The DWMAC1000 supports 2 timestamping configurations to configure how
frequency adjustments are made to the ptp_clock, as well as the reported
timestamp values.
There was a previous attempt at upstreaming support for configuring this
mode by Olivier Dautricourt and Julien Beraud a few years back [1]
In a nutshell, the timestamping can be either set in fine mode or in
coarse mode.
In fine mode, which is the default, we use the overflow of an accumulator to
trigger frequency adjustments, but by doing so we lose precision on the
timetamps that are produced by the timestamping unit. The main drawback
is that the sub-second increment value, used to generate timestamps, can't be
set to lower than (2 / ptp_clock_freq).
The "fine" qualification comes from the frequent frequency adjustments we are
able to do, which is perfect for a PTP follower usecase.
In Coarse mode, we don't do frequency adjustments based on an
accumulator overflow. We can therefore have very fine subsecond
increment values, allowing for better timestamping precision. However
this mode works best when the ptp clock frequency is adjusted based on
an external signal, such as a PPS input produced by a GPS clock. This
mode is therefore perfect for a Grand-master usecase.
Introduce a driver-specific devlink parameter "ts_coarse" to enable or
disable coarse mode, keeping the "fine" mode as a default.
This can then be changed with:
devlink dev param set <dev> name ts_coarse value true cmode runtime
The associated documentation is also added.
[1] : https://lore.kernel.org/netdev/20200514102808.31163-1-olivier.dautricourt@orolia.com/
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20251024070720.71174-3-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Allwinner A523 SoC family has a second Ethernet controller, called
the GMAC200 in the BSP and T527 datasheet, and referred to as GMAC1 for
numbering. This controller, according to BSP sources, is fully
compatible with a slightly newer version of the Synopsys DWMAC core.
The glue layer around the controller is the same as found around older
DWMAC cores on Allwinner SoCs. The only slight difference is that since
this is the second controller on the SoC, the register for the clock
delay controls is at a different offset. Last, the integration includes
a dedicated clock gate for the memory bus and the whole thing is put in
a separately controllable power domain.
Add a new driver for this hardware supporting the integration layer.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250925191600.3306595-3-wens@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Extend the Renesas GBETH stmmac glue driver to support the RZ/T2H SoC,
where the GMAC is connected through a MIIC PCS. Introduce a new
`has_pcs` flag in `struct renesas_gbeth_of_data` to indicate when PCS
handling is required.
When enabled, the driver parses the `pcs-handle` phandle, creates a PCS
instance with `miic_create()`, and wires it into phylink. Proper cleanup
is done with `miic_destroy()`. New init/exit/select hooks are added to
`plat_stmmacenet_data` for PCS integration.
Update Kconfig to select `PCS_RZN1_MIIC` when building the Renesas GBETH
driver so the PCS support is always available.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://patch.msgid.link/20250908105901.3198975-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
igc: Add support for Frame Preemption
Faizal Rahim says:
Introduce support for the FPE feature in the IGC driver.
The patches aligns with the upstream FPE API:
https://patchwork.kernel.org/project/netdevbpf/cover/20230220122343.1156614-1-vladimir.oltean@nxp.com/https://patchwork.kernel.org/project/netdevbpf/cover/20230119122705.73054-1-vladimir.oltean@nxp.com/
It builds upon earlier work:
https://patchwork.kernel.org/project/netdevbpf/cover/20220520011538.1098888-1-vinicius.gomes@intel.com/
The patch series adds the following functionalities to the IGC driver:
a) Configure FPE using `ethtool --set-mm`.
b) Display FPE settings via `ethtool --show-mm`.
c) View FPE statistics using `ethtool --include-statistics --show-mm'.
e) Block setting preemptible tc in taprio since it is not supported yet.
Existing code already blocks it in mqprio.
Tested:
Enabled CONFIG_PROVE_LOCKING, CONFIG_DEBUG_ATOMIC_SLEEP, CONFIG_DMA_API_DEBUG, and CONFIG_KASAN
1) selftests
2) netdev down/up cycles
3) suspend/resume cycles
4) fpe verification
No bugs or unusual dmesg logs were observed.
Ran 1), 2) and 3) with and without the patch series, compared dmesg and selftest logs - no differences found.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: add support to get frame preemption statistics via ethtool
igc: add support to get MAC Merge data via ethtool
igc: block setting preemptible traffic class in taprio
igc: add support to set tx-min-frag-size
igc: add support for frame preemption verification
igc: set the RX packet buffer size for TSN mode
igc: use FIELD_PREP and GENMASK for existing RX packet buffer size
igc: optimize TX packet buffer utilization for TSN mode
igc: use FIELD_PREP and GENMASK for existing TX packet buffer size
igc: rename I225_RXPBSIZE_DEFAULT and I225_TXPBSIZE_DEFAULT
igc: rename xdp_get_tx_ring() for non-xdp usage
net: ethtool: mm: reset verification status when link is down
net: ethtool: mm: extract stmmac verification logic into common library
net: stmmac: move frag_size handling out of spin_lock
====================
Link: https://patch.msgid.link/20250418163822.3519810-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It appears that stmmac is not the only hardware which requires a
software-driven verification state machine for the MAC Merge layer.
While on the one hand it's good to encourage hardware implementations,
on the other hand it's quite difficult to tolerate multiple drivers
implementing independently fairly non-trivial logic.
Extract the hardware-independent logic from stmmac into library code and
put it in ethtool. Name the state structure "mmsv" for MAC Merge
Software Verification. Let this expose an operations structure for
executing the hardware stuff: sync hardware with the tx_active boolean
(result of verification process), enable/disable the pMAC, send mPackets,
notify library of external events (reception of mPackets), as well as
link state changes.
Note that it is assumed that the external events are received in hardirq
context. If they are not, it is probably a good idea to disable hardirqs
when calling ethtool_mmsv_event_handle(), because the library does not
do so.
Also, the MM software verification process has no business with the
tx_min_frag_size, that is all the driver's to handle.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Co-developed-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Tested-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Tested-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Intel platform will configure the SerDes through PMC API based on the
provided interface mode.
This patch adds several new functions below:-
- intel_tsn_lane_is_available(): This new function reads FIA lane
ownership registers and common lane registers through IPC commands
to know which lane the mGbE port is assigned to.
- intel_mac_finish(): To configure the SerDes based on the assigned
lane and latest interface mode, it sends IPC command to the PMC through
PMC driver/API. The PMC acts as a proxy for R/W on behalf of the driver.
- intel_set_reg_access(): Set the register access to the available TSN
interface.
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Link: https://patch.msgid.link/20250227121522.1802832-6-yong.liang.choong@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a missing quirk to enable support for the StarFive JH7100 SoC.
Additionally, for greater flexibility in operation, allow using the
rgmii-rxid and rgmii-txid phy modes.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only present the DWMAC_LOONGSON option on architectures where it can
actually be used.
This follows the same logic as the DWMAC_INTEL option.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This glue driver is created based on the arch-code
implemented earlier with the platform-specific settings.
Use syscon for SYSCON register access.
And modify MAINTAINERS to add a new F: entry for this driver.
Partially based on the previous work by Serge Semin.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dwmac_socfpga re-implements support for the TSE PCS, which is identical
to the already existing TSE PCS, which in turn is the same as the Lynx
PCS. Drop the existing TSE re-implemenation and use the Lynx PCS
instead, relying on the regmap-mdio driver to translate MDIO accesses
into mmio accesses.
Add a lynx_pcs reference in the stmmac's internal structure, and use
.mac_select_pcs() to return the relevant PCS to be used.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCOM_SOCINFO depends on QCOM_SMEM but is not selected, this cause some
problems with QCOM_SOCINFO getting selected with the dependency of
QCOM_SMEM not met.
To fix this remove the select in Kconfig and add additional info in the
DWMAC_IPQ806X config description.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 9ec092d2fe ("net: ethernet: stmmac: add missing sgmii configure for ipq806x")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for Ingenic SoC MAC glue layer support for the stmmac
device driver. This driver is used on for the MAC ethernet controller
found in the JZ4775 SoC, the X1000 SoC, the X1600 SoC, the X1830 SoC,
and the X2000 SoC.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify 32-bit and 64-bit Intel SoCFPGA Kconfig options by having only
one for both of them. This the common practice for other platforms.
Additionally, the ARCH_SOCFPGA is too generic as SoCFPGA designs come
from multiple vendors.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add dwmac-visconti to the stmmac driver in Toshiba Visconti ARM SoCs.
This patch contains only the basic function of the device. There is no
clock control, PM, etc. yet. These will be added in the future.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create drivers/net/pcs and move the Synopsys DesignWare XPCS into the
new directory. Move the header file into a subdirectory
include/linux/pcs
Start a naming convention of all PCS files use the prefix pcs-, and
rename the XPCS files to fit.
v2:
Add include/linux/pcs
v4:
Fix include path in stmmac.
Remove PCS_DEVICES to avoid new prompts
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dwmac-intel-plat to enable the stmmac driver in Intel Keem Bay.
Also add fix_mac_speed and tx_clk in order to change link speeds.
This is required as mac_speed_o is not connected in the
Intel Keem Bay SoC.
Signed-off-by: Rusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
NXP imx8 family like imx8mp/imx8dxl chips support Synopsys MAC 5.10a IP.
This patch adds settings for NXP imx8 glue layer:
- clocks
- dwmac address width
- phy interface mode selection
- adjust rgmii txclk rate
v2:
- adjust code sequences in order to have reverse christmas
tree local variable ordering.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As stmmac_pci.c file is getting bigger and more complex, it is reasonable
to separate all the Intel specific dwmac pci device to a different file.
This move includes Intel Quark, TGL and EHL. A new kernel config
CONFIG_DWMAC_INTEL is introduced and depends on X86. For this initial
patch, all the necessary function such as probe() and exit() are identical
besides the function name.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mapping and unmapping DMA region is an high bottleneck in stmmac driver,
specially in the RX path.
This commit introduces support for Page Pool API and uses it in all RX
queues. With this change, we get more stable troughput and some increase
of banwidth with iperf:
- MAC1000 - 950 Mbps
- XGMAC: 9.22 Gbps
Changes from v3:
- Use page_pool_destroy() (Ilias)
Changes from v2:
- Uncoditionally call page_pool_free() (Jesper)
Changes from v1:
- Use page_pool_get_dma_addr() (Jesper)
- Add a comment (Jesper)
- Add page_pool_free() call (Jesper)
- Reintroduce sync_single_for_device (Arnd / Ilias)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix gcc build error while CONFIG_INET is not set
drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.o: In function `__stmmac_test_loopback':
stmmac_selftests.c:(.text+0x8ec): undefined reference to `ip_send_check'
stmmac_selftests.c:(.text+0xacc): undefined reference to `udp4_hwcsum'
Add CONFIG_INET dependency to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add support for selftests on stmmac driver with 9 basic sanity checks
for now:
- MAC Loopback
- PHY Loopback
- MMC Counters
- EEE
- Hash Filter Multicast
- Perfect Filter Unicast
- Multicast Filter All
- Unicast Filter All
- Flow Control
This allows for fast tracking of regressions in the driver and helps in
spotting mis-configuration of HW.
Changes from v1:
- Fix build error as module (David)
- Check for link status before running tests
Changes from RFC v2:
- Return proper error code in stmmac_test_mmc (Corentin)
- Use only 1 MMC counter in stmmac_test_mmc (Alexandre)
Changes from RFC v1:
- Change test_loopback to test_mac_loopback (Andrew)
- Change timeout to retries (Andrew)
- Add MC/UC filter tests (Andrew)
- Only test in offline mode (Andrew)
- Do not call phy_loopback twice (Alexandre)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add glue driver to support Qualcomm ETHQOS using stmmac driver.
This is based on downstream driver written by Siddarth Gupta, Sunil
Kumar Paidimarri, Rahul Ankushrao Kawadgave, Nisha Menon, Jagadeesh
Babu Challagundla, Chaitanya Pratapa, Lakshit Tyagi, Suraj Jaiswal,
Sneh Shah and Ventrapragada Ravi Kanth
Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Stratix10 SoC is an AARCH64 based platform that shares the same ethernet
controller that is on other SoCFPGA platforms. Build the platform driver.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bde4975310.
All legacy clock implementations now implement clk_set_rate() (Some
implementations may be dummies, though).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arnd.de>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Stratix10 platform has an additional reset line, OCP(Open Core Protocol),
that also needs to get deasserted for the stmmac ethernet controller to work.
Thus we need to update the Kconfig to include ARCH_STRATIX10 in order to build
dwmac-socfpga.
Also, remove the redundant check for the reset controller pointer. The
reset driver already checks for the pointer and returns 0 if the pointer
is NULL.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the build failure on m68k;
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: In function `ipq806x_gmac_probe':
dwmac-ipq806x.c:(.text+0xda): undefined reference to `clk_set_rate'
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.o: In function `rk_gmac_probe':
dwmac-rk.c:(.text+0x1e58): undefined reference to `clk_set_rate'
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.o: In function `stid127_fix_retime_src':
dwmac-sti.c:(.text+0xd8): undefined reference to `clk_set_rate'
dwmac-sti.c:(.text+0x114): undefined reference to `clk_set_rate'
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.o:dwmac-sti.c:(.text+0x12c): more undefined references to `clk_set_rate' follow
Lots of stmmac platform drivers need COMMON_CLK in their Kconfig depends.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
