[WHAT & HOW]
- Populate dml 2 callback with get_max_flickerless_instant_vtotal_increase
- Use long long when necessary to prevent overflow
- Add asic specific default values, currently disabled by
default for every asic
- Use the pre-existing debug option to protect the call to
get_max_flickerless_instant_vtotal_increase
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Bitnun <etbitnun@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW for DCN401 is presented with a small I2C speed fluctuation that
exceeds the hard cap limitation of 100kHz occasionally. This violates
compliance requirement and will result in failure in compliance.
[HOW]
After various measurements and traceback to previous generation HW, DCN IP,
SI and SW driver agrees that we can reduce I2C speed to 95kHz to address
the I2C spped fluctuation in DCN401.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DML2.1 has added the support to determine ODM combine based on DSC slice
count limitation. This support would allow us to support DSC slice higher
than 4 on small timings. The change will allow higher DSC slice support
independent from pixel clock in use.
[HOW]
Add a DCN401 get_enc_caps function to allow the support for DSC slice count
higher than 4.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Fast updates can consist of some stream updates as well (i.e., out_csc).
In these cases we should not offload the flip to FW as we can only
offload address only updates to FW.
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
UHBR13.5 support is optional, even if UHBR20 is supported by the device.
If source supports max UHBR13.5 while sink, cable and LTTPR support
UHBR20 but not UHBR13.5, UHBR10 should be used as the max link cap.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently 3-tap chroma subsampling is used for YCbCr422/420. When ODM
pipesplit is used, pixels on the left edge of ODM slices need one extra
pixel from the right edge of the previous slice to calculate the correct
chroma value.
Without this change, the chroma value is slightly different than
expected. This is usually imperceptible visually, but it impacts test
pattern CRCs for compliance test automation.
[HOW]
Update logic to use the register for adding extra left edge pixel for
YCbCr422/420 ODM cases.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The CONNECTOR_ID_USBC check was removed to fix a regression, but it was
re-introduced by accident. This commit drops the USBC that causes the
regressions.
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If there are no DC clock limits present, or if the DC limits are the same
as the AC limits, we can disable the AC/DC codepath as there won't be any
validation differences between the two modes.
[HOW]
When all DC power mode clock limits are the same as the max clock
values, there won't be any difference between AC mode and DC mode. Zero
out DC limits that equal max and provide a new cap to indicate the
presence of any non-zero DC mode limit. In summary:
- zero out DC limits that are the same as max clock value
- new dc cap to indicate the presence of DC mode limits
- set limits present if any clock has distinct AC and DC values from SMU
Acked-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix some problems reported by Coverity
- Fix idle optimization checks for multi-display and dual eDP
- Fix incorrect size calculation for loop
- Fix DSC-re-computing
- Add Replay capability and state in debugfs
- Refactor DCCG into component folder
- Refactor input mode programming for DIG FIFO
- Reset DSC clock in post unlock update
- Clean-up recout calculation for visual confirm
- Enable urgent latency adjustments for DCN35
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Switching between DSC clock or disable DSC block are not double buffered update.
Corruption is observed if these updates happen before DSC double buffered
disconnection.
[how]
Move DSC disable and refclk reset to post unlock update. Wait for DSC double buffered
disconnection and all mpccs are disconnected before reset DSC clock.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow occurs when running Netflix in a 4k144 eDP + 4k60 HDMI FRL
setup. It is caused by latency varying based on the DCFCLK/FCLK state.
[How]
Enable urgent latency adjustment and match the reference to existing
ASIC that also see increased latency at low FCLK.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Input mode for the DIG FIFO should be programmed as part of stream
encoder setup.
[HOW]
Pre-calculate the pixels per cycle as part of the pixel clock params,
and program as part of stream encoder setup.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Providing a mechanism to manipulate the pwm frequency on the
individual GPUs and monitor the transition during the switch.
[How]
Added a variable in dc_debug_options data structure. Using
this variable to call the newly added command on the firmware.
Reviewed-by: Harry Vanzylldejong <harry.vanzylldejong@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sreeja Golui <sreeja.golui@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The assignment of disp_cfg_index_max is missed and should be
assigned to __DML2_WRAPPER_MAX_STREAMS_PLANES__.
Fixes: 55ec7679e6 ("drm/amd/display: Limit array index according to architecture")
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Make sure vmid0p72_idx, vnom0p8_idx and vmax0p9_idx calculation will
never overflow and exceess array size.
This fixes 3 OVERRUN and 1 INTEGER_OVERFLOW issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_clk_table->entries has size of MAX_NUM_DPM_LVL(=8), but the loop
counter i can go up to DML_MAX_CLK_TABLE_SIZE(=20) - 1.
[How]
The loop should be min(DML_MAX_CLK_TABLE_SIZE, MAX_NUM_DPM_LVL) - 1
instead.
This fixes 21 OVERRUN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For addtion (uint8_t) variable + constant 1,
coverity generates message below:
Truncation due to cast operation on "cur_idx + 1" from
32 to 8 bits.
Then Coverity assume result is 32 bits value be saved into
8 bits variable. When result is used as index to access
array, Coverity suspects index invalid.
[How]
Change varaible type to uint32_t.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
ctx->architecture determine array sizes of ODMMode and DPPPerSurface
arrays to __DML2_WRAPPER_MAX_STREAMS_PLANES__ or __DML_NUM_PLANES__,
and these array index should be checked before used
This fixes 2 OVERRUN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Coverity reports OVERRUN warning for
CalculateSwathAndDETConfiguration_params->hw_debug5
= &s->dummy_boolean[2].
bool dummy_boolean[2] is defined within
struct dml2_core_calcs_mode_support_locals.
[How]
Change array size from 2 to 3.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
dc->links[] has max size of MAX_LINKS and NULL is return when trying to
access with out-of-bound index.
This fixes 3 OVERRUN and 1 RESOURCE_LEAK issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
