Add code to issue CONFIG_DEV "get" firmware command.
This command is used in order to obtain certain parameters used for
supporting various RX checksumming options and vxlan UDP port.
The GET operation is allowed for VFs too.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed in order to get cache cold pages (L3 flushed) for HW scatter.
Otherwise memory may flush those entries when the packet comes from
PCI, causing back pressure resulting in BW decrease.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP_ALIGN has a non zero value, hardware will write to a non aligned
address. The only reader from this address is when copying the header
from the first frag into the linear buffer (further access to the IP
address will be from the linear buffer, in which the headers are
aligned). Since the penalty of non align access by the hardware is
greater than the software memcpy, changing the frag_align to always be 0.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to protect set_port_type() for concurrency, as the sysfs code could
call it from mutliple contexts in parallel.
The port_mutex is not enough because we need to protect from concurrent
modification of 'info' and stopping of the port sensing work.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added wrapper to the ACCESS_REG command for handling guest HW
registers access, preventing write operations, but do allow reads.
This will prevent SRIOV guests to change port PTYS configuration,
such as speed/advertised link modes.
Fixes: adbc7ac5c1 ('net/mlx4_core: Introduce ACCESS_REG CMD [...]')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.
Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231
CC: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix a few problems with our parsing of the MDET registers:
* Queue IDs are longer than 8 bits
* Queue IDs are absolute for the device and the base queue must be
subtracted out.
* VF IDs are longer than 8 bits
* Use the MASK define to mask the event value, instead of the SHIFT
define.
Change-ID: I3dc7237f480c02e1192a2a8ea782f8a02ab2a8b7
Reported-by: Marc Neustadter <marc.neustadter@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are more cores than vectors available to the PF, scale back
the LAN msix usage to force queue/vector sharing and leave some vectors
for Flow Director, VMDq, etc.
Change-ID: Ie0317732eb85ad8d851d7da7d9af86b1bf8c21ad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The debugfs dump stats wasn't being kept up-to-date, was redundant with
the ethtool output, and didn't offer any useful additional info. Rather
than continue trying to keep them aligned, just remove the debugfs command.
Change-ID: Id130ed9aef01c6369ab662c7b4c5ec5b1dbc5b40
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <Jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to irq_dynamic_disable was turning off the interrupt completely
when trying to set ITR to 0 (for lowest moderation). Just remove the
call as setting the values to 0 later in this function will suffice.
Change-ID: I47caf1ecbe65653cf63ec833db93094cd83fd84d
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the interface is closed, but VFs exist, current code will spam all
the VFs with link messages every second. This is because the link event
code was looking at netif_carrier_ok() without checking to see if the
interface was actually open.
Refactor the logic to only check the carrier state if the interface is
actually open. This allows link changes to be reported correctly without
spamming the VFs.
Change-ID: If136e79bb3820d21ea4e39e332e8a9604efc2b2a
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we receive an admin queue message, the msg_size field in the event
struct gets overwritten. Because of this, we need to reinit the field
each time we go through the loop. Without this we may receive truncated
messages due to the firmware thinking we have insufficient buffer size.
Change-ID: I21dcca5114d91365d731169965ce3ffec0e4a190
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets the reset state channels accoridng at86rf2xx datasheets.
We don't need to set the default page here which is zero on all chips.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit e37d2ec82a ("mac802154: ops:
declare channel and page as u8") the page parameter can't be below zero.
This patch fix a kbuild test robot warning. Furthermore this check
should be removed and handled by netlink 802.15.4 interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMC91x is written to explicitly look up the IRQ resource
from the platform device and extract the IRQ and flags, however
the platform_get_irq() does additional things, like call
of_irq_get() in the device tree case, which will translate
the IRQ using the irqdomain and defer the probe if the
IRQ host cannot be found.
As we're not looking up the resource, this will not retrieve
the IRQ flags, but that is better done using
irqd_get_trigger_type(), as the trigger is what the driver
wants to modify. We take care to preserve the semantics that
will make the trigger type provided from the resource
override any local specifier.
Tested on the Nomadik NHK15 which has its SMC91x IRQ line
connected to a STMPE2401 GPIO expander on I2C.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When use current latest upstream qemu (current version: 2.1.2), need let
driver compatible with 'xlnx,xps-ethernetlite-2.00.b', or can not find
net device in microblaze qemu. Related QEMU commands under fedora 20:
yum install libvirt
yum install tunctl
tunctl -b
ip link set tap0 up
brctl addif virbr0 tap0
./microblaze-softmmu/qemu-system-microblaze -M petalogix-s3adsp1800 \
-kernel ../linux-stable.microblaze/arch/microblaze/boot/linux.bin \
-no-reboot -append "console=ttyUL0,115200 doreboot" -nographic \
-net nic,vlan=0,model=xlnx.xps-ethernetlite,macaddr=00:16:35:AF:94:00 \
-net tap,vlan=0,ifname=tap0,script=no,downscript=no
in microblaze qemu bash (guest machine):
ifconfig eth0 add 192.168.122.2 netmask 255.255.255.0
ifconfig eth0 up
After add this patch, can find the device, and can be used by 'telnetd'
(need cross-build busybox with glibc for it), then outside can telnet to
it without password.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of bcm_sysport_init_tx_ring() can currently fail, and will
always call bcm_sysport_fini_tx_ring() in a loop ending at the number of
TX queues (32) without checking if the TX ring was successfully
initialized or not.
Update bcm_sysport_fini_tx_ring() to return early and avoid a crash
de-referencing ring->cbs if the TX ring was not initialized, since
ring->cbs is the last part of the initialization done by
bcm_sysport_init_tx_ring() that could fail.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be allocating a single byte of DMA coherent memory, but
instead a full-sized struct dma_desc (8 bytes).
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we are allocating memory using kzalloc for struct mvpp2_prs_entry,
but later when we are getting error we were just returning the error
value without releasing the memory.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-10-31
Please pull this small batch of spooky fixes intended for the 3.18
stream...boo!
Cyril Brulebois adds an rt2x00 device ID.
Dan Carpenter provides a one-line masking fix for an ath9k debugfs
entry.
Larry Finger gives us a package of small rtlwifi fixes which add some
bits that were left out of some feature updates that were included
in the merge window. Hopefully this isn't a sign that the rtlwifi
base is getting too big...
Marc Yang brings a fix for a temporary mwifiex stall when doing 11n
RX reordering.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
0d961b3b52 (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
0d961b3b52 (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_print_status() to report a change in the PHY status.
The current message is not verbose enough, so this commit improves
it by using the generic status message.
After this change, the kernel reports PHY status down and up events as:
mvneta f1070000.ethernet eth0: Link is Down
mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3b57de958e brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast and ucast filter entries)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Because bonding stats are usually sum of slave stats, it was
not easy to account for tx drops at bonding layer.
We can use dev->tx_dropped for this, as this counter is later
added to the device stats (in dev_get_stats())
This extends the idea we had in commit ee63771474 ("bonding: Simplify
the xmit function for modes that use xmit_hash") for bond_3ad_xor_xmit()
to other bonding modes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add cfg80211 dump_survey handler for mwifiex.
This handler will be called to report channel statistics
to cfg80211.
This in turn adds ACS support for mwifiex AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to record channel statistics during
scan. With extended scan, scan results are returned as events from
FW while channel statistics are part of scan command response.
We store these channel statistics in adapter.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.
[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting old radio via HWSIM_CMD_DEL_RADIO then listeners on the
multicast group "config" are informed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding new radio via HWSIM_CMD_NEW_RADIO then listeners on the
multicast group "config" are informed.
While at it, refactor the configuration parameters to be able to
pass them directly and have fewer function arguments.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix my mistake while sending Johannes's
commit aadede6e9f
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Oct 9 17:01:36 2014 +0200
iwlwifi: mvm: port to devcoredump framework
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These drivers now call ipv6_proxy_select_ident(), which is defined
only if CONFIG_INET is enabled. However, they have really depended
on CONFIG_INET for as long as they have allowed sending GSO packets
from userland.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: f43798c276 ("tun: Allow GSO using virtio_net_hdr")
Fixes: b9fb9ee07e ("macvtap: add GSO/csum offload support")
Fixes: 5188cd44c5 ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets")
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases hw recovery was taking an absurdly
long time due to ath10k waiting for things that
would never really complete.
Instead of waiting for inevitable timeouts poke
all completions and wakequeues and check if it's
still worth waiting.
Reading/writing ar->state requires conf_mutex.
Since waiters might be holding it introduce a new
flag CRASH_FLUSH so it's possible to tell waiters
to abort whatever they were waiting for.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now it was possible to simulate soft and
hard fw crashes but it wasn't possible to trigger
an immediately hw restart itself (without the fw
crash).
This can be useful when stress testing hw
restarting stability, e.g. during heavy tx/rx
traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While testing other things I've found that CE
items aren't cleared properly. This could lead to
null dereferences in BMI.
To prevent that make sure CE revoking clears the
nbytes value (which is used as a buffer completion
indication) and memset the entire CE ring data
shared between host and target when
(re)initializing.
Also make sure to check BMI xfer pointer and print
a splat instead of crashing the kernel.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently hif_power_up performs effectively a
reset and hif_stop resets the chip as well so
there's no point in resetting here.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power up procedure was overly complex due to
warm/cold reset workarounds and issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
