For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf514 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull MTD updates from Brian Norris:
- refactor m25p80.c driver for use as a general SPI NOR framework for
other drivers which may speak to SPI NOR flash without providing full
SPI support (i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
* tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd: (77 commits)
mtd: gpmi: add gpmi support for imx6sx
mtd: maps: remove check for CONFIG_MTD_SUPERH_RESERVE
mtd: bf5xx_nand: use the managed version of kzalloc
mtd: pxa3xx_nand: make the driver work on big-endian systems
mtd: nand: omap: fix omap_calculate_ecc_bch() for-loop error
mtd: nand: r852: correct write_buf loop bounds
mtd: nand_bbt: handle error case for nand_create_badblock_pattern()
mtd: nand_bbt: remove unused variable
mtd: maps: sc520cdp: fix warnings
mtd: slram: fix unused variable warning
mtd: pfow: remove unused variable
mtd: lpddr: fix Kconfig dependency, for I/O accessors
mtd: nand: pxa3xx: Add supported ECC strength and step size to the DT binding
mtd: nand: pxa3xx: Use ECC strength and step size devicetree binding
mtd: nand: pxa3xx: Clean pxa_ecc_init() error handling
mtd: nand: Warn the user if the selected ECC strength is too weak
mtd: nand: omap: Documentation: How to select correct ECC scheme for your device ?
mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
mtd: nand: omap: add support for BCH16_ECC - ELM driver updates
mtd: nand: omap: add support for BCH16_ECC - GPMC driver updates
...
OMAP NAND driver support multiple ECC scheme, which can used in different
flavours, depending on in-build Hardware engines present on SoC.
This patch updates following in DT bindings related to sectionion of ecc-schemes
- ti,elm-id: replaces elm_id (maintains backward compatibility)
- ti,nand-ecc-opts: selection of h/w or s/w implementation of an ecc-scheme
depends on ti,elm-id. (supported values ham1, bch4, and bch8)
- maintain backward compatibility to deprecated DT bindings (sw, hw, hw-romcode)
Below table shows different flavours of ecc-schemes supported by OMAP devices
+---------------------------------------+---------------+---------------+
| ECC scheme |ECC calculation|Error detection|
+---------------------------------------+---------------+---------------+
|OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W |
|(requires CONFIG_MTD_NAND_ECC_BCH) | | |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
|(requires CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id in DT) | | |
+---------------------------------------+---------------+---------------+
To optimize footprint of omap2-nand driver, selection of some ECC schemes
also require enabling following Kconfigs, in addition to setting appropriate
DT bindings
- Kconfig:CONFIG_MTD_NAND_ECC_BCH error detection done in software
- Kconfig:CONFIG_MTD_NAND_OMAP_BCH error detection done by h/w engine
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
OMAP devices support various NAND transfer modes.
Currently all device-tree definitions will use the default "prefetch
polled" mode, so this patch enables the transfer mode to be specified
in the device-tree.
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPMC timing properties for device-tree have been updated
by adding a "-ns" or "-ps" suffix to indicate the units of
time the property represents. Therefore, update the timing
property names for TI GPMC NAND example.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
In case ELM module available, omap2 NAND driver can opt for hardware
correction method for bit flip errors in NAND flash with BCH. Hence the
detection of ELM module is done through devicetree population of elm_id.
This patch update device tree documentation for gpmc-nand for elm-id
data population.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds basic DT bindings for OMAP GPMC.
The actual peripherals are instantiated from child nodes within the GPMC
node, and the only type of device that is currently supported is NAND.
Code was added to parse the generic GPMC timing parameters and some
documentation with examples on how to use them.
Successfully tested on an AM33xx board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
