This patch adds support to decode system memory bandwidth and other
parameters for skylake and Gen9+ platforms, which will be used for
arbitrated display memory bandwidth calculation in GEN9 based
platforms and WM latency level-0 Work-around calculation on GEN9+.
Changes Since V1:
- s/memdev_info/dram_info
- create a struct to hold channel info
Changes Since V2:
- rewrite code to adhere i915 coding style
- not valid for GLK
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824093225.12598-3-mahesh1.kumar@intel.com
There are two issues with the current RPCS programming for Icelake:
Expansion of the slice count bitfield has been missed, as well as the
required programming workaround for the subslice count bitfield size
limitation.
1)
Bitfield width for configuring the active slice count has grown so we need
to program the GEN8_R_PWR_CLK_STATE accordingly.
Current code was always requesting eight times the number of slices (due
writing to a bitfield starting three bits higher than it should). These
requests were luckily a) capped by the hardware to the available number of
slices, and b) we haven't yet exported the code to ask for reduced slice
configurations.
Due both of the above there was no impact from this incorrect programming
but we should still fix it.
2)
Due subslice count bitfield being only three bits wide and furthermore
capped to a maximum documented value of four, special programming
workaround is needed to enable more than four subslices.
With this programming driver has to consider the GT configuration as
2x4x8, while the hardware internally translates this to 1x8x8.
A limitation stemming from this is that either a subslice count between
one and four can be selected, or a subslice count equaling the total
number of subslices in all selected slices. In other words, odd subslice
counts greater than four are impossible, as are odd subslice counts
greater than a single slice subslice count.
This also had no impact in the current code base due breakage from 1)
always reqesting more than one slice.
While fixing this we also add some asserts to flag up any future bitfield
overflows.
v2:
* Use a local in all branches for clarity. (Lionel)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bspec: 12247
Reported-by: tony.ye@intel.com
Suggested-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: tony.ye@intel.com
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180903113007.2643-1-tvrtko.ursulin@linux.intel.com
Unlike the other ports, TC ports are not available to use as soon as
we get a hotplug. The TC PHYs can be shared between multiple
controllers: display, USB, etc. As a result, handshaking through FIA
is required around connect and disconnect to cleanly transfer
ownership with the controller and set the type-C power state.
This patch implements the flow sequences described by our
specification. We opt to grab ownership of the ports as soon as we get
the hotplugs in order to simplify the interactions and avoid surprises
in the user space side. We may consider changing this in the future,
once we improve our testing capabilities on this area.
v2:
* This unifies the DP and HDMI patches so we can discuss everything
at once so people looking at random single patches can actually
understand the direction.
* I found out the spec was updated a while ago. There's a small
difference in the connect flow and the patch was updated for that.
* Our spec also now gives a good explanation on what is really
happening. As a result, comments were added.
* Add some more comments as requested by Rodrigo (Rodrigo).
v3:
* Downgrade a DRM_ERROR that shouldn't ever happen but we can't act
on in case it does (Chris).
BSpec: 21750, 4250.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801173441.9789-1-paulo.r.zanoni@intel.com
PLLs are the source clocks for the DDIs so in order to determine the
ddi clock we need to check the PLL configuration.
For MG PHy Ports (C - F), depending on whether it is a TBT PLL or MG
PLL the link lock can be obtained from the the PLL divisors based on
the specification.
v2 (from Paulo):
* Make the algorithm look more like what's in the spec, also document
where we differ form the spec and why.
* Make the code a little more consistent with our coding style.
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817215209.29133-2-paulo.r.zanoni@intel.com
The register value of Divider Ratio for high speed divider
(hsdiv_ratio) in MG_CLKTOP2_HSCLKCTL_PORT register is not same as the
actual numerical value of the divider. So this patch implements
separate divider value defines for that field.
icl_mg_pll_find_divisors() can use these defines instead of magic
register values.
The new defines are going to be used in the next patch.
v2 (from Paulo):
* Rebase.
* Make it look a little more like the rest of our code.
v3 (from Paulo):
* Make hsdiv u32 now that it's a bit field (José).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Suggested-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817215209.29133-1-paulo.r.zanoni@intel.com
Instead of defining all registers twice, define just a PCH_GPIO_BASE
that has the same address as PCH_GPIO_A and use that to calculate all
the others. This also brings VLV and !HAS_GMCH_DISPLAY in line, doing
the same thing.
v2: Fix GMBUS registers to be relative to gpio base; create GPIO()
macro to return a particular gpio address and move the enum out of
i915_reg.h (suggested by Jani)
v3: Move base offset inside the GPIO() macro so the GMBUS defines don't
actually need to be changed (suggested by Daniel/Ville)
v4: Move definition of i915_gpio to intel_display.h and remove
GMBUS/GPIO handling from gvt since now they have their own
defines.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727193647.8639-3-lucas.demarchi@intel.com
Since Haswell we have no color range indication either in the pipe or
port registers for DP. Instead, there's a separate register for setting
the DP Main Stream Attributes (MSA) directly. The MSA register
definition makes no references to colorimetry, just a vague reference to
the DP spec. The connection to the color range was lost.
Apparently we've failed to set the proper MSA bit for limited, or CEA,
range ever since the first DDI platforms. We've started setting other
MSA parameters since commit dae847991a ("drm/i915: add
intel_ddi_set_pipe_settings").
Without the crucial bit of information, the DP sink has no way of
knowing the source is actually transmitting limited range RGB, leading
to "washed out" colors. With the colorimetry information, compliant
sinks should be able to handle the limited range properly. Native
(i.e. non-LSPCON) HDMI was not affected because we do pass the color
range via AVI infoframes.
Though not the root cause, the problem was made worse for DDI platforms
with commit 55bc60db59 ("drm/i915: Add "Automatic" mode for the
"Broadcast RGB" property"), which selects limited range RGB
automatically based on the mode, as per the DP, HDMI and CEA specs.
After all these years, the fix boils down to flipping one bit.
[Per testing reports, this fixes DP sinks, but not the LSPCON. My
educated guess is that the LSPCON fails to turn the CEA range MSA into
AVI infoframes for HDMI.]
Reported-by: Michał Kopeć <mkopec12@gmail.com>
Reported-by: N. W. <nw9165-3201@yahoo.com>
Reported-by: Nicholas Stommel <nicholas.stommel@gmail.com>
Reported-by: Tom Yan <tom.ty89@gmail.com>
Tested-by: Nicholas Stommel <nicholas.stommel@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=100023
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107476
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94921
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.9+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180814060001.18224-1-jani.nikula@intel.com
There is no need for separate IDs for power wells on a new platform with
the same functionality as an other power well on a previous platform, we
can just reuse the ID from the previous platform. This is only possible
after the previous patches where we removed dependence on the actual
enum values.
This also fixes a problem on ICL where in assert_can_enable_dc5/9() we
would've failed to look up the PW#2 power well.
v2:
- Keep an ID assigned for the ICL PW#2 power well too. (Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Added comment about the ICL PW#2 fix to the commit log]
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-10-imre.deak@intel.com
Now that we removed dependence on the power well IDs to determine the
control register and request/status flag offsets the only purpose of
power well IDs is to look up power wells directly bypassing the power
domains framework. However this direct lookup isn't needed for most of
the exisiting power wells and hopefully won't be needed for any new
power wells in the future. To make maintenance of the power well ID enum
easier, don't require a unique ID for each power well, only if it's
necessary. Remove the IDs becoming redundant this way and assign to all
the corresponding power wells a new DISP_PW_ID_NONE ID.
After the previous two patches the IDs don't need to have a fixed value,
so remove the explicit initializers and adjust the enum's code comment
accordingly.
v2:
- Keep required ID assignments for HSW_DISP_PW_GLOBAL and ICL_DISP_PW_2.
(Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-8-imre.deak@intel.com
Similarly to the previous patch use a separate request/status HW flag
index defined right after the corresponding control registers instead of
depending for this on the power well IDs. Since the set of
control/status registers varies among the different power wells (on a
single platform), also add a new i915_power_well_registers struct that
we populate and assign to each DDI power well as needed.
Also clarify a bit the code comment describing the function and layout
of the control registers.
This also fixes a problem on ICL, where we incorrectly read the KVMR
control register in hsw_power_well_requesters() even for DDI and AUX
power wells.
v2:
- Clarify platform range tags in code comments. (Paulo)
- Fix line over 80 chars checkpatch warning.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-7-imre.deak@intel.com
Atm, we determine the control/status flag offsets within the PUNIT
control/status registers based on the power well's ID. Since the power
well ID enum is global across all platforms, the associated macros to
get the flag offsets involves some magic. This makes checking the
register/bit definitions against the specification more difficult than
necessary. Also the values in the power well ID enum must stay fixed,
making code maintenance of the enum cumbersome.
To solve the above define the control/status flag indices right after
the corresponding registers and use these to derive the control/status
flag values by storing the indices in the i915_power_well_desc struct.
Initializing anonymous union fields require the preceding field in the
struct to be explicitly initialized - even when using named
initializers - and the initialization to be done right before the union
initialization, hence the reordering of the .id fields.
v2:
- Clarify commit log message about anonymous union initializers. (Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-6-imre.deak@intel.com
This patch adds the remaining register definitions and bit fields
required for MG PHy DDI buffer initializations and voltage
swing programming for MG PHy DDI ports.
While at it this patch also fixes the naming for previously defined
MG PHY registers in original commit id (c92f47b5ec "drm/i915/icl:
Add register defs for voltage swing sequences for MG PHY DDI").
Since the MG PHY registers are first defined in ICL platform, there
is no need for _ICL prefix.
v4 (from Paulo): add two white spaces to CRI_CALCINIT too.
v3:
* Fix register names, add spaces for MASK defines, correct the order
of #defines (Paulo)
v2:
* Change the MG_TX_DRVCTL registers names to match the spec (Anusha)
Cc: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531510993-6606-1-git-send-email-manasi.d.navare@intel.com
Support for Burst read in HW is added for HDCP2.2 compliance
requirement.
This patch enables the burst read for all the gmbus read of more than
511Bytes, on capable platforms.
v2:
Extra line is removed.
v3:
Macro is added for detecting the BURST_READ Support [Jani]
Runtime detection of the need for burst_read [Jani]
Calculation enhancement.
v4:
GMBUS0 reg val is passed from caller [ville]
Removed a extra var [ville]
Extra brackets are removed [ville]
Implemented the handling of 512Bytes Burst Read.
v5:
Burst read max length is fixed at 767Bytes [Ville]
v6:
Collecting the received reviewed-by.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1530192889-5789-3-git-send-email-ramalingam.c@intel.com
Adjust the EIR clearing to cope with the edge triggered IIR
on i965/g4x. To guarantee an edge in the ISR master error bit
we temporarily mask everything in EMR. As some of the EIR bits
can't even be directly cleared we also borrow a trick from
i915_clear_error_registers() and permanently mask any bit that
remains high. No real thought given to how we might unmask them
again once the cause for the error has been clered. I suppose
on pre-g4x GPU reset will reinitialize EMR from scratch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
This patch addresses Interrupts from south display engine (SDE).
ICP has two registers - SHOTPLUG_CTL_DDI and SHOTPLUG_CTL_TC.
Introduce these registers and their intended values.
Introduce icp_irq_handler().
The icp_irq_postinstall() takes care of
enabling all PCH interrupt sources, to unmask
them as needed with SDEIMR, as is done
done by ibx_irq_pre_postinstall() for earlier platforms.
We do not need to explicitly call the ibx_irq_pre_postinstall().
Also, while changing these,
s/CPT/PPT/CPT-CNP comment.
v2:
- remove redundant register defines.(Lucas)
- Change register names to be more consistent with
previous platforms (Lucas)
v3:
-Reorder bit defines to a more appropriate location.
Change the comments. Confirm in the commit message that
icp_irq_postinstall() need not go to
ibx_irq_pre_postinstall() and ibx_irq_postinstall()
as in earlier platforms. (Paulo)
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
[Paulo: coding style bikesheds and rebases].
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530046343-30649-1-git-send-email-anusha.srivatsa@intel.com
Add the definition for ICL power wells and their mapping to power
domains. On ICL there are 3 power well control registers, we'll select
the correct one based on higher bits of the power well ID. The offset
for the control and status flags within this register is based on the
lower bits of the ID as on older platforms.
As the DC state programming is also the same as on old platforms we can
reuse the corresponding helpers. For this we mark here the DC-off power
well as shared among multiple platforms.
Other than the above the delta between old platforms and ICL:
- Pipe C has its own power well, so we can save some additional power in the
pipe A+B and (non-eDP) pipe A configurations.
- Power wells for port E/F DDI/AUX IO and Thunderbolt 1-4 AUX IO
v2:
- Rebase on drm-tip after prep patch for this was merged there as
requested by Paulo.
- Actually add the new AUX and DDI power well control regs (Rakshmi)
v3:
- Fix power well register names in code comments
- Add TBT AUX->power well 3 dependency
v4:
- Rebase
v5:
- Detach AUX power wells from the INIT power domain. These power wells
can only be enabled in a TC/TBT connected state and otherwise not
needed during driver initialization.
v6:
- Use _MMIO_PORT(...) instead _MMIO(_PICK(...)) (Paulo)
Fix checkpatch warnings.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com> (v1)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626142232.22361-1-imre.deak@intel.com
Sink can be configured to calculate the CRC over the static frame and
compare with the CRC calculated and transmited in the VSC SDP by
source, if there is a mismatch sink will do a short pulse in HPD
and set DP_PSR_LINK_CRC_ERROR in DP_PSR_ERROR_STATUS.
Spec: 7723
v6:
andling DP_PSR_LINK_CRC_ERROR here and remove "bdw+" from commit
message
v4:
patch moved to after 'drm/i915/psr: Avoid PSR exit max time timeout'
to avoid touch in 2 patches EDP_PSR_DEBUG.
v3:
disabling PSR instead of exiting on error
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-5-jose.souza@intel.com
