Again, Valleyview modes these around, so make the mmio base more
explicit to consolidate the base address computations to one
HAS_PCH_SPLIT check.
v2: Fix up the PCH_SPLIT braino ... it actually works that way round.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With valleyview we'll have these at yet another address, so keeping
track of this with an ever-growing list of registers will get ugly.
This way intel_sdvo.c is fully independent of the base address of the
output ports display register blocks.
While at it, do 2 closely related cleanups:
- use SDVO_NAME some more
- change the sdvo_reg variables to uint32_t like other registers.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They were all over the place, order them by position and add a few.
v2: add gen indications to the new bits (Ben)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we discard a buffer due to memory pressure, also release its alloted
mmap address space. As it may be sometime before userspace wakes up
and notices that it has buffers to purge from its cache, we may waste
valuable address space on unusable objects for a period of time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47738
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently i915 driver checks [PCH_]LVDS register bits to decide
whether to set up the dual-link or the single-link mode. This relies
implicitly on that BIOS initializes the register properly at boot.
However, BIOS doesn't initialize it always. When the machine is
booted with the closed lid, BIOS skips the LVDS reg initialization.
This ends up in blank output on a machine with a dual-link LVDS when
you open the lid after the boot.
This patch adds a workaround for that problem by checking the initial
LVDS register value in VBT.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=37742
Tested-By: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm main changes from Dave Airlie:
"This is the main drm pull request, I'm probably going to send two more
smaller ones, will explain below.
This contains a patch that is also in the fbdev tree, but it should be
the same patch, it added an API for hot unplugging framebuffer
devices, and I need that API for a new driver.
It also contains some changes to the i2c tree which Jean has acked,
and one change to moorestown platform stuff in x86.
Highlights:
- new drivers: UDL driver for USB displaylink devices, kms only,
should support correct hotplug operations.
- core: i2c speedups + better hotplug support, EDID overriding via
firmware interface - allows user to load a firmware for a broken
monitor/kvm from userspace, it even has documentation for it.
- exynos: new HDMI audio + hdmi 1.4 + virtual output driver
- gma500: code cleanup
- radeon: cleanups, CS optimisations, streamout support and pageflip
fix
- nouveau: NVD9 displayport support + more reclocking work
- i915: re-enabling GMBUS, finish gpu patch (might help hibernation
who knows), missed irq fixes, stencil tiling fixes, interlaced
support, aliasesd PPGTT support for SNB/IVB, swizzling for SNB/IVB,
semaphore fixes
As well as the usual bunch of cleanups and fixes all over the place.
I've got two things I'd like to merge a bit later:
a) AMD support for all their new radeonhd 7000 series GPU and APUs.
AMD dropped this a bit late due to insane internal review
processes, (please AMD just follow Intel and let open source guys
ship stuff early) however I don't want to penalise people who own
this hardware (since its been on sale for 3-4 months and GPU hw
doesn't exactly have a lifetime in years) and consign them to
using closed drivers for longer than necessary. The changes are
well contained and just plug into the driver new gpu functionality
so they should be fairly regression proof. I just want to give
them a bit of a run on the hw AMD kindly sent me.
b) drm prime/dma-buf interface code. This is just infrastructure
code to expose the dma-buf stuff to drm drivers and to userspace.
I'm not planning on pushing any driver support in this cycle
(except maybe exynos), but I'd like to get the infrastructure code
in so for the next cycle I can start getting the driver support
into the individual drivers. We have started driver support for
i915, nouveau and udl along with I think exynos and omap in
staging. However this code relies on the dma-buf tree being
pulled into your tree first since it needs the latest interfaces
from that tree. I'll push to get that tree sent asap.
(oh and any warnings you see in i915 are gcc's fault from what anyone
can see)."
Fix up trivial conflicts in arch/x86/platform/mrst/mrst.c due to the new
msic_thermal_platform_data() thermal function being added next to the
tc35876x_platform_data() i2c device function..
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (326 commits)
drm/i915: use DDC_ADDR instead of hard-coding it
drm/radeon: use DDC_ADDR instead of hard-coding it
drm: remove unneeded redefinition of DDC_ADDR
drm/exynos: added virtual display driver.
drm: allow loading an EDID as firmware to override broken monitor
drm/exynos: enable hdmi audio feature
drm/exynos: add default pixel format for plane
drm/exynos: cleanup exynos_hdmi.h
drm/exynos: add is_local member in exynos_drm_subdrv struct
drm/exynos: add subdrv open/close functions
drm/exynos: remove module of exynos drm subdrv
drm/exynos: release pending pageflip events when closed
drm/exynos: added new funtion to get/put dma address.
drm/exynos: update gem and buffer framework.
drm/exynos: added mode_fixup feature and code clean.
drm/exynos: add HDMI version 1.4 support
drm/exynos: remove exynos_mixer.h
gma500: Fix mmap frambuffer
drm/radeon: Drop radeon_gem_object_(un)pin.
drm/radeon: Restrict offset for legacy display engine.
...
Introduced in commits c1cd90ed and d27b1e0e
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: s/fix/shut up in the commit msg and add a comment to the
BUG_ON.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Sanybridge a few MI read/write commands only work when ppgtt is
enabled. Userspace therefore needs to be able to check whether ppgtt
is enabled. For added hilarity, you need to reset the "use global GTT"
bit on snb when ppgtt is enabled, otherwise it won't work. Despite
what bspec says about automatically using ppgtt ...
Luckily PIPE_CONTROL (the only write cmd current userspace uses) is
not affected by all this, as tested by tests/gem_pipe_control_store_loop.
Reviewed-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything is in place, only bind to the global gtt
when actually required. Patch split-up suggested by Chris Wilson.
Reviewed-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PIPE_CONTROL on snb needs global gtt mappings in place to workaround a
hw gotcha. No other commands need such a workaround. Luckily we can
detect a PIPE_CONTROL commands easily because they have a write_domain
= I915_GEM_DOMAIN_INSTRUCTION (and nothing else has that).
v2: Binding the target of such a reloc into the global gtt actually
works instead of binding the source, which is rather pointless ...
v3: Kill a superflous has_global_gtt_mapping assignement noticed by
Chris Wilson.
Reviewed-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And track the existence of such a binding similar to the aliasing
ppgtt case. Speeds up binding/unbinding in the common case where we
only need a ppgtt binding (which is accessed in a cpu coherent fashion
by the gpu) and no gloabl gtt binding (which needs uc writes for the
ptes).
This patch just puts the required tracking in place.
v2: Check that global gtt mappings exist in the error_state capture
code (with Chris Wilson's llc reloc patches batchbuffers are no longer
relocated as mappable in all situations, so this matters). Suggested
by Chris Wilson.
v3: Adapted to Chris' latest llc-reloc patches.
v4: Fix a bug in the i915 error state capture code noticed by Chris
Wilson.
Reviewed-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note that there's a functional change buried in this patch wrt the ilk
dmar workaround: We now only idle the gpu while tearing down the dmar
mappings, not while clearing the gtt. Keeping the current semantics
would have made for some really ugly code and afaik the issue is only
with the dmar unmapping that needs a fully idle gpu.
Reviewed-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* tag 'drm-intel-next-2012-03-01' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Only clear the GPU domains upon a successful finish
drm/i915: reenable gmbus on gen3+ again
drm/i915: i2c: unconditionally set up gpio fallback
drm/i915: merge gmbus and gpio i2c adpater into one
drm/i915: merge struct intel_gpio into struct intel_gmbus
i2c: export bit-banging algo functions
drm/nouveau: do a better job at hiding the NIH i2c bit-banging algo
drm/i915: add dev_priv to intel_gmbus
drm/i915: Fix single msg gmbus_xfers writes
drm/i915: error_buffer->ring should be signed
drm/i915: Silence the error message from i915_wait_request()
drm/i915: use the new hdmi_force_audio enum more
drm/i915: No need to search again after retiring requests
drm/i915: Only bump refcnt on objects scheduled for eviction
drm/i915/bios: Downgrade the "signature missing" DRM_ERROR to debug
drm/i915: Ignore LVDS on hp t5745 and hp st5747 thin client
drm/i915: Fixes distorted external screen image on HP 2730p
Use a more current logging style. Ensure that appropriate
logging messages are prefixed with "i915: ".
Convert printks to pr_<level>. Align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mark the Acer Aspire 5734Z that this machines requires the module to
invert the panel backlight brightness value after reading from and prior
to writing to the PCI configuration space.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A machine may need to invert the panel backlight brightness value. This
patch adds the infrastructure for a quirk to do so.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Following the documentation of the Legacy Backlight Brightness (LBB)
Register in the configuration space of some Intel PCI graphics adapters,
setting the LBB register with the value 0x0 causes the backlight to be
turned off, and 0xFF causes the backlight to be set to 100% intensity
(http://download.intel.com/embedded/processors/Whitepaper/324567.pdf).
The Acer Aspire 5734Z, however, turns the backlight off at 0xFF and sets
it to maximum intensity at 0. In consequence, the screen of this systems
becomes dark at an early boot stage which makes it unusable. The same
inversion applies to the BLC_PWM_CTL I915 register. This problem was
introduced in kernel version 2.6.38 when the PCI device of this system
was first supported by the i915 KMS module.
This patch adds a parameter to the i915 module to enable inversion of
the brightness variable (i915.invert_brightness).
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I have seen a number of "blt ring initialization failed" messages
where the ctl or start registers are not the correct value. Upon further
inspection, if the code just waited a little bit, it would read the
correct value. Adding the wait_for to these reads should eliminate the
issue.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some newer BIOSes are shipping with all MTRRs already populated. These
BIOSes are all on machines with sufficiently new CPUs that the
referenced errata doesn't apply anyway, so just don't try to claim the
MTRR.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41648
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_framebuffer_init does some basic sanity checking of the pixel format,
but is used by the plane code in addition to the primary crtc. So it
needs to contain any formats used in either place.
Add the XBGR8888 format to the checklist so the plane code can use it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
According to the PRM (Vol3P2), the PCH FDI receiver ISR read for bit lock
should be retried at least once. This patch retries the read 5 times
with a small delay in between reads. I've had reports of display corruption
on resume with "FDI train 1 fail!", so I'm hoping that adding this retry
will mitigate the issue.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're not really errors (well actually I don't know; I don't
understand _DSM and _MUX well enough to say, but I do know they spam
people's logs and seem to be harmless).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: The _DSM error got remove in another patch already]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44250
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This change enables the use of displays where the vbt table just
contains inappropriate values, but either the vesa defaults or
the video=... modes do something sensible with the attached display.
The problem happens with an embedded board that contains vbt bios
tables that do not match the attached display. Using this change and
the appropriate kernel boot command line they are able to use an
otherwise completely unusable secondary display on that embedded
board.
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Mathias Froehlich <Mathias.Froehlich@web.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the rework to merge the bit-banging fallback into the gmbus
i2c adapter we've gotten rid of the deadlock possibility that
originally lead to the disabling of this code.
This reverts the revert
commit 826c7e4147
Author: Jean Delvare <khali@linux-fr.org>
Date: Sat Jun 4 19:34:56 2011 +0000
Revert "drm/i915: Enable GMBUS for post-gen2 chipsets"
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=35572
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can simplify the setup and teardown a bit.
Because we don't actually allocate anything anymore for the force_bit
case, we can now convert that into a boolean.
Also and the functionality supported by the bit-banging together with
what gmbus can do, so that this doesn't randomly change any more.
v2: Chris Wilson noticed that I've mixed up && and & ...
v3: Clarify an if block as suggested by Eugeni Dodonov.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... and directly call the newly exported i2c bit-banging functions.
The code is still pretty convoluted because we only set up the gpio
i2c stuff when actually falling back, resulting in more complexity
than necessary. This will be fixed up in the next patch.
v2: Use exported i2c_bit_algo vtable instead of exported functions.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we set up the gpio fallback, we always have a 1:1 relationship
with an intel_gmbus. Exploit that to store all gpio related data in
there, too. This is a preparation step to merge the tw i2c adapters
controlling the same bus into one.
Just mundane code-munging in this patch.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can free up the bus->adaptor.algo_data pointer and make it
available for use with the bitbanging fallback algo.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gmbus_xfer with a single message (particularly a single message write) would
set Bus Cycle Select to 100b, the Gen Stop cycle, instead of 101b,
No Index, Stop cycle. This would not start single message i2c transactions.
Also, gmbus_xfer done: will disable the interface without checking if
it is idle. In the case of writes, there will be no wait on status or delay
to ensure the write starts and completes before the interface is turned off.
Fixed the former issue by using the same cycle selection as used in the
I2C_M_RD for the write case.
GMBUS_CYCLE_WAIT | (i + 1 == num ? GMBUS_CYCLE_STOP : 0)
Fixed the latter by waiting on GMBUS_ACTIVE to deassert before disable.
Note from the grumpy d-i-n maintainer: The first hunk that changes the
gmbus read path is just cosmetics to align the code with the write
path. I.e. the commit message above is slightly lying because the
first issue is _only_ with writes (and not simply "particularly").
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gcc seems to get uber-anal recently about these things.
Clarification from Dan Carpenter:
"Sorry, I should have said that it's not a gcc warning, it's a smatch
thing. But also it's not uber-anal. It's the exact level of anality
which is required to make the == -1 test work. You can compare
unsigned int and longs to -1 and it works but for smaller types it
doesn't."
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This error message has since been superseded by the hangcheck, and does
not add any salient information beyond that already printed by hangcheck
discovering the GPU hang that lead to i915_wait_request() bombing out in
the first place.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a revert of 6aa56062ea.
This was originally introduced to workaround reads of the ringbuffer
registers returning 0 on SandyBridge causing hangs due to ringbuffer
overflow. The root cause here was reads through the GT powerwell require
the forcewake dance, something we only learnt of later. Now it appears
that reading the reported head position from the HWS is returning
garbage, leading once again to hangs.
For example, on q35 the autoreported head reports:
[ 217.975608] head now 00010000, actual 00010000
[ 436.725613] head now 00200000, actual 00200000
[ 462.956033] head now 00210000, actual 00210010
[ 485.501409] head now 00400000, actual 00400020
[ 508.064280] head now 00410000, actual 00410000
[ 530.576078] head now 00600000, actual 00600020
[ 553.273489] head now 00610000, actual 00610018
which appears reasonably sane. In contrast, if we look at snb:
[ 141.970680] head now 00e10000, actual 00008238
[ 141.974062] head now 02734000, actual 000083c8
[ 141.974425] head now 00e10000, actual 00008488
[ 141.980374] head now 032b5000, actual 000088b8
[ 141.980885] head now 03271000, actual 00008950
[ 142.040628] head now 02101000, actual 00008b40
[ 142.180173] head now 02734000, actual 00009050
[ 142.181090] head now 00000000, actual 00000ae0
[ 142.183737] head now 02734000, actual 00009050
In addition, the automatic reporting of the head position is scheduled
to be defeatured in the future. It has no more utility, remove it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45492
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
While fixing up a merge conflict with drm-next I've noticed that we
use the same audio drm connector property also for dp and sdvo
outputs.
So put the new enum to some good use and convert these paths, too. The
HDMI_AUDIO_ prefix is a bit a misnomer. But at least for sdvo it makes
sense (and you can also connect a hdmi monitor with a dp->hdmi cable),
so I've decided to stick with it.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Retiring requests does not typically free up space in the aperture,
so the additional search is pointless.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Incrementing the reference count on all objects walked when searching
for space in the aperture is a non-neglible amount of overhead. In fact,
we only need to hold on to a reference for objects that we will evict,
so we can therefore delay the referencing until we find a suitable hole
and only add those objects that fall inside.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When setting overlay position with x<0, it will divide 0 and make drm
driver crash.
Signed-off-by: Hai Lan <hai.lan@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
