It is useful to assert that if the object is bound, then it must have
its pages pinned to prevent the shrinker from reaping its backing store.
This is even more useful with the introduction of real-ppgtt whereupon
we may have the object bound into several vma, with each instance
pinning the backing store. This assertion breaks down during unbind
where we unpinned the backing store before decoupling the vma binding.
This can be fixed with a trivial reording of the unbind sequence, which
reinforces the
pin pages
bind to vma
...
unbind from vma
unpin pages
concept.
v2: Bonus comment
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, FIFO will be shared by both SW and HW. So, we read the
free entries through register and update dev_priv variable
and wait for only 20 entries to be free
From Deepak's follow-up mail explaining why vlv is special:
"On SB, Out of 64 FIFO Entries, 20 Entries will be used by HW and
remaining 44 will be used by the SW,. I think due to this reason, we
have a threshold of 20 Entries."
"On VLV, HW and SW can access all 64 fifo entries, I don't think
having a threshold of 20 Entries is mandatory on VLV. Also, since both
SW and HW can access all 64 Entries. I think on VLV, we need to update
the fifo_count before waiting for the FIFO."
v2: Apply mask when we read the number of free FIFO entries (Ville).
v3: Mask applied after reading the register (Deepak).
Signed-off-by: Deepak S <deepak.s@intel.com>
[danvet: Add further explanation from Deepak to commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only plane A is FBC capable on gen2 (like gen3), but the panel fitter
is hooked up to pipe B, so we want to prefer pipe B + plane A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add the code comment Chris requested in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a REG_WRITE_FOOTER macro as a counterpart to the REG_WRITE_HEADER.
The current code has the spin_lock() in the HEADER, but the
spin_unlock() is open coded, which looks rather confusing on the first
glance. A bit of additional symmetry might help.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We call intel_modeset_setup_hw_state() along two paths, driver
load/resume and after a lid event notification. During initialisation of
the driver, it is imperative that we reset the config state. This
correctly sets up the initial connector statuses and prepares the
hardware for a thorough probing. However, during a lid event, we only
want to undo the damage caused by the bios by resetting our last known
mode. In this cirumstance, we do not want to clobber our desired state.
In order to try and keep sanity between the config state and our own
tracking, do the drm_mode_config_reset() first along the load/resume
paths before reading out the hw state and apply any definite known
corrections.
v2: "As discussed on irc I don't think we should force the connector
state to anything here: Imo connector->status should reflect what we
believe to be the true output connection state, whereas connector->encoder
reflects whether this connector is wired up to a pipe. And since we no
longer reject modeset on disconnected connectors and never nuked the pipe
if the connector gets disconnected there's no reason for that - such policy
is userspace's job.
This regression has been introduced in
commit 2e9388923e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 11 20:08:24 2012 +0200
drm/i915/crt: explicitly set up HOTPLUG_BITS on resume"
so sayeth Daniel.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org (v3.8 and later)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some lower level things get angry if we don't have modeset locks
during intel_modeset_setup_hw_state(). Actually the resume and
lid_notify codepaths alreday hold the locks, but the init codepath
doesn't, so fix that.
Note: This slipped through since we only disable pipes if the
plane/pipe linking doesn't match. Which is only relevant on older
gen3 mobile machines, if the BIOS fails to set up our preferred
linking.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Tested-and-reported-by: Paul Bolle <pebolle@tiscali.nl>
[danvet: Add note now that I could confirm my theory with the log
files Paul Bolle provided.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When inspecting reports that boot/suspend/resume times are unusual it
would be useful to clearly identify the time we must spend waiting for
the hardware to complete its task. In this case we have a notification
before we start waiting for the panel to change state, but none
afterwards - which would be useful.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Checkpatch tells me
WARNING: __packed is preferred over __attribute__((packed))
so switch over to __packed across the driver before adding new packed
structs.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check that the N and P dividers don't cause a divide by zero.
This shouldn't happen under normal circumstances, but can
happen eg. under simulation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's a pain for two reasons:
- The vga plane redisablign requires actual legacy vgao i/o to pull
of. The hw engineers really botched this one here :(
- There seem to be some BIOS out there which send out lid events when
unplugging. Together with our broken DP code, which disables the
port when the cable is lost, this results in an immediate modeset
call, which can hang on the wait for outstanding flips.
- Also we don't want to force a modeset on machines where it's not
really needed, see the referenced bug.
We might want to extend this in general to also all machines that
support opregion, since there the BIOS supposedly should manage the
gfx hardware more cooperatively.
v2: Pimp commit message a bit.
Cc: Roland Dreier <roland@kernel.org>
References: https://bugs.freedesktop.org/show_bug.cgi?id=65486
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During the vmap() routine for the dma-buf, we first grab the pages and
then try to allocate a temporary array to pass to the vmap(). However,
the shrinker can and will reap any object that is unbound if the
allocation for the array first fails. This includes the object which we
are attempting to vmap(). The solution is to mark the object's pages as
pinned whilst we try the allocation to prevent the use-after-free
introduced by the potential shrinkage.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're currently misprinting the port name when vlv_wait_port_ready()
times out. Fix it by using port_name().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The MI_PREDICATE_RESULT_2 register exits only on HSW. On other
platforms the same offset is either reserved, or contains some
other register. So write the register only on HSW.
This regression has been introduced in
commit 9435373ef8
Author: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Date: Wed Aug 28 16:45:46 2013 -0300
drm/i915: Report enabled slices on Haswell GT3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add regression notice.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ring scratch pages don't have a PPGTT mapping, so the DERRM SRM
should target the global GTT instead.
v2: Add MI_SRM_LRM_GLOBAL_GTT define for -fixes
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When I submitted the first patch adding these force wake functions,
Chris Wilson observed that I was using the wrong functions, so I sent
a second version of the patch to correct this problem. The problem is
that v1 was merged instead of v2.
I was able to notice the problem when running the
debugfs-forcewake-user subtest of pm_pc8 from intel-gpu-tools.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had some mode_valid() vfuncs returning an int, others the enum. Let's
use the latter everywhere.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we call intel_display_power_enabled() from
i915_capture_error_state() in IRQ context and then take a mutex. To fix
this add a new intel_display_power_enabled_sw() which returns the domain
state based on software tracking as opposed to reading the actual HW
state.
Since we use domain_use_count for this without locking on the reader
side make sure we increase the counter only after enabling all required
power wells and decrease it before disabling any of these power wells.
Regression introduced in
commit 1b02383464b4a915627ef3b8fd0ad7f07168c54c
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Sep 24 16:17:09 2013 +0300
drm/i915: support for multiple power wells
Note that atm we depend on the value returned by
intel_display_power_enabled_sw() in i915_capture_error_state() to avoid
unclaimed register access reports. This was never guaranteed though,
since another thread can disable the power concurrently. If this is a
problem we need another explicit way to disable the reporting during
error captures.
v2:
- remove barriers as the caller can't depend on the value
returned from i915_capture_error_state_sw() anyway (Ville)
- dump the state of pipe/transcoder power domain state (Daniel)
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV can have eDP on either port B or C, or even both. Based on the
VBT spec, intel_dpd_is_edp() should work on VLV too, assuming we
check the correct ports.
So instead of hardcoding port D, rename the function to
intel_dp_is_edp() and pass the port as a parameter, and use it
on VLV ports B and C.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71051
Tested-by: Robert Hooker <robert.hooker@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Wrestle the patch to apply and compile properly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use timeout mode, and we need to lower the timeout to get good RC6
residency when loads are running. This gets me from 0% residency during
glxgears to 77%, which is a pretty good improvement. This value also
matches the current BWG recommentations.
Tested-by: "Meng, Mengmeng" <mengmeng.meng@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Deepak S <deepak.s@inel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It leads to a big mess when stuff interleaves. Especially with the new
patch I've submitted for the drm core to no longer artificially split
up debug messages.
v2: The size parameter to snprintf includes the terminating 0, but the
return value does not. Adjust the logic accordingly. Spotted by Mika.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It doesn't like that we assign 0 to a pointer, it wants the real NULL.
On closer look that initialization is actually bogus, and the compiler
can easily see that we never use it unitialized. So let's just drop
this.
Cc: Deepak S <deepak.s@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV the GTFIFOCTL register has other bits besides the number of free
entries in the GT wake FIFO. Apply a mask when we read th register to
make sure we don't misinterpret the number of free FIFO entries.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: There's some unclarity about hsw, but brushed off as todays'
Bspec just acting up a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Split vlv force wake routines to help individually control Media/Render
well based on the register access.
We've seen power savings in the lower sub-1W range on workloads that
only need on of the power wells, e.g. glbenchmark, media playback
Note: The same split isn't there for the forcewake queue, only the
forcwake domains are split.
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Rebase on top of the removed forcewake hack in the ring irq
get/put code and add a note to add Deepak's answer to Chris question.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added power well arguments to all the force wake routines
to help us individually control power well based on the
scenario.
Signed-off-by: Deepak S <deepak.s@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with the removed forcewake hack and drop one
spurious hunk Jesse noticed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This value is more correct, and matches what we read out in the fastboot
code. Without this, the watermark code will panic after the first mode
setting activity after a fastboot.
v2: fix up HSW ->clock usage too (Ville)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to user fudging (for instance using video=VGA-1:e with FBDEV=n) we can
attempt to reset an inconsistent CRTC that is marked as active but has
no assigned fb. It would be wise to fix this earlier, but the long
term plan is to have primary and secondary planes associated with a
CRTC, in which crtc->fb being NULL will be expected. So for a quick
short term fix with pretensions of grandeur, just check for a NULL fb
during GPU reset and ignore the plane restoration.
This fixes a potential hard hang (a panic in the panic handler)
following a GPU hang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Add a corresponding fixme comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As the execbuffer dispatch grows ever more complex and involves multiple
stages of moving objects into the aperture, we need to take greater care
that we do not evict our execbuffer objects prior to dispatch. This is
relatively simple as we can just keep the objects pinned for not just
the relocation but until we are finished.
One such example is the possibility of the context switch causing an
eviction or hitting the shrinker in order to fit its object into the
aperture.
Link: http://lists.freedesktop.org/archives/intel-gfx/2013-November/036166.html
Reported-by: "Siluvery, Arun" <arun.siluvery@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add the additional explanations from Chris to the commit
message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a debugfs entry showing the use-count for all power domains of each
power well.
v3: address comments from Paulo:
- simplify power_domain_str() by using a switch table
- move power_well::domain_count to power_domains
- WARN_ON decrementing a 0 refcount
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far we distinguished platforms without a dynamic power well with
the HAS_POWER_WELL macro and for such platforms we didn't call any power
domain functions. Instead of doing this check we can add an always-on
power well for these platforms and call the power domain functions
unconditionally. For always-on power wells we only increase/decrease
their refcounts, otherwise they are nop.
This makes high level driver code more readable and as a bonus provides
some idea of the current power domains state for all platforms (once
the relevant debugfs entry is added).
v3: rename intel_power_wells to i9xx_always_on_power_well (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This may need work if other platforms do the same thing, but in the
meantime we should avoid looking at HSW specific bits in this generic
function.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[added IS_BROADWELL too as that needs the same handling (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
[danvet: Add Imre's missing sob.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In intel_display_capture_error_state we use HAS_POWER_WELL to check if
we are running on Haswell/Broadwell when accessing HSW_PWR_WELL_DRIVER
which is specific to these platforms. Future platforms with power wells
don't have this register, so HAS_POWER_WELL won't work there any more.
Use IS_HASWELL/IS_BROADWELL instead.
v3: fix using logical || instead of bitwise | (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of using a separate function to check whether a power domain is
is always on, add an always-on power well covering all these power
domains and do the usual get/put on these unconditionally. Since we
don't assign a .set handler for these the get/put won't have any effect
besides the adjusted refcount.
This makes the code more readable and provides debug info also on the
use of always-on power wells (once the relevant debugfs entry is added.)
v3: make is_always_on to be bool instead of a bit field (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HW generations so far had only one always-on power well and optionally
one dynamic power well. Upcoming HW gens may have multiple dynamic power
wells, so add some infrastructure to support them.
The idea is to keep the existing power domain API used by the rest of
the driver and create a mapping between these power domains and the
underlying power wells. This mapping can differ from one HW to another
but high level driver code doesn't need to know about this. Through the
existing get/put API it would just ask for a given power domain and the
power domain framework would make sure the relevant power wells get
enabled in the right order.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way the code is simpler and can also be used for other platforms
where the audio power domain->power well mapping is different.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
