Include ADXL318 and ADXL319 accelerometers to the documentation.
The ADXL318 is based on the ADXL380, while the ADXL319 is based on the
ADXL382. However, the ADXL318/319 do not support some built-in features
like single tap, double tap and triple tap detection, and also activity
and inactivity detection.
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The pinout of all the supported chips in this binding have two interrupt
pins. Document the second one, too, even though the Linux driver
currently does not support the second interrupt. Boards may have it
wired nonetheless. While here, drop the dependency of interrupt-names
which is already described in the core.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set the interrupt type to rising edge within the example block in order
to match the new driver.
The entry that got replaced was not in use by the original driver.
Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Assert CPOL for a high-idle clock signal and CPHA for sampling on the
trailing (rising) edge.
Quoting from the datasheet:
"During the transitions on CSB, SCK must be high. SDI and SDO are driven
at the falling edge of SCK and should be captured at the rising edge of
SCK."
The sensor does not function with the default SPI clock mode.
Fixes: 7dbd479425 ("dt-bindings:iio:accel:bosch,bma220 device tree binding documentation")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add interrupt-names INT1 and INT2 for the two interrupt lines of the
sensor.
When one of the two interrupt lines is connected, the interrupt as its
interrupt-name, need to be declared in the devicetree. The driver then
configures the sensor to indicate its events on either INT1 or INT2.
If no interrupt is configured, then no interrupt-name should be
configured, and vice versa. In this case the sensor runs in FIFO BYPASS
mode. This allows sensor measurements, but none of the sensor events.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241225181338.69672-4-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull char / misc driver updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystem changes
for 6.12-rc1.
Lots of changes in here, primarily dominated by the usual IIO driver
updates and additions, but there are also small driver subsystem
updates all over the place. Included in here are:
- lots and lots of new IIO drivers and updates to existing ones
- interconnect subsystem updates and new drivers
- nvmem subsystem updates and new drivers
- mhi driver updates
- power supply subsystem updates
- kobj_type const work for many different small subsystems
- comedi driver fix
- coresight subsystem and driver updates
- fpga subsystem improvements
- slimbus fixups
- binder new feature addition for "frozen" notifications
- lots and lots of other small driver updates and cleanups
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (354 commits)
greybus: gb-beagleplay: Add firmware upload API
arm64: dts: ti: k3-am625-beagleplay: Add bootloader-backdoor-gpios to cc1352p7
dt-bindings: net: ti,cc1352p7: Add bootloader-backdoor-gpios
MAINTAINERS: Update path for U-Boot environment variables YAML
nvmem: layouts: add U-Boot env layout
comedi: ni_routing: tools: Check when the file could not be opened
ocxl: Remove the unused declarations in headr file
hpet: Fix the wrong format specifier
uio: Constify struct kobj_type
cxl: Constify struct kobj_type
binder: modify the comment for binder_proc_unlock
iio: adc: axp20x_adc: add support for AXP717 ADC
dt-bindings: iio: adc: Add AXP717 compatible
iio: adc: axp20x_adc: Add adc_en1 and adc_en2 to axp_data
w1: ds2482: Drop explicit initialization of struct i2c_device_id::driver_data to 0
tools: iio: rm .*.cmd when make clean
iio: adc: standardize on formatting for id match tables
iio: proximity: aw96103: Add support for aw96103/aw96105 proximity sensor
bus: mhi: host: pci_generic: Enable EDL trigger for Foxconn modems
bus: mhi: host: pci_generic: Update EDL firmware path for Foxconn modems
...
KX022A is a 3-axis Accelerometer from ROHM/Kionix. The sensor features
include variable ODRs, I2C and SPI control, FIFO/LIFO with watermark IRQ,
tap/motion detection, wake-up & back-to-sleep events, four acceleration
ranges (2, 4, 8 and 16g) and probably some other cool features.
Add the basic device tree description for the accelerometer. Only basic
accelerometer features are considered as of now - new properties may or
may not be needed in the future when rest of the features are supported.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/06f8e1ab29d02ed216db10091a269df4b6abad9a.1666614295.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of listing directly properties typical for SPI peripherals,
reference the spi-peripheral-props.yaml schema. This allows using all
properties typical for SPI-connected devices, even these which device
bindings author did not tried yet.
Remove the spi-* properties which now come via spi-peripheral-props.yaml
schema, except for the cases when device schema adds some constraints
like maximum frequency.
While changing additionalProperties->unevaluatedProperties, put it in
typical place, just before example DTS.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220816124321.67817-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADXL367 is an ultralow power, 3-axis MEMS accelerometer.
The ADXL367 does not alias input signals to achieve ultralow power
consumption, it samples the full bandwidth of the sensor at all
data rates. Measurement ranges of +-2g, +-4g, and +-8g are available,
with a resolution of 0.25mg/LSB on the +-2 g range.
In addition to its ultralow power consumption, the ADXL367
has many features to enable true system level power reduction.
It includes a deep multimode output FIFO, a built-in micropower
temperature sensor, and an internal ADC for synchronous conversion
of an additional analog input.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220214073810.781016-5-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
BMC156 is very smilar to BMC150, but it has only one accelerometer
interrupt pin. It would make sense if only INT1 was exposed but someone
at Bosch decided to only have an INT2 pin.
In this case, it does not make sense if the first interrupt pin is
treated as INT1 (since that pin does not exist). Add a note to the
bindings that the first interrupt pin is treated as INT2 for BMC156.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210802155657.102766-3-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In Linux the bma180 and bmc150-accel driver cover fairly similar chips
from Bosch (just with minor register differences). For the DT schema,
this does not make any difference: They both represent I2C/SPI devices,
have one or two interrupts plus a vdd/vddio-supply.
This means there is no need to duplicate the schema, we can just
document the compatibles for both drivers in a single DT schema.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210614163150.7774-4-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Bosch accelerometers similar to BMA255 are initially configured to
emit an active-high interrupt signal. This is currently not re-configured
in the bmc150-accel driver so the interrupt should most certainly be
IRQ_TYPE_EDGE_RISING (or potentially IRQ_TYPE_LEVEL_HIGH).
(Unless there is some kind of inverter installed on the board...)
At the moment the bmc150-accel driver forcefully requests the IRQ
using IRQF_TRIGGER_RISING, which means that the IRQ type is currently
ignored in all existing device trees.
Fixes: 6259551cf1 ("iio: accel: bmc150-accel: Add DT bindings")
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210614163150.7774-2-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
BMA253 has two interrupt pins (INT1 and INT2) that can be configured
independently. At the moment the bmc150-accel driver does not make use
of them but it might be able to in the future, so it's useful to already
specify all available interrupts in the device tree.
Set maxItems: 2 for interrupts to allow specifying a second one.
This is necessary as preparation to move the bosch,bma254 compatible
from bosch,bma180.yaml to bosch,bma255.yaml since bma180 allows two
interrupts, but BMA254 is better supported by the bmc150-accel driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-9-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The KX023-1025 accelerometer uses similar register bits as kxcjk1023,
so it can make use of the same driver. Document the new kionix,kx023-1025
compatible that is also supported by the kxcjk-1013 driver now.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add devicetree binding for the NXP FXLS8962AF/FXLS8964AF
accelerometer sensor.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
