Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan
Williams)
- Switch vmd from custom domain number allocator to the common
allocator to prevent a potential race with new non-VMD buses (Dan
Williams)
- Enable Precision Time Measurement (PTM) only if device advertises
support for a relevant role, to prevent invalid PTM Requests that
cause ACS violations that are reported as AER Uncorrectable
Non-Fatal errors (Mika Westerberg)
Resource management:
- Prevent resource tree corruption when BAR resize fails (Ilpo
Järvinen)
- Restore BARs to the original size if a BAR resize fails (Ilpo
Järvinen)
- Remove BAR release from BAR resize attempts by the xe, i915, and
amdgpu drivers so the PCI core can restore BARs if the resize fails
(Ilpo Järvinen)
- Move Resizable BAR code to rebar.c (Ilpo Järvinen)
- Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo
Järvinen)
- Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo
Järvinen)
Power management and error handling:
- For drivers using PCI legacy suspend, save config state at suspend
so that state (not any earlier state from enumeration, probe, or
error recovery) will be restored when resuming (Lukas Wunner)
- For devices with no driver or a driver that lacks power management,
save config state at hibernate so that state (not any earlier state
from enumeration, probe, or error recovery) will be restored when
resuming (Lukas Wunner)
- Save device config space on device addition, before driver binding,
so error recovery works more reliably (Lukas Wunner)
- Drop pci_save_state() from several drivers that no longer need it
since the PCI core always does it and pci_restore_state() no longer
invalidates the saved state (Lukas Wunner)
- Document use of pci_save_state() by drivers to capture the state
they want restored during error recovery (Lukas Wunner)
Power control:
- Add a struct pci_ops.assert_perst() function pointer to
assert/deassert PCIe PERST# and implement it for the qcom driver
(Krishna Chaitanya Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe
switch, which must be held in reset after poweron so the pwrctrl
driver can configure the switch via I2C before bringing up the
links (Krishna Chaitanya Chundru)
Endpoint framework:
- Convert the endpoint doorbell test to use a threaded IRQ to fix a
'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri)
- Add endpoint VNTB MSI doorbell support to reduce latency between
host and endpoint (Frank Li)
New native PCIe controller drivers:
- Add CIX Sky1 host controller DT binding and driver (Hans Zhang)
- Add NXP S32G host controller DT binding and driver (Vincent
Guittot)
- Add Renesas RZ/G3S host controller DT binding and driver (Claudiu
Beznea)
- Add SpacemiT K1 host controller DT binding and driver (Alex Elder)
Amlogic Meson PCIe controller driver:
- Update DT binding to name DBI region 'dbi', not 'elbi', and update
driver to support both (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Move struct pci_host_bridge allocation from pci_host_common_init()
to callers, which significantly simplifies pcie-apple (Marc
Zyngier)
Broadcom STB PCIe controller driver:
- Disable advertising ASPM L0s support correctly (Jim Quinlan)
- Add a panic/die handler to print diagnostic info in case PCIe
caused an unrecoverable abort (Jim Quinlan)
Cadence PCIe controller driver:
- Add module support for Cadence platform host and endpoint
controller driver (Manikandan K Pillai)
- Split headers into 'legacy' (LGA) and 'high perf' (HPA) to prepare
for new CIX Sky1 driver (Manikandan K Pillai)
MediaTek PCIe controller driver:
- Convert DT binding to YAML schema (Christian Marangi)
- Add Airoha AN7583 DT compatible and driver support (Christian
Marangi)
Qualcomm PCIe controller driver:
- Add Qualcomm Kaanapali to SM8550 DT binding (Qiang Yu)
- Add required 'power-domains' and 'resets' to qcom sa8775p, sc7280,
sc8280xp, sm8150, sm8250, sm8350, sm8450, sm8550, x1e80100 DT
schemas (Krzysztof Kozlowski)
- Look up OPP using both frequency and data rate (not just frequency)
so RPMh votes can account for both (Krishna Chaitanya Chundru)
Rockchip DesignWare PCIe controller driver:
- Add Rockchip RK3528 compatible strings in DT binding (Yao Zi)
STMicroelectronics STM32MP25 PCIe controller driver:
- Fix a race between link training and endpoint register
initialization (Christian Bruel)
- Align endpoint allocations to match the ATU requirements (Christian
Bruel)
Synopsys DesignWare PCIe controller driver:
- Clear L1 PM Substate Capability 'Supported' bits unless glue driver
says it's supported, which prevents users from enabling non-working
L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas)
- Remove now-superfluous L1SS disable code from tegra194 (Bjorn
Helgaas)
- Configure L1SS support in dw-rockchip when DT says
'supports-clkreq' (Shawn Lin)
TI Keystone PCIe controller driver:
- Fail the probe instead of silently succeeding if ks_pcie_of_data
didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli)
- Make keystone buildable as a loadable module, except on ARM32 where
hook_fault_code() is __init (Siddharth Vadapalli)"
* tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits)
MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer
MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer
PCI: sky1: Add PCIe host support for CIX Sky1
dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings
PCI: cadence: Add support for High Perf Architecture (HPA) controller
MAINTAINERS: Add NXP S32G PCIe controller driver maintainer
PCI: s32g: Add NXP S32G PCIe controller driver (RC)
PCI: dwc: Add register and bitfield definitions
dt-bindings: PCI: s32g: Add NXP S32G PCIe controller
PCI: Add Renesas RZ/G3S host controller driver
PCI: host-generic: Move bridge allocation outside of pci_host_common_init()
dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding
PCI: Validate pci_rebar_size_supported() input
Documentation: PCI: Amend error recovery doc with pci_save_state() rules
treewide: Drop pci_save_state() after pci_restore_state()
PCI/ERR: Ensure error recoverability at all times
PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw
PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths
PCI: dw-rockchip: Configure L1SS support
PCI: tegra194: Remove unnecessary L1SS disable code
...
- Add a struct pci_ops.assert_perst() function pointer to assert/deassert
PCIe PERST# and implement it for the qcom driver (Krishna Chaitanya
Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe switch,
which must be held in reset after poweron so the pwrctrl driver can
configure the switch via I2C before bringing up the links (Krishna
Chaitanya Chundru)
* pci/pwrctrl-tc9563:
PCI: pwrctrl: Add power control driver for TC9563
PCI: qcom: Implement .assert_perst()
PCI: dwc: Implement .assert_perst() for dwc glue drivers
PCI: Add .assert_perst() to control PCIe PERST#
dt-bindings: PCI: Add binding for Toshiba TC9563 PCIe switch
- Add module support for platform controller driver (Manikandan K Pillai)
- Split headers into 'legacy' (LGA) and 'high perf' (HPA) (Manikandan K
Pillai)
- Add DT binding and driver for CIX Sky1 (Hans Zhang)
* pci/controller/sky1:
MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer
PCI: sky1: Add PCIe host support for CIX Sky1
dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings
PCI: cadence: Add support for High Perf Architecture (HPA) controller
PCI: cadence: Move PCIe RP common functions to a separate file
PCI: cadence: Split PCIe controller header file
PCI: cadence: Add module support for platform controller driver
- Update DT binding to name DBI region "dbi", not "elbi", and update driver
to support both (Manivannan Sadhasivam)
* pci/controller/meson:
PCI: meson: Fix parsing the DBI register region
dt-bindings: PCI: amlogic: Fix the register name of the DBI region
- Convert DT binding to YAML schema (Christian Marangi)
- Add Airoha AN7583 DT compatible and driver support (Christian Marangi)
* pci/controller/mediatek:
PCI: mediatek: Add support for Airoha AN7583 SoC
PCI: mediatek: Use generic MACRO for TPVPERL delay
PCI: mediatek: Convert bool to single quirks entry and bitmap
dt-bindings: PCI: mediatek: Add support for Airoha AN7583
dt-bindings: PCI: mediatek: Convert to YAML schema
Binding incorrectly specifies the 'DBI' region as 'ELBI'. DBI is a must
have region for DWC controllers as it has the Root Port and controller
specific registers, while ELBI has optional registers.
Hence, fix the binding. Though this is an ABI break, this change is needed
to accurately describe the PCI memory map.
Fixes: 7cd2103911 ("dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20251101-pci-meson-fix-v1-1-c50dcc56ed6a@oss.qualcomm.com
The amlogic,axg-pcie binding was never enabled as the 'select' schema
expects a single compatible value, but the binding has a fallback
compatible. Fix the 'select' by adding a 'contains'. With this, several
errors in the clock and reset properties are exposed. Some of the names
aren't defined in the common DWC schema and the order of clocks entries
doesn't match .dts files.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20251024011122.26001-1-robh@kernel.org
Convert the PCI mediatek Documentation to YAML schema to enable
validation of the supported GEN1/2 Mediatek PCIe controller.
While converting, lots of cleanup were done from the .txt with better
specifying what is supported by the various PCIe controller variant and
drop of redundant info that are part of the standard PCIe Host Bridge
schema.
To reduce schema complexity the .txt is split in 2 YAML, one for
mt7623/mt2701 and the other for every other compatible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20251020111121.31779-2-ansuelsmth@gmail.com
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Add PCI_FIND_NEXT_CAP() and PCI_FIND_NEXT_EXT_CAP() macros that
take config space accessor functions.
Implement pci_find_capability(), pci_find_ext_capability(), and
dwc, dwc endpoint, and cadence capability search interfaces with
them (Hans Zhang)
- Leave parent unit address 0 in 'interrupt-map' so that when we
build devicetree nodes to describe PCI functions that contain
multiple peripherals, we can build this property even when
interrupt controllers lack 'reg' properties (Lorenzo Pieralisi)
- Add a Xeon 6 quirk to disable Extended Tags and limit Max Read
Request Size to 128B to avoid a performance issue (Ilpo Järvinen)
- Add sysfs 'serial_number' file to expose the Device Serial Number
(Matthew Wood)
- Fix pci_acpi_preserve_config() memory leak (Nirmoy Das)
Resource management:
- Align m68k pcibios_enable_device() with other arches (Ilpo
Järvinen)
- Remove sparc pcibios_enable_device() implementations that don't do
anything beyond what pci_enable_resources() does (Ilpo Järvinen)
- Remove mips pcibios_enable_resources() and use
pci_enable_resources() instead (Ilpo Järvinen)
- Clean up bridge window sizing and assignment (Ilpo Järvinen),
including:
- Leave non-claimed bridge windows disabled
- Enable bridges even if a window wasn't assigned because not all
windows are required by downstream devices
- Preserve bridge window type when releasing the resource, since
the type is needed for reassignment
- Consolidate selection of bridge windows into two new
interfaces, pbus_select_window() and
pbus_select_window_for_type(), so this is done consistently
- Compute bridge window start and end earlier to avoid logging
stale information
MSI:
- Add quirk to disable MSI on RDC PCI to PCIe bridges (Marcos Del Sol
Vives)
Error handling:
- Align AER with EEH by allowing drivers to request a Bus Reset on
Non-Fatal Errors (in addition to the reset on Fatal Errors that we
already do) (Lukas Wunner)
- If error recovery fails, emit FAILED_RECOVERY uevents for the
devices, not for the bridge leading to them.
This makes them correspond to BEGIN_RECOVERY uevents (Lukas Wunner)
- Align AER with EEH by calling err_handler.error_detected()
callbacks to notify drivers if error recovery fails (Lukas Wunner)
- Align AER with EEH by restoring device error_state to
pci_channel_io_normal before the err_handler.slot_reset() callback.
This is earlier than before the err_handler.resume() callback
(Lukas Wunner)
- Emit a BEGIN_RECOVERY uevent when driver's
err_handler.error_detected() requests a reset, as well as when it
says recovery is complete or can be done without a reset (Niklas
Schnelle)
- Align s390 with AER and EEH by emitting uevents during error
recovery (Niklas Schnelle)
- Align EEH with AER and s390 by emitting BEGIN_RECOVERY,
SUCCESSFUL_RECOVERY, or FAILED_RECOVERY uevents depending on the
result of err_handler.error_detected() (Niklas Schnelle)
- Fix a NULL pointer dereference in aer_ratelimit() when ACPI GHES
error information identifies a device without an AER Capability
(Breno Leitao)
- Update error decoding and TLP Log printing for new errors in
current PCIe base spec (Lukas Wunner)
- Update error recovery documentation to match the current code
and use consistent nomenclature (Lukas Wunner)
ASPM:
- Enable all ClockPM and ASPM states for devicetree platforms, since
there's typically no firmware that enables ASPM
This is a risky change that may uncover hardware or configuration
defects at boot-time rather than when users enable ASPM via sysfs
later. Booting with "pcie_aspm=off" prevents this enabling
(Manivannan Sadhasivam)
- Remove the qcom code that enabled ASPM (Manivannan Sadhasivam)
Power management:
- If a device has already been disconnected, e.g., by a hotplug
removal, don't bother trying to resume it to D0 when detaching the
driver.
This avoids annoying "Unable to change power state from D3cold to
D0" messages (Mario Limonciello)
- Ensure devices are powered up before config reads for
'max_link_width', 'current_link_speed', 'current_link_width',
'secondary_bus_number', and 'subordinate_bus_number' sysfs files.
This prevents using invalid data (~0) in drivers or lspci and,
depending on how the PCIe controller reports errors, may avoid
error interrupts or crashes (Brian Norris)
Virtualization:
- Add rescan/remove locking when enabling/disabling SR-IOV, which
avoids list corruption on s390, where disabling SR-IOV also
generates hotplug events (Niklas Schnelle)
Peer-to-peer DMA:
- Free struct p2p_pgmap, not a member within it, in the
pci_p2pdma_add_resource() error path (Sungho Kim)
Endpoint framework:
- Document sysfs interface for BAR assignment of vNTB endpoint
functions (Jerome Brunet)
- Fix array underflow in endpoint BAR test case (Dan Carpenter)
- Skip endpoint IRQ test if the IRQ is out of range to avoid false
errors (Christian Bruel)
- Fix endpoint test case for controllers with fixed-size BARs smaller
than requested by the test (Marek Vasut)
- Restore inbound translation when disabling doorbell so the endpoint
doorbell test case can be run more than once (Niklas Cassel)
- Avoid a NULL pointer dereference when releasing DMA channels in
endpoint DMA test case (Shin'ichiro Kawasaki)
- Convert tegra194 interrupt number to MSI vector to fix endpoint
Kselftest MSI_TEST test case (Niklas Cassel)
- Reset tegra194 BARs when running in endpoint mode so the BAR tests
don't overwrite the ATU settings in BAR4 (Niklas Cassel)
- Handle errors in tegra194 BPMP transactions so we don't mistakenly
skip future PERST# assertion (Vidya Sagar)
AMD MDB PCIe controller driver:
- Update DT binding example to separate PERST# to a Root Port stanza
to make multiple Root Ports possible in the future (Sai Krishna
Musham)
- Add driver support for PERST# being described in a Root Port
stanza, falling back to the host bridge if not found there (Sai
Krishna Musham)
Freescale i.MX6 PCIe controller driver:
- Enable the 3.3V Vaux supply if available so devices can request
wakeup with either Beacon or WAKE# (Richard Zhu)
MediaTek PCIe Gen3 controller driver:
- Add optional sys clock ready time setting to avoid sys_clk_rdy
signal glitching in MT6991 and MT8196 (AngeloGioacchino Del Regno)
- Add DT binding and driver support for MT6991 and MT8196
(AngeloGioacchino Del Regno)
NVIDIA Tegra PCIe controller driver:
- When asserting PERST#, disable the controller instead of mistakenly
disabling the PLL twice (Nagarjuna Kristam)
- Convert struct tegra_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
Qualcomm PCIe controller driver:
- Select PCI Power Control Slot driver so slot voltage rails can be
turned on/off if described in Root Port devicetree node (Qiang Yu)
- Parse only PCI bridge child nodes in devicetree, skipping unrelated
nodes such as OPP (Operating Performance Points), which caused
probe failures (Krishna Chaitanya Chundru)
- Add 8.0 GT/s and 32.0 GT/s equalization settings (Ziyue Zhang)
- Consolidate Root Port 'phy' and 'reset' properties in struct
qcom_pcie_port, regardless of whether we got them from the Root
Port node or the host bridge node (Manivannan Sadhasivam)
- Fetch and map the ELBI register space in the DWC core rather than
in each driver individually (Krishna Chaitanya Chundru)
- Enable ECAM mechanism in DWC core by setting up iATU with 'CFG
Shift Feature' and use this in the qcom driver (Krishna Chaitanya
Chundru)
- Add SM8750 compatible to qcom,pcie-sm8550.yaml (Krishna Chaitanya
Chundru)
- Update qcom,pcie-x1e80100.yaml to allow fifth PCIe host on Qualcomm
Glymur, which is compatible with X1E80100 but doesn't have the
cnoc_sf_axi clock (Qiang Yu)
Renesas R-Car PCIe controller driver:
- Fix a typo that prevented correct PHY initialization (Marek Vasut)
- Add a missing 1ms delay after PWR reset assertion as required by
the V4H manual (Marek Vasut)
- Assure reset has completed before DBI access to avoid SError (Marek
Vasut)
- Fix inverted PHY initialization check, which sometimes led to
timeouts and failure to start the controller (Marek Vasut)
- Pass the correct IRQ domain to generic_handle_domain_irq() to fix a
regression when converting to msi_create_parent_irq_domain()
(Claudiu Beznea)
- Drop the spinlock protecting the PMSR register - it's no longer
required since pci_lock already serializes accesses (Marek Vasut)
- Convert struct rcar_msi mask_lock to raw spinlock to avoid a lock
nesting error (Marek Vasut)
SOPHGO PCIe controller driver:
- Check for existence of struct cdns_pcie.ops before using it to
allow Cadence drivers that don't need to supply ops (Chen Wang)
- Add DT binding and driver for the SOPHGO SG2042 PCIe controller
(Chen Wang)
STMicroelectronics STM32MP25 PCIe controller driver:
- Update pinctrl documentation of initial states and use in runtime
suspend/resume (Christian Bruel)
- Add pinctrl_pm_select_init_state() for use by stm32 driver, which
needs it during resume (Christian Bruel)
- Add devicetree bindings and drivers for the STMicroelectronics
STM32MP25 in host and endpoint modes (Christian Bruel)
Synopsys DesignWare PCIe controller driver:
- Add support for x16 in devicetree 'num-lanes' property (Konrad
Dybcio)
- Verify that if DT specifies a single IRQ for all eDMA channels, it
is named 'dma' (Niklas Cassel)
TI J721E PCIe driver:
- Add MODULE_DEVICE_TABLE() so driver can be autoloaded (Siddharth
Vadapalli)
- Power controller off before configuring the glue layer so the
controller latches the correct values on power-on (Siddharth
Vadapalli)
TI Keystone PCIe controller driver:
- Use devm_request_irq() so 'ks-pcie-error-irq' is freed when driver
exits with error (Siddharth Vadapalli)
- Add Peripheral Virtualization Unit (PVU), which restricts DMA from
PCIe devices to specific regions of host memory, to the ti,am65
binding (Jan Kiszka)
Xilinx NWL PCIe controller driver:
- Clear bootloader E_ECAM_CONTROL before merging in the new driver
value to avoid writing invalid values (Jani Nurminen)"
* tag 'pci-v6.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (141 commits)
PCI/AER: Avoid NULL pointer dereference in aer_ratelimit()
MAINTAINERS: Add entry for ST STM32MP25 PCIe drivers
PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
PCI: stm32: Add PCIe host support for STM32MP25
PCI: xilinx-nwl: Fix ECAM programming
PCI: j721e: Fix incorrect error message in probe()
PCI: keystone: Use devm_request_irq() to free "ks-pcie-error-irq" on exit
dt-bindings: PCI: qcom,pcie-x1e80100: Set clocks minItems for the fifth Glymur PCIe Controller
PCI: dwc: Support 16-lane operation
PCI: Add lockdep assertion in pci_stop_and_remove_bus_device()
PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV
PCI: rcar-host: Convert struct rcar_msi mask_lock into raw spinlock
PCI: tegra194: Rename 'root_bus' to 'root_port_bus' in tegra_pcie_downstream_dev_to_D0()
PCI: tegra: Convert struct tegra_msi mask_lock into raw spinlock
PCI: rcar-gen4: Fix inverted break condition in PHY initialization
PCI: rcar-gen4: Assure reset occurs before DBI access
PCI: rcar-gen4: Add missing 1ms delay after PWR reset assertion
PCI: Set up bridge resources earlier
PCI: rcar-host: Drop PMSR spinlock
...
- Update pinctrl documentation of initial states and use in runtime
suspend/resume (Christian Bruel)
- Add pinctrl_pm_select_init_state() for use by stm32 driver, which needs
it during resume (Christian Bruel)
- Add devicetree bindings and drivers for the STMicroelectronics STM32MP25
in host and endpoint modes (Christian Bruel)
* pci/controller/stm32:
MAINTAINERS: Add entry for ST STM32MP25 PCIe drivers
PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Endpoint bindings
PCI: stm32: Add PCIe host support for STM32MP25
dt-bindings: PCI: Add STM32MP25 PCIe Root Complex bindings
pinctrl: Add pinctrl_pm_select_init_state helper function
Documentation: pinctrl: Describe PM helper functions for standard states.
- Check for existence of struct cdns_pcie.ops before using it to allow
Cadence drivers that don't need to supply ops (Chen Wang)
- Add DT binding and driver for the Sophgo SG2042 PCIe controller (Chen
Wang)
* pci/controller/sophgo:
PCI: sg2042: Add Sophgo SG2042 PCIe driver
PCI: cadence: Check for the existence of cdns_pcie::ops before using it
dt-bindings: pci: Add Sophgo SG2042 PCIe host
- Add optional sys clock ready time setting to avoid sys_clk_rdy signal
glitching in MT6991 and MT8196 (AngeloGioacchino Del Regno)
- Add DT binding and driver support for MT6991 and MT8196 (AngeloGioacchino
Del Regno)
* pci/controller/mediatek-gen3:
PCI: mediatek-gen3: Add support for MediaTek MT8196 SoC
dt-bindings: PCI: mediatek-gen3: Add support for MT6991/MT8196
PCI: mediatek-gen3: Implement sys clock ready time setting
- Update DT binding example to separate PERST# to a Root Port stanza to
make multiple Root Ports possible in the future (Sai Krishna Musham)
- Add driver support for Root Port PERST# (Sai Krishna Musham)
* pci/controller/amd-mdb:
PCI: amd-mdb: Add support for PCIe RP PERST# signal handling
dt-bindings: PCI: amd-mdb: Add example usage of reset-gpios for PCIe RP PERST#
The Peripheral Virtualization Unit (PVU) on the AM65 SoC is capable of
restricting DMA from PCIe devices to specific regions of host memory.
Add the optional property "memory-regions" to point to such regions of
memory when PVU is used.
Since the PVU deals with system physical addresses, utilizing the PVU
with PCIe devices also requires setting up the VMAP registers to map the
Requester ID of the PCIe device to the CBA Virtual ID, which in turn is
mapped to the system physical address. Hence, describe the VMAP
registers which are optional unless the PVU shall be used for PCIe.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
[mani: Expanded PVU in description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250728023701.116963-3-huaqian.li@siemens.com
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Allow built-in drivers, not just modular drivers, to use async
initial probing (Lukas Wunner)
- Support Immediate Readiness even on devices with no PM Capability
(Sean Christopherson)
- Consolidate definition of PCIE_RESET_CONFIG_WAIT_MS (100ms), the
required delay between a reset and sending config requests to a
device (Niklas Cassel)
- Add pci_is_display() to check for "Display" base class and use it
in ALSA hda, vfio, vga_switcheroo, vt-d (Mario Limonciello)
- Allow 'isolated PCI functions' (multi-function devices without a
function 0) for LoongArch, similar to s390 and jailhouse (Huacai
Chen)
Power control:
- Add ability to enable optional slot clock for cases where the PCIe
host controller and the slot are supplied by different clocks
(Marek Vasut)
PCIe native device hotplug:
- Fix runtime PM ref imbalance on Hot-Plug Capable ports caused by
misinterpreting a config read failure after a device has been
removed (Lukas Wunner)
- Avoid creating a useless PCIe port service device for pciehp if the
slot is handled by the ACPI hotplug driver (Lukas Wunner)
- Ignore ACPI hotplug slots when calculating depth of pciehp hotplug
ports (Lukas Wunner)
Virtualization:
- Save VF resizable BAR state and restore it after reset (Michał
Winiarski)
- Allow IOV resources (VF BARs) to be resized (Michał Winiarski)
- Add pci_iov_vf_bar_set_size() so drivers can control VF BAR size
(Michał Winiarski)
Endpoint framework:
- Add RC-to-EP doorbell support using platform MSI controller,
including a test case (Frank Li)
- Allow BAR assignment via configfs so platforms have flexibility in
determining BAR usage (Jerome Brunet)
Native PCIe controller drivers:
- Convert amazon,al-alpine-v[23]-pcie, apm,xgene-pcie,
axis,artpec6-pcie, marvell,armada-3700-pcie, st,spear1340-pcie to
DT schema format (Rob Herring)
- Use dev_fwnode() instead of of_fwnode_handle() to remove OF
dependency in altera (fixes an unused variable), designware-host,
mediatek, mediatek-gen3, mobiveil, plda, xilinx, xilinx-dma,
xilinx-nwl (Jiri Slaby, Arnd Bergmann)
- Convert aardvark, altera, brcmstb, designware-host, iproc,
mediatek, mediatek-gen3, mobiveil, plda, rcar-host, vmd, xilinx,
xilinx-dma, xilinx-nwl from using pci_msi_create_irq_domain() to
using msi_create_parent_irq_domain() instead; this makes the
interrupt controller per-PCI device, allows dynamic allocation of
vectors after initialization, and allows support of IMS (Nam Cao)
APM X-Gene PCIe controller driver:
- Rewrite MSI handling to MSI CPU affinity, drop useless CPU hotplug
bits, use device-managed memory allocations, and clean things up
(Marc Zyngier)
- Probe xgene-msi as a standard platform driver rather than a
subsys_initcall (Marc Zyngier)
Broadcom STB PCIe controller driver:
- Add optional DT 'num-lanes' property and if present, use it to
override the Maximum Link Width advertised in Link Capabilities
(Jim Quinlan)
Cadence PCIe controller driver:
- Use PCIe Message routing types from the PCI core rather than
defining private ones (Hans Zhang)
Freescale i.MX6 PCIe controller driver:
- Add IMX8MQ_EP third 64-bit BAR in epc_features (Richard Zhu)
- Add IMX8MM_EP and IMX8MP_EP fixed 256-byte BAR 4 in epc_features
(Richard Zhu)
- Configure LUT for MSI/IOMMU in Endpoint mode so Root Complex can
trigger doorbel on Endpoint (Frank Li)
- Remove apps_reset (LTSSM_EN) from
imx_pcie_{assert,deassert}_core_reset(), which fixes a hotplug
regression on i.MX8MM (Richard Zhu)
- Delay Endpoint link start until configfs 'start' written (Richard
Zhu)
Intel VMD host bridge driver:
- Add Intel Panther Lake (PTL)-H/P/U Vendor ID (George D Sworo)
Qualcomm PCIe controller driver:
- Add DT binding and driver support for SA8255p, which supports ECAM
for Configuration Space access (Mayank Rana)
- Update DT binding and driver to describe PHYs and per-Root Port
resets in a Root Port stanza and deprecate describing them in the
host bridge; this makes it possible to support multiple Root Ports
in the future (Krishna Chaitanya Chundru)
- Add Qualcomm QCS615 to SM8150 DT binding (Ziyue Zhang)
- Add Qualcomm QCS8300 to SA8775p DT binding (Ziyue Zhang)
- Drop TBU and ref clocks from Qualcomm SM8150 and SC8180x DT
bindings (Konrad Dybcio)
- Document 'link_down' reset in Qualcomm SA8775P DT binding (Ziyue
Zhang)
- Add required PCIE_RESET_CONFIG_WAIT_MS delay after Link up IRQ
(Niklas Cassel)
Rockchip PCIe controller driver:
- Drop unused PCIe Message routing and code definitions (Hans Zhang)
- Remove several unused header includes (Hans Zhang)
- Use standard PCIe config register definitions instead of
rockchip-specific redefinitions (Geraldo Nascimento)
- Set Target Link Speed to 5.0 GT/s before retraining so we have a
chance to train at a higher speed (Geraldo Nascimento)
Rockchip DesignWare PCIe controller driver:
- Prevent race between link training and register update via DBI by
inhibiting link training after hot reset and link down (Wilfred
Mallawa)
- Add required PCIE_RESET_CONFIG_WAIT_MS delay after Link up IRQ
(Niklas Cassel)
Sophgo PCIe controller driver:
- Add DT binding and driver for Sophgo SG2044 PCIe controller driver
in Root Complex mode (Inochi Amaoto)
Synopsys DesignWare PCIe controller driver:
- Add required PCIE_RESET_CONFIG_WAIT_MS after waiting for Link up on
Ports that support > 5.0 GT/s. Slower Ports still rely on the
not-quite-correct PCIE_LINK_WAIT_SLEEP_MS 90ms default delay while
waiting for the Link (Niklas Cassel)"
* tag 'pci-v6.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (116 commits)
dt-bindings: PCI: qcom,pcie-sa8775p: Document 'link_down' reset
dt-bindings: PCI: Remove 83xx-512x-pci.txt
dt-bindings: PCI: Convert amazon,al-alpine-v[23]-pcie to DT schema
dt-bindings: PCI: Convert marvell,armada-3700-pcie to DT schema
dt-bindings: PCI: Convert apm,xgene-pcie to DT schema
dt-bindings: PCI: Convert axis,artpec6-pcie to DT schema
dt-bindings: PCI: Convert st,spear1340-pcie to DT schema
PCI: Move is_pciehp check out of pciehp_is_native()
PCI: pciehp: Use is_pciehp instead of is_hotplug_bridge
PCI/portdrv: Use is_pciehp instead of is_hotplug_bridge
PCI/ACPI: Fix runtime PM ref imbalance on Hot-Plug Capable ports
selftests: pci_endpoint: Add doorbell test case
misc: pci_endpoint_test: Add doorbell test case
PCI: endpoint: pci-epf-test: Add doorbell test support
PCI: endpoint: Add pci_epf_align_inbound_addr() helper for inbound address alignment
PCI: endpoint: pci-ep-msi: Add checks for MSI parent and mutability
PCI: endpoint: Add RC-to-EP doorbell support using platform MSI controller
PCI: dwc: Add Sophgo SG2044 PCIe controller driver in Root Complex mode
PCI: vmd: Switch to msi_create_parent_irq_domain()
PCI: vmd: Convert to lock guards
...
- Export DWC MSI controller related APIs for use by upcoming DWC-based ECAM
implementation (Mayank Rana)
- Rename gen_pci_init() to pci_host_common_ecam_create() and export for use
by controller drivers (Mayank Rana)
- Add DT binding and driver support for SA8255p, which supports ECAM for
Configuration Space access (Mayank Rana)
- Update DT binding and driver to describe PHYs and per-Root Port resets in
a Root Port stanza and deprecate describing them in the host bridge; this
makes it possible to support multiple Root Ports in the future (Krishna
Chaitanya Chundru)
* pci/controller/qcom:
PCI: qcom: Add support for parsing the new Root Port binding
dt-bindings: PCI: qcom: Move PHY & reset GPIO to Root Port node
PCI: qcom: Add support for Qualcomm SA8255p based PCIe Root Complex
dt-bindings: PCI: qcom,pcie-sa8255p: Document ECAM compliant PCIe root complex
PCI: host-generic: Rename and export gen_pci_init() for PCIe controller drivers
PCI: dwc: Export DWC MSI controller related APIs
- Add optional DT 'num-lanes' property and if present, use it to override
the Maximum Link Width advertised in Link Capabilities (Jim Quinlan)
* pci/controller/brcmstb:
PCI: brcmstb: Replace open coded value with PCIE_T_RRS_READY_MS
MAINTAINERS: Drop Nicolas from maintaining pcie-brcmstb
PCI: brcmstb: Set MLW based on "num-lanes" DT property if present
dt-bindings: PCI: brcm,stb-pcie: Add num-lanes property
