Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms (Dan
Williams)
- Switch vmd from custom domain number allocator to the common
allocator to prevent a potential race with new non-VMD buses (Dan
Williams)
- Enable Precision Time Measurement (PTM) only if device advertises
support for a relevant role, to prevent invalid PTM Requests that
cause ACS violations that are reported as AER Uncorrectable
Non-Fatal errors (Mika Westerberg)
Resource management:
- Prevent resource tree corruption when BAR resize fails (Ilpo
Järvinen)
- Restore BARs to the original size if a BAR resize fails (Ilpo
Järvinen)
- Remove BAR release from BAR resize attempts by the xe, i915, and
amdgpu drivers so the PCI core can restore BARs if the resize fails
(Ilpo Järvinen)
- Move Resizable BAR code to rebar.c (Ilpo Järvinen)
- Add pci_rebar_size_supported() and use it in i915 and xe (Ilpo
Järvinen)
- Add pci_rebar_get_max_size() and use it in xe and amdgpu (Ilpo
Järvinen)
Power management and error handling:
- For drivers using PCI legacy suspend, save config state at suspend
so that state (not any earlier state from enumeration, probe, or
error recovery) will be restored when resuming (Lukas Wunner)
- For devices with no driver or a driver that lacks power management,
save config state at hibernate so that state (not any earlier state
from enumeration, probe, or error recovery) will be restored when
resuming (Lukas Wunner)
- Save device config space on device addition, before driver binding,
so error recovery works more reliably (Lukas Wunner)
- Drop pci_save_state() from several drivers that no longer need it
since the PCI core always does it and pci_restore_state() no longer
invalidates the saved state (Lukas Wunner)
- Document use of pci_save_state() by drivers to capture the state
they want restored during error recovery (Lukas Wunner)
Power control:
- Add a struct pci_ops.assert_perst() function pointer to
assert/deassert PCIe PERST# and implement it for the qcom driver
(Krishna Chaitanya Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe
switch, which must be held in reset after poweron so the pwrctrl
driver can configure the switch via I2C before bringing up the
links (Krishna Chaitanya Chundru)
Endpoint framework:
- Convert the endpoint doorbell test to use a threaded IRQ to fix a
'sleeping while atomic' issue (Bhanu Seshu Kumar Valluri)
- Add endpoint VNTB MSI doorbell support to reduce latency between
host and endpoint (Frank Li)
New native PCIe controller drivers:
- Add CIX Sky1 host controller DT binding and driver (Hans Zhang)
- Add NXP S32G host controller DT binding and driver (Vincent
Guittot)
- Add Renesas RZ/G3S host controller DT binding and driver (Claudiu
Beznea)
- Add SpacemiT K1 host controller DT binding and driver (Alex Elder)
Amlogic Meson PCIe controller driver:
- Update DT binding to name DBI region 'dbi', not 'elbi', and update
driver to support both (Manivannan Sadhasivam)
Apple PCIe controller driver:
- Move struct pci_host_bridge allocation from pci_host_common_init()
to callers, which significantly simplifies pcie-apple (Marc
Zyngier)
Broadcom STB PCIe controller driver:
- Disable advertising ASPM L0s support correctly (Jim Quinlan)
- Add a panic/die handler to print diagnostic info in case PCIe
caused an unrecoverable abort (Jim Quinlan)
Cadence PCIe controller driver:
- Add module support for Cadence platform host and endpoint
controller driver (Manikandan K Pillai)
- Split headers into 'legacy' (LGA) and 'high perf' (HPA) to prepare
for new CIX Sky1 driver (Manikandan K Pillai)
MediaTek PCIe controller driver:
- Convert DT binding to YAML schema (Christian Marangi)
- Add Airoha AN7583 DT compatible and driver support (Christian
Marangi)
Qualcomm PCIe controller driver:
- Add Qualcomm Kaanapali to SM8550 DT binding (Qiang Yu)
- Add required 'power-domains' and 'resets' to qcom sa8775p, sc7280,
sc8280xp, sm8150, sm8250, sm8350, sm8450, sm8550, x1e80100 DT
schemas (Krzysztof Kozlowski)
- Look up OPP using both frequency and data rate (not just frequency)
so RPMh votes can account for both (Krishna Chaitanya Chundru)
Rockchip DesignWare PCIe controller driver:
- Add Rockchip RK3528 compatible strings in DT binding (Yao Zi)
STMicroelectronics STM32MP25 PCIe controller driver:
- Fix a race between link training and endpoint register
initialization (Christian Bruel)
- Align endpoint allocations to match the ATU requirements (Christian
Bruel)
Synopsys DesignWare PCIe controller driver:
- Clear L1 PM Substate Capability 'Supported' bits unless glue driver
says it's supported, which prevents users from enabling non-working
L1SS. Currently only qcom and tegra194 support L1SS (Bjorn Helgaas)
- Remove now-superfluous L1SS disable code from tegra194 (Bjorn
Helgaas)
- Configure L1SS support in dw-rockchip when DT says
'supports-clkreq' (Shawn Lin)
TI Keystone PCIe controller driver:
- Fail the probe instead of silently succeeding if ks_pcie_of_data
didn't specify Root Complex or Endpoint mode (Siddharth Vadapalli)
- Make keystone buildable as a loadable module, except on ARM32 where
hook_fault_code() is __init (Siddharth Vadapalli)"
* tag 'pci-v6.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (100 commits)
MAINTAINERS: Add Manivannan Sadhasivam as PCI/pwrctrl maintainer
MAINTAINERS: Add CIX Sky1 PCIe controller driver maintainer
PCI: sky1: Add PCIe host support for CIX Sky1
dt-bindings: PCI: Add CIX Sky1 PCIe Root Complex bindings
PCI: cadence: Add support for High Perf Architecture (HPA) controller
MAINTAINERS: Add NXP S32G PCIe controller driver maintainer
PCI: s32g: Add NXP S32G PCIe controller driver (RC)
PCI: dwc: Add register and bitfield definitions
dt-bindings: PCI: s32g: Add NXP S32G PCIe controller
PCI: Add Renesas RZ/G3S host controller driver
PCI: host-generic: Move bridge allocation outside of pci_host_common_init()
dt-bindings: PCI: Add Renesas RZ/G3S PCIe controller binding
PCI: Validate pci_rebar_size_supported() input
Documentation: PCI: Amend error recovery doc with pci_save_state() rules
treewide: Drop pci_save_state() after pci_restore_state()
PCI/ERR: Ensure error recoverability at all times
PCI/PM: Stop needlessly clearing state_saved on enumeration and thaw
PCI/PM: Reinstate clearing state_saved in legacy and !PM codepaths
PCI: dw-rockchip: Configure L1SS support
PCI: tegra194: Remove unnecessary L1SS disable code
...
In 2009, commit c82f63e411 ("PCI: check saved state before restore")
changed the behavior of pci_restore_state() such that it became necessary
to call pci_save_state() afterwards, lest recovery from subsequent PCI
errors fails.
The commit has just been reverted and so all the pci_save_state() after
pci_restore_state() calls that have accumulated in the tree are now
superfluous. Drop them.
Two drivers chose a different approach to achieve the same result:
drivers/scsi/ipr.c and drivers/net/ethernet/intel/e1000e/netdev.c set the
pci_dev's "state_saved" flag to true before calling pci_restore_state().
Drop this as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> # qat
Link: https://patch.msgid.link/c2b28cc4defa1b743cf1dedee23c455be98b397a.1760274044.git.lukas@wunner.de
Remove unnecessary casts of constant values to u16.
C's integer promotion rules make them ints no matter what.
Additionally replace E1000_MNG_VLAN_NONE with resulting value
rather than casting -1 to u16.
Signed-off-by: Jacek Kowalski <jacek@jacekk.info>
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In both the read callback for struct cyclecounter, and in struct
timecounter, struct cyclecounter is declared as a const pointer.
Unfortunatly, a number of users of this pointer treat it as a non-const
pointer as it is burried in a larger structure that is heavily modified by
the callback function when accessed. This lie had been hidden by the fact
that container_of() "casts away" a const attribute of a pointer without any
compiler warning happening at all.
Fix this all up by removing the const attribute in the needed places so
that everyone can see that the structure really isn't const, but can,
and is, modified by the users of it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/2025070124-backyard-hurt-783a@gregkh
On some systems with Nahum 11 and Nahum 13 the value of the XTAL clock in
the software STRAP is incorrect. This causes the PTP timer to run at the
wrong rate and can lead to synchronization issues.
The STRAP value is configured by the system firmware, and a firmware
update is not always possible. Since the XTAL clock on these systems
always runs at 38.4MHz, the driver may ignore the STRAP and just set
the correct value.
Fixes: cc23f4f0b6 ("e1000e: Add support for Meteor Lake")
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Reviewed-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add support for netdev-genl, allowing users to query IRQ, NAPI, and queue
information.
After this patch is applied, note the IRQs assigned to my NIC:
$ cat /proc/interrupts | grep ens | cut -f1 --delimiter=':'
50
51
52
While e1000e allocates 3 IRQs (RX, TX, and other), it looks like e1000e
only has a single NAPI, so I've associated the NAPI with the RX IRQ (50
on my system, seen above).
Note the output from the cli:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 2}'
[{'id': 145, 'ifindex': 2, 'irq': 50}]
This device supports only 1 rx and 1 tx queue. so querying that:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump queue-get --json='{"ifindex": 2}'
[{'id': 0, 'ifindex': 2, 'napi-id': 145, 'type': 'rx'},
{'id': 0, 'ifindex': 2, 'napi-id': 145, 'type': 'tx'}]
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Duplicated register initialization codes exist in e1000_configure_tx()
and e1000_configure_rx().
For example, writel(0, tx_ring->head) writes 0 to tx_ring->head, which
is adapter->hw.hw_addr + E1000_TDH(0).
This initialization is already done in ew32(TDH(0), 0).
ew32(TDH(0), 0) is equivalent to __ew32(hw, E1000_TDH(0), 0). It
executes writel(0, hw->hw_addr + E1000_TDH(0)). Since variable hw is
set to &adapter->hw, it is equal to writel(0, tx_ring->head).
We can remove similar four writel() in e1000_configure_tx() and
e1000_configure_rx().
commit 0845d45e90 ("e1000e: Modify Tx/Rx configurations to avoid
null pointer dereferences in e1000_open") has introduced these
writel(). This commit moved register writing to
e1000_configure_tx/rx(), and as result, it caused duplication in
e1000_configure_tx/rx().
This patch modifies the sequence of register writing, but removing
these writes is safe because the same writes were already there before
the commit.
I also have checked the datasheets [0] [1] and have not found any
description that we need to write RDH, RDT, TDH and TDT registers
twice at initialization. Furthermore, we have tested this patch on an
I219-V device physically.
Link: https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/82577-gbe-phy-datasheet.pdf [0]
Link: https://www.intel.com/content/www/us/en/content-details/613460/intel-82583v-gbe-controller-datasheet.html [1]
Tested-by: Kohei Enju <enjuk@amazon.com>
Signed-off-by: Takamitsu Iwai <takamitz@amazon.co.jp>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Sporadic issues, such as PHY access loss, have been observed on I219 (19)
devices. It was found that these devices have hardware more closely
related to ADP than MTP and the issues were caused by taking MTP-specific
flows.
Change the MAC and board types of these devices from MTP to ADP to
correctly reflect the LAN hardware, and flows, of these devices.
Fixes: db2d737d63 ("e1000e: Separate MTP board type from ADP")
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Occasionally when the system goes into pm_suspend, the suspend might fail
due to a PHY access error on the network adapter. Previously, this would
have caused the whole system to fail to go to a low power state.
An example of this was reported in the following Bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=205015
[ 1663.694828] e1000e 0000:00:19.0 eth0: Failed to disable ULP
[ 1664.731040] asix 2-3:1.0 eth1: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 1665.093513] e1000e 0000:00:19.0 eth0: Hardware Error
[ 1665.596760] e1000e 0000:00:19.0: pci_pm_resume+0x0/0x80 returned 0 after 2975399 usecs
and then the system never recovers from it, and all the following suspend failed due to this
[22909.393854] PM: pci_pm_suspend(): e1000e_pm_suspend+0x0/0x760 [e1000e] returns -2
[22909.393858] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -2
[22909.393861] PM: Device 0000:00:1f.6 failed to suspend async: error -2
This can be avoided by changing the return values of __e1000_shutdown and
e1000e_pm_suspend functions so that they always return 0 (success). This
is consistent with what other drivers do.
If the e1000e driver encounters a hardware error during suspend, potential
side effects include slightly higher power draw or non-working wake on
LAN. This is preferred to a system-level suspend failure, and a warning
message is written to the system log, so that the user can be aware that
the LAN controller experienced a problem during suspend.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205015
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On vPro systems, the configuration of the I219-LM to achieve power
gating and S0ix residency is split between the driver and the CSME FW.
It was discovered that in some scenarios, where the network cable is
connected and then disconnected, S0ix residency is not always reached.
This was root-caused to a subset of I219-LM register writes that are not
performed by the CSME FW. Therefore, the driver should perform these
register writes on corporate setups, regardless of the CSME FW state.
This was discovered on Meteor Lake systems; however it is likely to
appear on other platforms as well.
Fixes: cc23f4f0b6 ("e1000e: Add support for Meteor Lake")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218589
Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240628201754.2744221-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit 861e808602 ("e1000e: move force SMBUS from enable ulp
function to avoid PHY loss issue") introduces a regression on
PCH_MTP_I219_LM18 (PCIID: 0x8086550A). Without the referred commit, the
ethernet works well after suspend and resume, but after applying the
commit, the ethernet couldn't work anymore after the resume and the
dmesg shows that the NIC link changes to 10Mbps (1000Mbps originally):
[ 43.305084] e1000e 0000:00:1f.6 enp0s31f6: NIC Link is Up 10 Mbps Full Duplex, Flow Control: Rx/Tx
Without the commit, the force SMBUS code will not be executed if
"return 0" or "goto out" is executed in the enable_ulp(), and in my
case, the "goto out" is executed since FWSM_FW_VALID is set. But after
applying the commit, the force SMBUS code will be ran unconditionally.
Here move the force SMBUS code back to enable_ulp() and put it
immediately ahead of hw->phy.ops.release(hw), this could allow the
longest settling time as possible for interface in this function and
doesn't change the original code logic.
The issue was found on a Lenovo laptop with the ethernet hw as below:
00:1f.6 Ethernet controller [0200]: Intel Corporation Device [8086:550a]
(rev 20).
And this patch is verified (cable plug and unplug, system suspend
and resume) on Lenovo laptops with ethernet hw: [8086:550a],
[8086:550b], [8086:15bb], [8086:15be], [8086:1a1f], [8086:1a1c] and
[8086:0dc7].
Fixes: 861e808602 ("e1000e: move force SMBUS from enable ulp function to avoid PHY loss issue")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-net-2024-05-28-intel-net-fixes-v1-1-dc8593d2bbc6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switch the Intel networking drivers to use the new power management ops
declaration formats and macros, which allows us to drop __maybe_unused,
as well as a bunch of ifdef checking CONFIG_PM.
This is safe to do because the compiler drops the unused functions,
verified by checking for any of the power management function symbols
being present in System.map for a build without CONFIG_PM.
If a driver has runtime PM, define the ops with pm_ptr(), and if the
driver has Simple PM, use pm_sleep_ptr(), as well as the new versions of
the macros for declaring the members of the pm_ops structs.
Checked with network-enabled allnoconfig, allyesconfig, allmodconfig on
x64_64.
Reviewed-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Forcing SMBUS inside the ULP enabling flow leads to sporadic PHY loss on
some systems. It is suspected to be caused by initiating PHY transactions
before the interface settles.
Separating this configuration from the ULP enabling flow and moving it to
the shutdown function allows enough time for the interface to settle and
avoids adding a delay.
Fixes: 6607c99e70 ("e1000e: i219 - fix to enable both ULP and EEE in Sx state")
Co-developed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor several older Intel drivers to use FIELD_GET(), which reduces
lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
(
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add devices IDs for the next LOM generations that will be available on the
next Intel Client platforms. This patch provides the initial support for
these devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
On some I219 devices, ethernet cable plugging detection only works once
from PCI D3 state. Subsequent cable plugging does set PME bit correctly,
but device still doesn't get woken up.
Since I219 connects to the root complex directly, it relies on platform
firmware (ACPI) to wake it up. In this case, the GPE from _PRW only
works for first cable plugging but fails to notify the driver for
subsequent plugging events.
The issue was originally found on CNP, but the same issue can be found
on ADL too. So workaround the issue by continuing use PME poll after
first ACPI wake. As PME poll is always used, the runtime suspend
restriction for CNP can also be removed.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this doesn't control interrupt generation by the Root Port; that
is controlled by the AER Root Error Command register, which is managed by
the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
e1000_xmit_frame is expected to stop the queue and dispatch frames to
hardware if there is not sufficient space for the next frame in the
buffer, but sometimes it failed to do so because the estimated maximum
size of frame was wrong. As the consequence, the later invocation of
e1000_xmit_frame failed with NETDEV_TX_BUSY, and the frame in the buffer
remained forever, resulting in a watchdog failure.
This change fixes the estimated size by making it match with the
condition for NETDEV_TX_BUSY. Apparently, the old estimation failed to
account for the following lines which determines the space requirement
for not causing NETDEV_TX_BUSY:
```
/* reserve a descriptor for the offload context */
if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
count++;
count++;
count += DIV_ROUND_UP(len, adapter->tx_fifo_limit);
```
This issue was found when running http-stress02 test included in Linux
Test Project 20220930 on QEMU with the following commandline:
```
qemu-system-x86_64 -M q35,accel=kvm -m 8G -smp 8
-drive if=virtio,format=raw,file=root.img,file.locking=on
-device e1000e,netdev=netdev
-netdev tap,script=ifup,downscript=no,id=netdev
```
Fixes: bc7f75fa97 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add tracepoints to the driver via a new file e1000e_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for s0ix flows to help in a debug of shared resources with the CSME
firmware. The idea here is that tracepoints have such low performance cost
when disabled that we can leave these in the upstream driver.
Performance not affected, and this can be very useful for debugging and
adding new trace events to paths in the future.
Usage:
echo "e1000e_trace:*" > /sys/kernel/debug/tracing/set_event
echo 1 > /sys/kernel/debug/tracing/events/e1000e_trace/enable
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add devices IDs for the next LOM generations that will be available on the
next Intel Client platforms.
This patch provides the initial support for these devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We have the same LAN controller on different PCH's. Separate MTP board
type from an ADP which will allow for specific fixes to be applied for MTP
platforms.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The PTP implementation for the e1000e driver uses the older .adjfreq
method. This method takes an adjustment in parts per billion. The newer
.adjfine implementation uses scaled_ppm. The use of scaled_ppm allows for
finer grained adjustments and is preferred over using the older
implementation.
Make use of mul_u64_u64_div_u64 in order to handle possible overflow of the
multiplication used to calculate the desired adjustment to the hardware
increment value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)"
to compute headers length for a TCP packet, but others
use more convoluted (but equivalent) ways.
Add skb_tcp_all_headers() and skb_inner_tcp_all_headers()
helpers to harmonize this a bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handshake with CSME/AMT on none provisioned platforms during S0ix flow
is not supported on TGL platform and can cause to HW unit hang. Update
the handshake with CSME flow to start from the ADL platform.
Fixes: 3e55d23171 ("e1000e: Add handshake with the CSME to support S0ix")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
