[Why]
When a monitor is booting it's possible that it isn't ready to retrieve
link caps and this can lead to an EDID read failure:
```
[drm:retrieve_link_cap [amdgpu]] *ERROR* retrieve_link_cap: Read receiver caps dpcd data failed.
amdgpu 0000:c5:00.0: [drm] *ERROR* No EDID read.
```
[How]
Rather than msleep once and try a few times, msleep each time. Should
be no changes for existing working monitors, but should correct reading
caps on a monitor that is slow to boot.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4672
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
1.Add flow to enable and configure panel replay enablement and
configuration
2.Add registry key for enable option
3.Add replay version check to be compatible with freesync replay
4.Add AC/DC switch function to notify ac/dc change.
5.Add flow in set event function to check and decide Replay
enable/disable
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Jack Chang <jack.chang@amd.com>
Signed-off-by: Leon Huang <Leon.Huang1@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some mst branches NAK's segment pointer writes with mot disabled.
So reset of segment pointer to 0 should be performed with mot enabled.
[How]
Write segment pointer of mst branch devices with mot enabled.
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Driver only process hpd irq when a branch device or when
the link is established. It would cause some irq for bw_alloc
mode of dp tunneling are ignored.
[HOW]
Driver should process hpd irq if bw_alloc and dp tunneling
are enabled.
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When bw allocation mode enabled, dpia may reports lttpr cap with
reduced common cap. It would cause driver not start pre-training with
max available bandwidth.
[How]
When bw allocation mode enabled, use NRD cap as lttpr cap.
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
According to the vendor’s requirement, after each OUI write,
the PSR cap must be read; otherwise, the vendor will default
to using PSRSU. But its PSR cap indicates that it only supports
PSR1.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Paul Hsieh <Paul.Hsieh@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Header file name "link.h" collides with system header when dc is
compiled as a user-mode library
[WHAT]
Rename link.h to link_service.h to avoid name collision
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Currently fallback to low link rate if the link training
fails once on USB4. It may cause the bandwidth couldn't
satisfy the requirement of streams. Modify the policy
to do training retry in the previous few times, only
do fallback at the last time.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust whitespace around operators to improve code readability
and comply with kernel coding style guidelines.
These changes are purely stylistic and introduce no
functional modifications.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In the worst case, AUX intra-hop done can take hundreds of milliseconds as
each retimer in a link might have to wait a full AUX_RD_INTERVAL to send
LT abort downstream.
[HOW]
Wait 300ms for each retimer in a link to allow time to propagate a LT abort
without infinitely waiting on intra-hop done.
For no-retimer case, keep the max duration at 10ms.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SmartMux is a mechanism to switch the GPU being used for scanout in a
hybrid configuration. This is used for devices with an eDP and two GPUs.
This is only valid when the system has a physical switch (Multiplexer)
in the board to switch between the two GPUs.
When a graphically intensive workload like a game is being run, the
system can be switch the active display to the dGPU, so that we can
avoid copying the buffer from dGPU to APU for scanout. This helps with
latency and FPS. When power consumption is preferred, the system can be
switched to the APU.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
UHBR link rate capable eDPs will use HPO for encoding. Need to pass
HPO stream and link encoder instances to DMCUB for Replay FSM to
know which instances to use.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The tunnel BW validation code has changed to the new one.
Remove the unused code.
The DP tunneling overhead is not updated in SST.
Move updating DP tunneling overhead for both SST and MST.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These fields are read for the explicit purpose of detecting embedded LTTPRs
(i.e. between host ASIC and the user-facing port), and thus need to
calculate the correct DPCD address offset based on LTTPR count to target
the appropriate LTTPR's DPCD register space with these queries.
[HOW]
Cascaded LTTPRs in a link each snoop and increment LTTPR count when queried
via DPCD read, so an LTTPR embedded in a source device (e.g. USB4 port on a
laptop) will always be addressible using the max LTTPR count seen by the
host. Therefore we simply need to use a recently added helper function to
calculate the correct DPCD address to target potentially embedded LTTPRs
based on the received LTTPR count.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Nits programming for SDR panel is only supported by VESA ABC.
[How]
1. Loose nits programming for OLED SDR panel with AMD ABC.
2. We support two ABC methods. Disable one before we program the other
in case panel freaks out.
3. Update HDR judgement in setBR with a solider condition.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Early EQ pattern sequence is required for some LTTPR + old dongle
combinations.
[HOW]
If DP_EARLY_8B10B_TPS2 chip cap is set, this new sequence programs phy
to output TPS2 before initiating link training and writes TPS1 to
LTTPR training pattern register as instructed by vendor.
Add function to get embedded LTTPR target address offset.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: TungYu Lu <tungyu.lu@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
LTTPR are required to program DPCD 0000Eh to 0x4 (16ms) upon AUX read
reply to this register. Since old Sinks witih DPCD rev 1.1 and earlier
may not support this register, assume the mandatory value is programmed
by the LTTPR to avoid AUX timeout issues.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN4+ supports a new register based mailbox for sending messages
from host to DMCUB. This mailbox supports 64 byte commands, which makes
it compatible with the same structure as the frame buffer based mailbox.
[HOW]
The intention for reg_inbox0 is to be slot in replacement for the frame
buffer based mailbox (Inbox1). It supports all of the required features:
- Supports all messages handled by FB Inbox1
- Supports multi command batching
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Replay need special policy for the scenario Teams,
add a flag to imply apply special policy or not.
[How]
Add a config option intended for future use for video conferencing applications.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: ChunTao Tso <ChunTao.Tso@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The response of DP BW allocation is handled in Outbox ISR.
When it failed to request the DP BW allocation, it sent another
DPCD request in Outbox ISR immediately. The DP AUX reply also
uses the Outbox ISR. So, no AUX reply happened in this case.
Change to use HPD IRQ for the notification.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN4+ supports a new register based mailbox for sending messages
from host to DMCUB. This mailbox supports 64 byte commands, which makes
it compatible with the same structure as the frame buffer based mailbox.
[HOW]
The intention for reg_inbox0 is to be slot in replacement for the frame
buffer based mailbox (Inbox1). It supports all of the required features:
- Supports all messages handled by FB Inbox1
- Supports multi command batching
Reviewed-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
DP spec has been updated recently to make regulated autonomous mode more
well-defined. In case any PCON vendors choose to implement regulated
autonomous mode in the future, pre-emptively add handling for the
regulated autonomous mode based on current spec.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
USB4 DP BW Allocation uses DP_TUNNELING_IRQ to indicate the status update.
The DP_TUNNELING_IRQ is defined in LINK_SERVICE_IRQ_VECTOR_ESI0. When
receiving DP HPD IRQ in USB4, read the LINK_SERVICE_IRQ_VECTOR_ESI0.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Certain PCON will clear the FRL_MODE bit despite supporting the link BW
indicated in the other bits.
Thus, skip checking the FRL_MODE bit when interpreting the
hdmi_encoded_link_bw struct.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These are left required changes for dio encoder refactor.
[HOW]
1. original logic is separated by config option
2. new link encoder dp enable/disable code for dcn35
3. process fec only for DP 8b10b encoding
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
