The BIOS uses this register to write the results of the
DAC_LoadDetection command, so we'll need to read this
in order to make DAC load detection work.
As a reference, I used the mmBIOS_SCRATCH_0 definition from
the amdgpu legacy display code.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We support two kinds of analog connections:
1. DVI-I, which allows both digital and analog signals:
The DC code base only allows 1 encoder per connector, and the
preferred engine type is still going to be digital. So, for DVI-I
to work, we need to make sure the pre-existing link encoder can
also work with analog signals.
1. VGA, which only supports analog signals:
For VGA, we need to create a link encoder that only works with the
DAC without perturbing any digital transmitter functionality.
Since dce110_link_encoder already supports analog DVI-I,
just reuse that code for VGA as well.
v2:
Reduce code churn by reusing same link encoder for VGA and DVI-I.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add analog stream encoders for DCE which will be used when
connecting an analog display through VGA or DVI-I.
Considering that all stream encoder functions currently deal
with digital streams, there is nothing for an analog stream
encoder to do, making them basically a no-op.
That being said, we still need some kind of stream encoder to
represent an analog stream, and it is beneficial to split them
from digital stream encoders in the code to make sure they
don't accidentally write any DIG* registers.
On supported chips there is currently up to 1 analog encoder,
which is DACA. There are references to DACB in some code such
as VBIOS commands and register files but it seems to be
not present on DCE 6 and newer.
Set num_analog_stream_encoder = 1 so that we can support
the analog connectors on DCE 6-10, for now.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Scaling doesn't work on DCE6 at the moment, the current
register programming produces incorrect output when using
fractional scaling (between 100-200%) on resolutions higher
than 1080p.
Disable it until we figure out how to program it properly.
Fixes: 7c15fd86aa ("drm/amd/display: dc/dce: add initial DCE6 support (v10)")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dce100_validate_global function was verbatim exactly the
same as dce60_validate_global and dce80_validate_global.
Share dce100_validate_global between DCE6-10 to save code size.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCE6-8 have very similar capabilities to DCE10, they support the
same DP and HDMI versions and work similarly.
Share dce100_validate_bandwidth between DCE6-10 to reduce code
duplication in the DC driver.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reject modes with a pixel clock higher than the maximum display
clock. Use 400 MHz as a fallback value when the maximum display
clock is not known. Pixel clocks that are higher than the display
clock just won't work and are not supported.
With the addition of the YUV422 fallback, DC can now accidentally
select a mode requiring higher pixel clock than actually supported
when the DP version supports the required bandwidth but the clock
is otherwise too high for the display engine. DCE 6-10 don't
support these modes but they don't have a bandwidth calculation
to reject them properly.
Fixes: db291ed173 ("drm/amd/display: Add fallback path for YCBCR422")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC can turn off the display clock when no displays are connected
or when all displays are off, for reference see:
- dce*_validate_bandwidth
DC also assumes that the DP clock is always on and never powers
it down, for reference see:
- dce110_clock_source_power_down
In case of DCE 6.0 and 6.4, PLL0 is the clock source for both
the engine clock and DP clock, for reference see:
- radeon_atom_pick_pll
- atombios_crtc_set_disp_eng_pll
Therefore, PLL0 should be always kept running on DCE 6.0 and 6.4.
This commit achieves that by ensuring that by setting the display
clock to the corresponding value in low power state instead of
zero.
This fixes a page flip timeout on SI with DC which happens when
all connected displays are blanked.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Apparently, both DCE 6.0 and 6.4 have 3 PLLs, but PLL0 can only
be used for DP. Make sure to initialize the correct amount of PLLs
in DC for these DCE versions and use PLL0 only for DP.
Also, on DCE 6.0 and 6.4, the PLL0 needs to be powered on at
initialization as opposed to DCE 6.1 and 7.x which use a different
clock source for DFS.
The following functions were used as reference from the old
radeon driver implementation of DCE 6.x:
- radeon_atom_pick_pll
- atombios_crtc_set_disp_eng_pll
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 35222b5934)
Cc: stable@vger.kernel.org
[Why]
The boolean fast_validate is used as an
input parameter in multiple functions. To
support more scenarios, we are
replacing it with enum dc_validate_mode.
[How]
The enum dc_validate_mode introduces three
possible values:
1) DC_VALIDATE_MODE_AND_PROGRAMMING:
Apply the mode to hardware
2) DC_VALIDATE_MODE_ONLY:
Check whether the mode can be supported
3) DC_VALIDATE_MODE_AND_STATE_INDEX:
Check if the mode can be supported, and
determine the optimal voltage level
needed to support it.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yan Li <yan.li@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are several gaps that can result in SubVP being enabled with
incompatible HW cursor sizes, and unjust restrictions to cursor size due
to wrong predictions on future usage of SubVP.
[HOW]
- remove "prediction" logic in favor of tagging based on previous SubVP
usage
- block SubVP if current HW cursor settings are incompatible
- provide interface for DM to determine if HW cursor should be disabled
due to an attempt to enable SubVP
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are several gaps that can result in SubVP being enabled with
incompatible HW cursor sizes, and unjust restrictions to cursor size due
to wrong predictions on future usage of SubVP
[HOW]
- remove "prediction" logic in favor of tagging based on previous SubVP
usage
- block SubVP if current HW cursor settings are incompatible
- provide interface for DM to determine if HW cursor should be disabled
due to an attempt to enable SubVP
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Classify DCE6 resource and sequencer as they are for other DCE versions
Put dce60_resource.c and .h under amd/display/dc/resource/dce60
Put and rename dce60_hw_sequencer.c and .h under amd/display/dc/hwss/dce60
v2: fix build when CONFIG_DRM_AMD_DC_SI=n (Alex)
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
