Pull SoC fixes from Arnd Bergmann:
"The main code change is a revert of the Raspberry Pi RP1 overlay
support that was decided to not be ready.
The other fixes are all for devicetree sources:
- ethernet configuration on ixp42x-actiontec-mi424wr is board
revision specific
- validation warning fixes for imx27/imx51/imx6, hikey960 and k3
- Minor corrections across imx8 boards, addressing all types of
issues with interrups, dma, ethernet and clock settings, all simple
one-line changes"
* tag 'soc-fixes-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
arm64: dts: hisilicon: hikey960: Drop "snps,gctl-reset-quirk" and "snps,tx_de_emphasis*" properties
Documentation/process: maintainer-soc: Mark 'make' as commands
Documentation/process: maintainer-soc: Be more explicit about defconfig
arm64: dts: mba8mx: Fix Ethernet PHY IRQ support
arm64: dts: imx8qm-ss-dma: correct the dma channels of lpuart
arm64: dts: imx8mp: Fix LAN8740Ai PHY reference clock on DH electronics i.MX8M Plus DHCOM
arm64: dts: freescale: tx8p-ml81: fix eqos nvmem-cells
arm64: dts: freescale: moduline-display: fix compatible
dt-bindings: arm: fsl: moduline-display: fix compatible
ARM: dts: imx6q-ba16: fix RTC interrupt level
arm64: dts: freescale: imx95-toradex-smarc: fix SMARC_SDIO_WP label position
arm64: dts: freescale: imx95-toradex-smarc: use edge trigger for ethphy1 interrupt
arm64: dts: add off-on-delay-us for usdhc2 regulator
arm64: dts: imx8qm-mek: correct the light sensor interrupt type to low level
ARM: dts: nxp: imx: Fix mc13xxx LED node names
arm64: dts: imx95: correct I3C2 pclk to IMX95_CLK_BUSWAKEUP
MAINTAINERS: Fix a linusw mail address
arm64: dts: broadcom: rp1: drop RP1 overlay
arm64: dts: broadcom: bcm2712: fix RP1 endpoint PCI topology
misc: rp1: drop overlay support
...
Pull Char/Misc/IIO/Binder updates from Greg KH:
"Here is the big set of char/misc/iio and other driver subsystem
changes for 6.18-rc1.
Loads of different stuff in here, it was a busy development cycle in
lots of different subsystems, with over 27k new lines added to the
tree.
Included in here are:
- IIO updates including new drivers, reworking of existing apis, and
other goodness in the sensor subsystems
- MEI driver updates and additions
- NVMEM driver updates
- slimbus removal for an unused driver and some other minor updates
- coresight driver updates and additions
- MHI driver updates
- comedi driver updates and fixes
- extcon driver updates
- interconnect driver additions
- eeprom driver updates and fixes
- minor UIO driver updates
- tiny W1 driver updates
But the majority of new code is in the rust bindings and additions,
which includes:
- misc driver rust binding updates for read/write support, we can now
write "normal" misc drivers in rust fully, and the sample driver
shows how this can be done.
- Initial framework for USB driver rust bindings, which are disabled
for now in the build, due to limited support, but coming in through
this tree due to dependencies on other rust binding changes that
were in here. I'll be enabling these back on in the build in the
usb.git tree after -rc1 is out so that developers can continue to
work on these in linux-next over the next development cycle.
- Android Binder driver implemented in Rust.
This is the big one, and was driving a huge majority of the rust
binding work over the past years. Right now there are two binder
drivers in the kernel, selected only at build time as to which one
to use as binder wants to be included in the system at boot time.
The binder C maintainers all agreed on this, as eventually, they
want the C code to be removed from the tree, but it will take a few
releases to get there while both are maintained to ensure that the
rust implementation is fully stable and compliant with the existing
userspace apis.
All of these have been in linux-next for a while"
* tag 'char-misc-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (320 commits)
rust: usb: keep usb::Device private for now
rust: usb: don't retain device context for the interface parent
USB: disable rust bindings from the build for now
samples: rust: add a USB driver sample
rust: usb: add basic USB abstractions
coresight: Add label sysfs node support
dt-bindings: arm: Add label in the coresight components
coresight: tnoc: add new AMBA ID to support Trace Noc V2
coresight: Fix incorrect handling for return value of devm_kzalloc
coresight: tpda: fix the logic to setup the element size
coresight: trbe: Return NULL pointer for allocation failures
coresight: Refactor runtime PM
coresight: Make clock sequence consistent
coresight: Refactor driver data allocation
coresight: Consolidate clock enabling
coresight: Avoid enable programming clock duplicately
coresight: Appropriately disable trace bus clocks
coresight: Appropriately disable programming clocks
coresight: etm4x: Support atclk
coresight: catu: Support atclk
...
Pull SoC devicetree updates from Arnd Bergmann:
"There are a few new variants of existing chips:
- mt6572 is an older mobile phone chip from mediatek that was
extremely popular a decade ago but never got upstreamed until now
- exynos2200 is a recent high-end mobile phone chip used in a few
Samsung phones like the Galaxy S22
- Renesas R-Car V4M-7 (R8A779H2) is an updated version of R-Car V4M
(R8A779H0) and used in automotive applications
- Tegra264 is a new chip from NVIDIA, but support is fairly minimal
for now, and not much information is public about it
There are five more chips in a separate branch, as those are new chip
families that I merged along with the necessary infrastructure.
New board support is not that exciting, with a total of 33 newly added
machines here:
- Evaluation platforms for the chips above, plus TI am62d2 and Sophgo
sg2042
- Six 32-bit industrial boards based on stm32, imx6 and am33 chips,
plus eight 64-bit rockchips rk33xx/rk35xx, am62d2, t527, imx8 and
imx95
- Two newly added ASPEED BMC based motherboards, and one that got
removed
- Phones and Tablets based on 32-bit mt6572, tegra30 and 64-bit
msm8976 SoCs
- Three Laptops based on Mediatek mt8186 and Qualcomm Snapdragon X1
- A set-top box based on Amlogic meson-gxm
Updates for existing machines are spread over all the above families.
One notable change here is support for the RP1 I/O chip used in
Raspberry Pi 5"
* tag 'soc-dt-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (606 commits)
riscv: dts: sophgo: fix mdio node name for CV180X
riscv: dts: sophgo: sophgo-srd3-10: reserve uart0 device
riscv: dts: sophgo: add Sophgo SG2042_EVB_V2.0 board device tree
riscv: dts: sophgo: add Sophgo SG2042_EVB_V1.X board device tree
dt-bindings: riscv: add Sophgo SG2042_EVB_V1.X/V2.0 bindings
riscv: dts: sophgo: add ethernet GMAC device for sg2042
riscv: dts: sophgo: Enable ethernet device for Huashan Pi
riscv: dts: sophgo: Add mdio multiplexer device for cv18xx
riscv: dts: sophgo: Add ethernet device for cv18xx
riscv: dts: sophgo: sg2044: add pmu configuration
riscv: dts: sophgo: sg2044: add ziccrse extension
riscv: dts: sophgo: add zfh for sg2042
riscv: dts: sophgo: add ziccrse for sg2042
riscv: dts: sophgo: Add xtheadvector to the sg2042 devicetree
riscv: dts: sophgo: sg2044: add PCIe device support for SG2044
riscv: dts: sophgo: sg2044: add MSI device support for SG2044
riscv: dts: sophgo: add reset configuration for Sophgo CV1800 series SoC
riscv: dts: sophgo: add reset generator for Sophgo CV1800 series SoC
dt-bindings: soc: sophgo: Move SoCs/boards from riscv into soc, add SG2000
riscv: dts: sophgo: sg2044: Add missing riscv,cbop-block-size property
...
dt-bindings: Updates for v6.17-rc1
Add Tegra264 compatible strings for some core components and extend
bindings where necessary to accomodate the new hardware generation. Also
document some new platforms, for both old and new chips.
* tag 'tegra-for-6.17-dt-bindings' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: arm: tegra: Add Asus Portable AiO P1801-T
dt-bindings: arm: tegra: Add Asus VivoTab RT TF600T
dt-bindings: Add Tegra264 clock and reset definitions
dt-bindings: tegra: Document P3971-0089+P3834-0008 Platform
dt-bindings: rtc: tegra: Document Tegra264 RTC
dt-bindings: dma: Add Tegra264 compatible string
dt-bindings: misc: Document Tegra264 APBMISC compatible
dt-bindings: firmware: Document Tegra264 BPMP
dt-bindings: mailbox: tegra-hsp: Properly sort compatible string list
dt-bindings: mailbox: tegra-hsp: Bump number of shared interrupts
dt-bindings: tegra: pmc: Add Tegra264 compatible
dt-bindings: memory: tegra: Add Tegra264 support
Link: https://lore.kernel.org/r/20250711220943.2389322-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The FPC202 dual port controller serves as a low speed signal aggregator for
common port types, notably SFP. It provides access to I2C and low-speed
GPIO signals of a downstream device through a single upstream control
interface.
Up to two logical I2C addresses can be accessed on each of the FPC202's
ports. The port controller acts as an I2C translator (ATR). It converts
addresses of incoming and outgoing I2C transactions. One use case of this
is accessing two SFP modules at logical address 0x50 from the same upstream
I2C controller, using two different client aliases.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add a lwn,bk4-spi.yaml binding for Liebherr's BK4 external SPI controller.
Currently, the compatible string used for this device is "lwn,bk4",
which is the same as the board compatible string documented at fsl.yaml.
This causes several dt-schema warnings:
make dtbs_check DT_SCHEMA_FILES=fsl.yaml
...
['lwn,bk4'] is too short
'lwn,bk4' is not one of ['tq,imx8dxp-tqma8xdp-mba8xx']
'lwn,bk4' is not one of ['tq,imx8qxp-tqma8xqp-mba8xx']
'lwn,bk4' is not one of ['armadeus,imx1-apf9328', 'fsl,imx1ads']
...
Use a more specific "lwn,bk4-spi" compatible string for this
device.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://patch.msgid.link/20241023120015.1049008-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull char / misc driver updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystem changes
for 6.12-rc1.
Lots of changes in here, primarily dominated by the usual IIO driver
updates and additions, but there are also small driver subsystem
updates all over the place. Included in here are:
- lots and lots of new IIO drivers and updates to existing ones
- interconnect subsystem updates and new drivers
- nvmem subsystem updates and new drivers
- mhi driver updates
- power supply subsystem updates
- kobj_type const work for many different small subsystems
- comedi driver fix
- coresight subsystem and driver updates
- fpga subsystem improvements
- slimbus fixups
- binder new feature addition for "frozen" notifications
- lots and lots of other small driver updates and cleanups
All of these have been in linux-next for a long time with no reported
problems"
* tag 'char-misc-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (354 commits)
greybus: gb-beagleplay: Add firmware upload API
arm64: dts: ti: k3-am625-beagleplay: Add bootloader-backdoor-gpios to cc1352p7
dt-bindings: net: ti,cc1352p7: Add bootloader-backdoor-gpios
MAINTAINERS: Update path for U-Boot environment variables YAML
nvmem: layouts: add U-Boot env layout
comedi: ni_routing: tools: Check when the file could not be opened
ocxl: Remove the unused declarations in headr file
hpet: Fix the wrong format specifier
uio: Constify struct kobj_type
cxl: Constify struct kobj_type
binder: modify the comment for binder_proc_unlock
iio: adc: axp20x_adc: add support for AXP717 ADC
dt-bindings: iio: adc: Add AXP717 compatible
iio: adc: axp20x_adc: Add adc_en1 and adc_en2 to axp_data
w1: ds2482: Drop explicit initialization of struct i2c_device_id::driver_data to 0
tools: iio: rm .*.cmd when make clean
iio: adc: standardize on formatting for id match tables
iio: proximity: aw96103: Add support for aw96103/aw96105 proximity sensor
bus: mhi: host: pci_generic: Enable EDL trigger for Foxconn modems
bus: mhi: host: pci_generic: Update EDL firmware path for Foxconn modems
...
Pull char / misc and other driver updates from Greg KH:
"Here is the "big" set of char/misc and other driver subsystem changes
for 6.11-rc1. Nothing major in here, just loads of new drivers and
updates. Included in here are:
- IIO api updates and new drivers added
- wait_interruptable_timeout() api cleanups for some drivers
- MODULE_DESCRIPTION() additions for loads of drivers
- parport out-of-bounds fix
- interconnect driver updates and additions
- mhi driver updates and additions
- w1 driver fixes
- binder speedups and fixes
- eeprom driver updates
- coresight driver updates
- counter driver update
- new misc driver additions
- other minor api updates
All of these, EXCEPT for the final Kconfig build fix for 32bit
systems, have been in linux-next for a while with no reported issues.
The Kconfig fixup went in 29 hours ago, so might have missed the
latest linux-next, but was acked by everyone involved"
* tag 'char-misc-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (330 commits)
misc: Kconfig: exclude mrvl-cn10k-dpi compilation for 32-bit systems
misc: delete Makefile.rej
binder: fix hang of unregistered readers
misc: Kconfig: add a new dependency for MARVELL_CN10K_DPI
virtio: add missing MODULE_DESCRIPTION() macro
agp: uninorth: add missing MODULE_DESCRIPTION() macro
spmi: add missing MODULE_DESCRIPTION() macros
dev/parport: fix the array out-of-bounds risk
samples: configfs: add missing MODULE_DESCRIPTION() macro
misc: mrvl-cn10k-dpi: add Octeon CN10K DPI administrative driver
misc: keba: Fix missing AUXILIARY_BUS dependency
slimbus: Fix struct and documentation alignment in stream.c
MAINTAINERS: CC dri-devel list on Qualcomm FastRPC patches
misc: fastrpc: use coherent pool for untranslated Compute Banks
misc: fastrpc: support complete DMA pool access to the DSP
misc: fastrpc: add missing MODULE_DESCRIPTION() macro
misc: fastrpc: Add missing dev_err newlines
misc: fastrpc: Use memdup_user()
nvmem: core: Implement force_ro sysfs attribute
nvmem: Use sysfs_emit() for type attribute
...
Convert fsl,qoriq-mc from txt to yaml format.
Addition changes:
- Child node name allow 'ethernet'.
- Use 32bit address in example.
- Fixed missed ';' in example.
- Allow dma-coherent.
- Remove smmu, its part in example.
- Change child node name as 'ethernet'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240617170934.813321-1-Frank.Li@nxp.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Convert AMD (Xilinx) sd-fec bindings to yaml format, so it can validate
dt-entries as well as any future additions to yaml.
Change in clocks is due to IP is itself configurable and
only the first two clocks are in all combinations. The last
6 clocks can be present in some of them. It means order is
not really fixed and any combination is possible.
Interrupt may or may not be present.
The documentation for sd-fec bindings is now YAML, so update the
MAINTAINERS file.
Update the link to the new yaml file in xilinx_sdfec.rst.
Signed-off-by: Dragan Cvetic <dragan.cvetic@amd.com>
Link: https://lore.kernel.org/r/20240131170650.530079-1-dragan.cvetic@amd.com
Signed-off-by: Rob Herring <robh@kernel.org>
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 6.5, please pull the following:
- Krzysztof adds missing cache properties for the BCM63xx DSL routers
- Rafal relicenses a number of the BCM5301X DTS files to the GPL 2.0+ / MIT license,
and he fixes a number of Device Tree nodes warnings, adds MAC address
for all Luxul routers and adds Netgear R8000 Wi-Fi regulatory
information to the DTS
- Stanislav updates the "BCM mobile" SoCs DTS files to fix various
warnings
- Aurelien enables the BCM283x DTS files to be built with relocation
information to make them usable with DT overlays
- Christian fixes the Meraki DTS to have correct NAND ECC properties,
correct partition numbers and fixed-link node(s) properties
* tag 'arm-soc/for-6.5/devicetree' of https://github.com/Broadcom/stblinux: (33 commits)
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
ARM: dts: BCM5301X: Add Netgear R8000 WiFi regulator mappings
dt-bindings: net: wireless: brcm,bcm4329-fmac: allow generic properties
dt-bindings: net: wireless: brcm,bcm4329-fmac: add BCM4366 binding
ARM: dts: BCM5301X: fix duplex-full => full-duplex
ARM: dts: BCM5301X: MR32: remove partition index numbers
ARM: dts: BCM5301X: MR26: MR32: remove bogus nand-ecc-algo property
dt-bindings: power: reset: bcm21664-resetmgr: convert to YAML
ARM: dts: bcm21664-garnet: use node labels
ARM: dts: bcm11351/21664: add UART, I2C node labels
ARM: dts: bcm-mobile: move status properties to the end of nodes
ARM: dts: bcm21664/23550: use CCU compatibles directly
ARM: dts: bcm-mobile: change "" includes to <> where applicable
ARM: dts: BCM5301X: Describe switch ports in the main DTS
ARM: dts: BCM5301X: Relicense Christian's code to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Drop invalid properties from Meraki MR32 keys
ARM: dts: BCM5301X: Drop invalid #usb-cells
dt-bindings: arm: bcm: Add bindings for Buffalo WZR-1166DHP(2)
ARM: dts: BCM5301X: Use updated "spi-gpio" binding properties
...
Link: https://lore.kernel.org/r/20230619134920.3384844-1-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Triple Modular Redundancy(TMR) subsystem contains three microblaze cores,
subsystem is fault-tolerant and continues to operate nominally after
encountering an error. Together with the capability to detect and recover
from errors, the implementation ensures the reliability of the entire
subsystem. TMR Manager is responsible for performing recovery of the
subsystem detects the fault via a break signal it invokes microblaze
software break handler which calls the tmr manager driver api to
update the error count and status.
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.kedareswara.rao@amd.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221125054113.122833-2-appana.durga.kedareswara.rao@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc and other driver subsystem changes
for 6.2-rc1. Nothing earth-shattering in here at all, just a lot of
new driver development and minor fixes.
Highlights include:
- fastrpc driver updates
- iio new drivers and updates
- habanalabs driver updates for new hardware and features
- slimbus driver updates
- speakup module parameters added to aid in boot time configuration
- i2c probe_new conversions for lots of different drivers
- other small driver fixes and additions
One semi-interesting change in here is the increase of the number of
misc dynamic minors available to 1048448 to handle new huge-cpu
systems.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (521 commits)
extcon: usbc-tusb320: Convert to i2c's .probe_new()
extcon: rt8973: Convert to i2c's .probe_new()
extcon: fsa9480: Convert to i2c's .probe_new()
extcon: max77843: Replace irqchip mask_invert with unmask_base
chardev: fix error handling in cdev_device_add()
mcb: mcb-parse: fix error handing in chameleon_parse_gdd()
drivers: mcb: fix resource leak in mcb_probe()
coresight: etm4x: fix repeated words in comments
coresight: cti: Fix null pointer error on CTI init before ETM
coresight: trbe: remove cpuhp instance node before remove cpuhp state
counter: stm32-lptimer-cnt: fix the check on arr and cmp registers update
misc: fastrpc: Add dma_mask to fastrpc_channel_ctx
misc: fastrpc: Add mmap request assigning for static PD pool
misc: fastrpc: Safekeep mmaps on interrupted invoke
misc: fastrpc: Add support for audiopd
misc: fastrpc: Rework fastrpc_req_munmap
misc: fastrpc: Use fastrpc_map_put in fastrpc_map_create on fail
misc: fastrpc: Add fastrpc_remote_heap_alloc
misc: fastrpc: Add reserved mem support
misc: fastrpc: Rename audio protection domain to root
...
Convert Qualcomm FastRPC bindings to yaml format, so that we could validate
dt-entries correctly and any future additions can go into yaml format.
Use compute-cb@ subnodes instead of just cb@. Add qcom,glink-channels and
qcom,smd-channels missing properties to make sure dtbs_check doesn't fail
right off the bat. Correct the name of the parent node in the example from
smd-edge to glink-edge.
Since now the qcom,fastrpc bindings document is yaml, update the
reference to it in qcom,glink-edge and also use $ref.
Also update the MAINTAINERS file to point to the yaml version.
Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Co-developed-by: David Heidelberg <david@ixit.cz>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220907074301.3996021-1-abel.vesa@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pull devicetree updates from Rob Herring:
"Bindings:
- Add spi-peripheral-props.yaml references to various SPI device
bindings
- Convert qcom,pm8916-wdt, ds1307, Qualcomm BAM DMA, is31fl319x,
skyworks,aat1290, Rockchip EMAC, gpio-ir-receiver, ahci-ceva, Arm
CCN PMU, rda,8810pl-intc, sil,sii9022, ps2-gpio, and
arm-firmware-suite bindings to DT schema format
- New bindings for Arm virtual platforms display, Qualcomm IMEM
memory region, Samsung S5PV210 ChipID, EM Microelectronic EM3027
RTC, and arm,cortex-a78ae
- Add vendor prefixes for asrock, bytedance, hxt, ingrasys, inventec,
quanta, and densitron
- Add missing MSI and IOMMU properties to host-generic-pci
- Remove bindings for removed EFM32 platform
- Remove old chosen.txt binding (replaced by schema)
- Treewide add missing type information for properties
- Treewide fixing of typos and its vs. it's in bindings. Its all good
now.
- Drop unnecessary quoting in power related schemas
- Several LED binding updates which didn't get picked up
- Move various bindings to proper directories
DT core code:
- Convert unittest GPIO related tests to use fwnode
- Check ima-kexec-buffer against memory bounds
- Print reserved-memory allocation/reservation failures as errors
- Cleanup early_init_dt_reserve_memory_arch()
- Simplify of_overlay_fdt_apply() tail"
* tag 'devicetree-for-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (65 commits)
dt-bindings: mtd: microchip,mchp48l640: use spi-peripheral-props.yaml
dt-bindings: power: supply: drop quotes when not needed
dt-bindings: power: reset: drop quotes when not needed
dt-bindings: power: drop quotes when not needed
dt-bindings: PCI: host-generic-pci: Allow IOMMU and MSI properties
of/fdt: declared return type does not match actual return type
devicetree/bindings: correct possessive "its" typos
dt-bindings: net: convert emac_rockchip.txt to YAML
dt-bindings: eeprom: microchip,93lc46b: move to eeprom directory
dt-bindings: eeprom: at25: use spi-peripheral-props.yaml
dt-bindings: display: use spi-peripheral-props.yaml
dt-bindings: watchdog: qcom,pm8916-wdt: convert to dtschema
dt-bindings: power: reset: qcom,pon: use absolute path to other schema
dt-bindings: iio/dac: adi,ad5766: Add missing type to 'output-range-microvolts'
dt-bindings: power: supply: charger-manager: Add missing type for 'cm-battery-stat'
dt-bindings: panel: raydium,rm67191: Add missing type to 'video-mode'
of/fdt: Clean up early_init_dt_reserve_memory_arch()
dt-bindings: PCI: fsl,imx6q-pcie: Add missing type for 'reset-gpio-active-high'
dt-bindings: rtc: Add EM Microelectronic EM3027 bindings
dt-bindings: rtc: ds1307: Convert to json-schema
...
Instead of listing directly properties typical for SPI peripherals,
reference the spi-peripheral-props.yaml schema. This allows using all
properties typical for SPI-connected devices, even these which device
bindings author did not tried yet.
Remove the spi-* properties which now come via spi-peripheral-props.yaml
schema, except for the cases when device schema adds some constraints
like maximum frequency.
While changing additionalProperties->unevaluatedProperties, put it in
typical place, just before example DTS.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220727164424.386499-1-krzysztof.kozlowski@linaro.org
The VCPU stall detection mechanism allows to configure the expiration
duration and the internal counter clock frequency measured in Hz.
Add these properties in the schema.
While this is a memory mapped virtual device, it is expected to be loaded
when the DT contains the compatible: "qemu,vcpu-stall-detector" node.
In a protected VM we trust the generated DT nodes and we don't rely on
the host to present the hardware peripherals.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Link: https://lore.kernel.org/r/20220711081720.2870509-2-sebastianene@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
