210125.zip),
The 'SuperSpeed Endpoint Companion Descriptor' shall only be returned
by Enhanced SuperSpeed devices that are operating at Gen X speed.
Each endpoint described in an interface is followed by a 'SuperSpeed
Endpoint Companion Descriptor'.
If users use SuperSpeed UDC, host can't recognize the device if endpoint
doesn't have 'SuperSpeed Endpoint Companion Descriptor' followed.
Currently in the uac2 driver code:
1. ss_epout_desc_comp follows ss_epout_desc;
2. ss_epin_fback_desc_comp follows ss_epin_fback_desc;
3. ss_epin_desc_comp follows ss_epin_desc;
4. Only ss_ep_int_desc endpoint doesn't have 'SuperSpeed Endpoint
Companion Descriptor' followed, so we should add it.
Fixes: eaf6cbe099 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jing Leng <jleng@ambarella.com>
Signed-off-by: Jack Pham <quic_jackp@quicinc.com>
Link: https://lore.kernel.org/r/20220721014815.14453-1-quic_jackp@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
