Merge "ARM: tegra: device tree changes for 3.15" from Stephen Warren:
This enables:
- host1x and eDP support on Tegra124.
- LCD panel support for a few Tegra20 devices and Venice2.
- Enables power down, SPI flash, and USB on Venice2.
- Documents which Dalmore revision is supported.
- Adds an I2C bus mux to Cardhu.
Additionally, Tegra124 is converted to use #address-cells=<2> since the
HW suports more than 32-bits of address space, and various cleanups are
included.
* tag 'tegra-for-3.15-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (21 commits)
ARM: dts: tegra: add PCIe interrupt mapping properties
ARM: tegra: use 2 address cells for Tegra124 DT
ARM: tegra: Rename as3722 node to pmic
ARM: tegra: Fix whitespace around '='
ARM: tegra: Enable USB on Venice2
ARM: tegra: Add Tegra124 USB support
ARM: tegra: Enable eDP for Venice2
ARM: tegra: Add Tegra124 eDP support
ARM: tegra: Add Tegra124 host1x support
ARM: tegra: Hook up SDMMC3 power-supply on Venice2
ARM: tegra: Overhaul Venice2 regulators
ARM: tegra: Combine VBUS enable pins into one node
ARM: tegra: Use "disabled" for status property
ARM: tegra: add SPI flash to Venice2 DT
ARM: tegra: enable PCA9546 on Cardhu
ARM: tegra: enable LCD panel on Ventana
ARM: tegra: enable LCD panel on Seaboard
ARM: tegra: add system-power-controller property for PMIC node
ARM: tegra: document which Dalmore revisions are supported
ARM: tegra: Properly sort clocks property
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This describes a compatible entry of the form:
ethernet-phy-idAAAA,BBBB
Which is modelled after the PCI structured compatible entry
(pciVVVV,DDDD.SSSS.ssss.RR)
If present the OF core will be able to use this information to
directly create the correct phy without auto probing the bus.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Cirrus Logic CS42448/CS42888 Audio CODEC that
has six/four 24-bit AD and eight 24-bit DA converters.
[ CS42448/CS42888 supports both I2C and SPI control ports. As initial patch,
this patch only adds the support for I2C. ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Missing bindings were found on running checkpatch.pl on bsc9132
device tree. This patch add/update the following
- Add bindings for L2 cache controller
- Add bindings for memory controller
- Update bindings for USB controller
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch series adds basic uprobes support to ARM. It is based on
patches developed earlier by Rabin Vincent. That approach of adding
hooks into the kprobes instruction parsing code was not well received.
This approach separates the ARM instruction parsing code in kprobes out
into a separate set of functions which can be used by both kprobes and
uprobes. Both kprobes and uprobes then provide their own semantic action
tables to process the results of the parsing.
Allwinner sunXi SoCs clock changes
This adds support for the new, more correct clock node naming and gets
the A10 compatibles in line with the rest of the other SoCs. It also
adds support for the USB, GMAC and A31's PLL6 clocks. Some of these
changes also require DT modifications that will be merged via arm-soc.
Add device tree bindings for OMAP Display Subsystem for the following
SoCs: OMAP2, OMAP3, OMAP4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
PM8921 and PM8058 are PMICs found paired with MSM8960 and MSM8660
devices respectively. They contain subdevices such as keypads,
RTC, regulators, clocks, etc.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MOXA ART SoCs allow to determine PLL output and APB frequencies
by reading registers holding multiplier and divisor information.
Add a clock driver for this SoC.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The current simple-card driver separates the daimft for cpu_dai and codec_dai.
So we might get different values for them (0x4003 and 0x1003 for example):
asoc-simple-card sound-cs42888.12: cpu : 2024000.esai / 4003 / 132000000
asoc-simple-card sound-cs42888.12: codec : cs42888 / 1003 / 24576000
asoc-simple-card sound-cs42888.12: cs42888 <-> 2024000.esai mapping ok
This is not allowed at all as we need to keep the DAIFMT settings identical
for both the ends of the link.
Thus this patch fixes it by overwriting the cpu_dai->fmt with codec_dai->fmt
since we defined the DAIFMT_MASTER basing on CODEC at the first place while
the other bits are same.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a new driver for the ARM CLPS711X Pulse Width Modulator (PWM) interface.
This CPU contain two 4-bit PWM outputs with constant period, based on CPU
PLL frequency. PWM polarity is determined by hardware by power on reset.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The Armada 370 DB board not only has analog audio input/output, but
also S/PDIF input/output. This commit adds support for S/PDIF in the
ASoC machine driver of the Armada 370 DB platform, and adjusts the
Device Tree bindings documentation accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge "STi DT changes part 1 v2" from Srinivas Kandagatla:
Patches : 01-02 are DT patches, adding interrupt support to pin
controller driver, Driver changes are already going via Linus W's
pinctrl tree.
Patches: 03 - 06 are DT patches for reset/softreset controller. Reset
controller driver is Acked by Philipp Zabel.
Patches: 07, 08 are DT patches, adding Ethernet controller support
patches, actual driver changes are already in v3.14-rc4 via Dave Millers
net tree.
Patches: 09, 10 are DT patches for IR driver support, actual IR driver
is already available since v3.12. Reason for the delay is due to
dependency on reset controller driver/headers.
* tag 'DT-for-v3.15-part-1-v2' of git://git.stlinux.com/devel/kernel/linux-sti:
ARM: STi: STIH416: Add IR support.
ARM: STi: STIH415: Add IR support.
ARM: STi: STiH416: Add ethernet support.
ARM: STi: STiH415: Add ethernet support.
ARM: STi: STiH416: Add soft reset controller support.
ARM: STi: STiH416: Add reset controller support.
ARM: STi: STiH415: Add soft reset controller support.
ARM: STi: STiH415: Add reset controller support.
ARM: STi: STiH415: Add interrupt support for pin controller
ARM: STi: STiH416: Add interrupt support for pin controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SYSCON driver was designed for using memory areas (registers)
that are used in several subsystems. There are systems (CPUs)
which use bits in one register for various purposes and thus
should be handled by various kernel subsystems. This driver
allows you to use the individual SYSCON bits as GPIOs.
ARM CLPS711X SYSFLG1 input lines has been added as first user
of this driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add devicetree binding documentation for twl4030-madc
analog digital converter.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a bindings description for the Altera Triple Speed Ethernet
(TSE) driver. The bindings support the legacy SGDMA soft IP as well as the
preferred MSGDMA soft IP. The TSE can be configured and synthesized in soft
logic using Altera's Quartus toolchain. Please consult the bindings document
for supported options.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reviewing an i2c driver for efm32 that needs a similar property
Wolfram Sang pointed out that "location" is a too generic name for something
that is efm32 specific. So add an appropriate namespace and fall back to the
generic name in case of failure.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds dt entry for ahci sata controller and its
corresponding phy controller.phy node has been added w.r.t
new generic phy framework.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This resolves a merge issue with drivers/staging/cxt1e1/linux.c that was
fixed in a report from Stephen Rothwell
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.15: First pull request
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge "ARM: mach-bcm: dt updates for 3.15 - part 2" from Matt Porter:
- BCM21664 SoC support
- BCM59056 PMU support
- BCM281xx reboot fix
* tag 'armsoc/for-3.15/dt-2' of git://github.com/broadcom/mach-bcm:
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Updates to the .dts files to support more Gumstix boards.
These are sent separately from the rest of the .dts changes
as these depend on the fixes merged into v3.14-rc4, and
needed a bit more time to get updated on the fixes.
* tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add support for the Overo Summit
ARM: dts: Add support for the Overo Chestnut43
ARM: dts: Add support for the Overo Alto35
ARM: dts: Add support for the Overo Gallop43
ARM: dts: Add support for the Overo Palo43
ARM: dts: overo: Add LIS33DE accelerometer
ARM: dts: overo: Create a file for common Gumstix peripherals
ARM: dts: overo: Push uart3 pinmux down to expansion board
ARM: dts: omap3-tobi: Add AT24C01 EEPROM
ARM: dts: omap3-tobi: Use include file omap-gpmc-smsc9221
ARM: dts: omap: Add common file for SMSC9221
ARM: dts: omap3-overo: Add HSUSB PHY
ARM: dts: omap3-overo: Enable WiFi/BT combo
ARM: dts: omap3-overo: Add missing pinctrl
ARM: dts: omap3-tobi: Add missing pinctrl
ARM: dts: overo: reorganize include files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/boot/dts/omap3-overo.dtsi
The dts Makefile has a bunch of nasty conflicts, attempt to resolve
these now to avoid trouble later.
Conflicts:
arch/arm/boot/dts/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
