This binding specifies a set of common properties for display panels. It
can be used as a basis by bindings for specific panels.
Bindings for three specific panels are provided to show how the simple
panel binding can be used.
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Document the device tree bindings for the MIPI DSI bus. The MIPI Display
Serial Interface specifies a serial bus and a protocol for communication
between a host and up to four peripherals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a new DMA_TYPE for SSI dual FIFO script, included
in SDMA firmware version 2. This script would allow SSI use dual
fifo mode to transimit/receive data without occasional hardware
underrun/overrun.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Added a binding example for reference and updated the
node name. While at it also removed the name description
as it is not necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the mmc device tree node entries for exynos5420 SOC.
Exynos5420 has a different version of DWMMC controller,so a new
compatible string is used to distinguish it from the prior SOC's.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a driver for SILabs 570, 571, 598, 599 programmable oscillators.
The devices generate low-jitter clock signals and are reprogrammable via
an I2C interface.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Device tree clock binding document for EMMA Mobile EV2 SMU,
And Common clock framework based implementation of it.
Following nodes are defined to describe clock tree.
- renesas,emev2-smu
- renesas,emev2-smu-clkdiv
- renesas,emev2-smu-gclk
These bindings are designed manually based on
19UH0037EJ1000_SMU : System Management Unit User's Manual
So far, reparent is not implemented, and is fixed to index #0.
Clock tree description is not included, and should be provided
by device-tree.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Register the firmware operations for Trusted Foundations if the device
tree indicates it is active on the device.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the Device Tree bindings documentation for the Trusted Foundation
secure monitor.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds very basic device tree files for the Marvell Armada 1500 SoC
(Berlin BG2) and the Sony NSZ-GS7 GoogleTV board. Currently, SoC only has
nodes for cpus, some clocks, l2 cache controller, local timer, apb timers,
uart, and interrupt controllers. The Sony NSZ-GS7 is a GoogleTV consumer
device comprising the Armada 1500 SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
This adds an irqchip driver and corresponding devicetree binding for the
secondary interrupt controllers based on Synopsys DesignWare IP dw_apb_ictl.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
MSTP clocks are gate clocks controlled through a register that handles
up to 32 clocks. The register is often sparsely populated.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DIV6 clocks are divider gate clocks controlled through a single
register. The divider is expressed on 6 bits, hence the name, and can
take values from 1/1 to 1/64.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:
- Fixed rate clocks with multiplier and divisor set according to boot
mode configuration
- Custom divider clocks with SoC-specific divider values
This driver supports both.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Added device tree support for TI's Keystone USB driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Added device tree support for TI's Keystone USB PHY driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This device tree binding document describes the Tegra124 pincontrol
DT bindings. This document lists all valid properties, names, mux
options of Tegra124 pins.
Changes from V1:
- Referred the dt-binding header file on describing the nodes.
Changes from V2:
- Rewording reg properties.
- drop drv_type as it is not applicable.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On non-DT platforms IRQ controllers associated with the GPIOs have a
fixed IRQ base value known at compile time. The sh-pfc driver translates
GPIO number to IRQ numbers using a hardcoded table. This mechanism
breaks on DT platforms, as the IRQ base values are dynamic in that case.
Fix this by specifying IRQs associated with GPIOs in IRQ resources,
populated automatically from the device tree. When IRQ resources are
specified the driver requires one IRQ resource per GPIO able to generate
an interrupt, and uses the translation table to compute the IRQ resource
offset instead of the IRQ number.
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra124 adds a number of extra modules into the configlink bus, which
must be taken out of reset before the bus is used. Update the AHUB
driver to know about these extra modules (the AHUB HW module hosts the
configlink bus).
Based-on-work-by: Arun Shamanna Lakshmi <aruns@nvidia.com>
Based-on-work-by: Songhee Baek <sbaek@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@linaro.org>
---
This patch depends on "ASoC: tegra: use reset framework" to compile,
which is ack'd and slated to go through a (large) topic branch in the
Tegra tree. So, we can either:
a) Merge that Tegra topic branch into the ASoC tree, then apply this.
Note that I haven't created the topic branch yet, since I'm still
waiting for DMA dependencies to be applied.
b) Apply this change to the Tegra tree too. This change isn't directly
related to the changes in the Tegra tree; it just makes use of the new
reset controller feature that's introduced there.
Add support for Device Tree and use of the DMA DT API to
get the channels if needed.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the channels if needed.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the needed channels.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Update all the Tegra DT bindings to require the standard dmas/dma-names
properties rather than non-standard nvidia,dma-request-selector property.
This is a DT-ABI-incompatible change. It is the second of two changes
required for me to consider the Tegra DT bindings as stable, the other
being the previous conversion to the common reset bindings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Update all the Tegra DT bindings to require resets/reset-names properties
where the HW module has reset inputs. Remove any entries from clocks or
clock-names that were only required to identify reset inputs, rather than
referring to real clocks.
This is a DT-ABI-incompatible change. It is the first of two changes
required for me to consider the Tegra DT bindings as stable, the other
being conversion to the common DMA DT bindings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Commit 89ce376c6b (drivers/net: Use of_match_ptr() macro in smc91x.c)
added minimal device tree support to smc91x, but it's not working on
many platforms because of the lack of some key configuration bits.
Fix the issue by parsing the necessary configuration like the
smc911x driver is doing. As most smc91x users seem to use 16-bit
access, let's default to that if no reg-io-width is specified.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Linus Walleij:
Two integrator device tree patches for v3.14:
- Delete some static core module mappings.
- Move EBI location to the device tree.
* tag 'integrator-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: move EBI to the device tree
ARM: integrator: delete static core module mappings
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Most of the Allwinner SoCs (at this time, all but the A10) also have a
High Speed timers that are not using the 24MHz oscillator as a source
but rather the AHB clock running much faster.
The IP is slightly different between the A10s/A13 and the one used in
the A20/A31, since the latter have 4 timers available, while the former
have only 2 of them.
[dlezcano] : Fixed conflict with b788beda "Order Kconfig options
alphabetically"
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
From Nicolas Ferre:
First DT pull-request for 3.14
- many little corrections and documentation updates
- LCD FB Device Tree for at91sam9263 and at91sam9g45 boards
- crypto peripherals DT entries + DMA specification
- new Cosino board
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/at91rm9200ek.dts: rearrange nodes in address ascending order
ARM: at91: dt: at91rm9200ek: add emac and nor flash support
ARM: at91: add uart aliases to sama5d3 dtsi
ARM: at91: add i2c2 pinctrl speficifation to sama5d3 DT
ARM: at91: Animeo IP: fix mtd partition table
ARM: at91: at91sam9g45: add i2c pinctrl
ARM: at91: at91sam9g45: set default mmc pinctrl-names
ARM: at91: sama5d3: enable qt1070 as a wakeup source
ARM: at91: add support for Cosino board series by HCE Engineering
ARM: at91/dt/sama5d3: add DMA information to SHA/AES/TDES nodes
ARM: at91/dt/trivial: before sama5d3, Atmel MPU were using at91 prefix
ARM: at91/dt/trivial: use macro for AES irq type
ARM: at91: sam9263ek: add dt lcd support
ARM: at91: at9sam9m10g45ek: add dt lcd support
ARM: at91: sam9263: add fb dt support
ARM: at91: sam9g45: add fb dt support
ARM: at91/dt: binding: add missing compatibility string in SDRAM/DDR documentation
ARM: at91/dt: binding: add precision to AIC documentation
ARM: at91/dt: add atmel,pullup-gpio to at91rm9200ek usb1 definition
ARM: at91/dt: add ethernet phy to at91rm9200ek board
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
DDR3A/B, ARM and PA PLL controllers have clkod register bits for
configuring postdiv values. So use it instead of using fixed
post dividers for these pll controllers. Assume that if fixed-postdiv
attribute is not present, use clkod register value for pistdiv.
Also update the Documentation of bindings to reflect the same.
Cc: Mike Turquette <mturquette@linaro.org
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Optional DT property to specify the desired parent clock for the McASP fck
clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The IP in DRA7xx is similar to the IP found in TI81xxAM3xxx/AM4xxx type of
SoCs but it is is integrated with sDMA instead of eDMA. The suitable pcm
driver for DRA7xx is the omap-pcm driver which is using dmaengine.
In the driver we can configure both dma related structures used for eDMA and
sDMA. The only thing we need to make sure that we set the correct dma_data
at startup with snd_soc_dai_set_dma_data()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
AM43xx have the same McASP IP as AM33xx and both platform uses eDMA. Modify
the Kconfig so it will be possible to add audio support for AM43xx based
boards later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7431798490 (of_spi: add generic binding support to specify cs gpio)
introduced generic binding for gpio chip-select. The cs_gpio struct field,
however, is an internal implementation detail of the Linux SPI subsystem, and
should not be mentioned in the device tree binding documentation. Mention the
previously defined cs-gpios master node property instead.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
