The internal_hpd flag is set to true by dp_bridge_hpd_enable() and set to
false by dp_bridge_hpd_disable() to handle GPIO pinmuxed into DP controller
case. HDP related interrupts can not be enabled until internal_hpd is set
to true. At current implementation dp_display_config_hpd() will initialize
DP host controller first followed by enabling HDP related interrupts if
internal_hpd was true at that time. Enable HDP related interrupts depends on
internal_hpd status may leave system with DP driver host is in running state
but without HDP related interrupts being enabled. This will prevent external
display from being detected. Eliminated this dependency by moving HDP related
interrupts enable/disable be done at dp_bridge_hpd_enable/disable() directly
regardless of internal_hpd status.
Changes in V3:
-- dp_catalog_ctrl_hpd_enable() and dp_catalog_ctrl_hpd_disable()
-- rewording ocmmit text
Changes in V4:
-- replace dp_display_config_hpd() with dp_display_host_start()
-- move enable_irq() at dp_display_host_start();
Changes in V5:
-- replace dp_display_host_start() with dp_display_host_init()
Changes in V6:
-- squash remove enable_irq() and disable_irq()
Fixes: cd198cadde ("drm/msm/dp: Rely on hpd_enable/disable callbacks")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Leonard Lausen <leonard@lausen.nl> # on sc7180 lazor
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/1684878756-17830-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
The DP AUX interrupt handling was a bit of a mess.
* There were two functions (one for "native" transfers and one for
"i2c" transfers) that were quite similar. It was hard to say how
many of the differences between the two functions were on purpose
and how many of them were just an accident of how they were coded.
* Each function sometimes used "else if" to test for error bits and
sometimes didn't and again it was hard to say if this was on purpose
or just an accident.
* The two functions wouldn't notice whether "unknown" bits were
set. For instance, there seems to be a bit "DP_INTR_PLL_UNLOCKED"
and if it was set there would be no indication.
* The two functions wouldn't notice if more than one error was set.
Let's fix this by being more consistent / explicit about what we're
doing.
By design this could cause different handling for AUX transfers,
though I'm not actually aware of any bug fixed as a result of
this patch (this patch was created because we simply noticed how odd
the old code was by code inspection). Specific notes here:
1. In the old native transfer case if we got "done + wrong address"
we'd ignore the "wrong address" (because of the "else if"). Now we
won't.
2. In the old native transfer case if we got "done + timeout" we'd
ignore the "timeout" (because of the "else if"). Now we won't.
3. In the old native transfer case we'd see "nack_defer" and translate
it to the error number for "nack". This differed from the i2c
transfer case where "nack_defer" was given the error number for
"nack_defer". This 100% can't matter because the only user of this
error number treats "nack defer" the same as "nack", so it's clear
that the difference between the "native" and "i2c" was pointless
here.
4. In the old i2c transfer case if we got "done" plus any error
besides "nack" or "defer" then we'd ignore the error. Now we don't.
5. If there is more than one error signaled by the hardware it's
possible that we'll report a different one than we used to. I don't
know if this matters. If someone is aware of a case this matters we
should document it and change the code to make it explicit.
6. One quirk we keep (I don't know if this is important) is that in
the i2c transfer case if we see "done + defer" we report that as a
"nack". That seemed too intentional in the old code to just drop.
After this change we will add extra logging, including:
* A warning if we see more than one error bit set.
* A warning if we see an unexpected interrupt.
* A warning if we get an AUX transfer interrupt when shouldn't.
It actually turns out that as a result of this change then at boot we
sometimes see an error:
[drm:dp_aux_isr] *ERROR* Unexpected DP AUX IRQ 0x01000000 when not busy
That means that, during init, we are seeing DP_INTR_PLL_UNLOCKED. For
now I'm going to say that leaving this error reported in the logs is
OK-ish and hopefully it will encourage someone to track down what's
going on at init time.
One last note here is that this change renames one of the interrupt
bits. The bit named "i2c done" clearly was used for native transfers
being done too, so I renamed it to indicate this.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/520658/
Link: https://lore.kernel.org/r/20230126170745.v2.1.I90ffed3ddd21e818ae534f820cb4d6d8638859ab@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The source device should ensure the sink is ready before proceeding to
read the sink capability or perform any aux transactions. The sink
will indicate its readiness by asserting the HPD line. The controller
driver needs to wait for the hpd line to be asserted by the sink before
it performs any aux transactions.
The eDP sink is assumed to be always connected. It needs power from the
source and its HPD line will be asserted only after the panel is powered
on. The panel power will be enabled from the panel-edp driver and only
after that, the hpd line will be asserted.
Whereas for DP, the sink can be hotplugged and unplugged anytime. The hpd
line gets asserted to indicate the sink is connected and ready. Hence
there is no need to wait for the hpd line to be asserted for a DP sink.
Signed-off-by: Sankeerth Billakanti <quic_sbillaka@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/483312/
Link: https://lore.kernel.org/r/1650887072-16652-4-git-send-email-quic_sbillaka@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Widebus feature will transmit two pixel data per pixel clock to interface.
This feature now is required to be enabled to easy migrant to higher
resolution applications in future. However since some legacy chipsets
does not support this feature, this feature is enabled by setting
wide_bus_en flag to true within msm_dp_desc struct.
changes in v2:
-- remove compression related code from timing
-- remove op_info from struct msm_drm_private
-- remove unnecessary wide_bus_en variables
-- pass wide_bus_en into timing configuration by struct msm_dp
Changes in v3:
-- split patch into 3 patches
-- enable widebus feature base on chip hardware revision
Changes in v5:
-- DP_INTF_CONFIG_DATABUS_WIDEN
Changes in v6:
-- static inline bool msm_dp_wide_bus_enable() in msm_drv.h
Changes in v7:
-- add Tested-by
Changes in v9:
-- add wide_bus_en to msm_dp_desc
Changes in v10:
-- add wide_bus_en boolean to dp_catalog struc to avoid passing it as parameter
Changes in v11:
-- add const to dp_catalog_hw_revision()
-- add const to msm_dp_wide_bus_available()
Changes in v12:
-- dp_catalog_hw_revision(const struct dp_catalog *dp_catalog)
-- msm_dp_wide_bus_available(const struct msm_dp *dp_display)
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/476283/
Link: https://lore.kernel.org/r/1645824192-29670-5-git-send-email-quic_khsieh@quicinc.com
[DB: fixed the compilation]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Some DP sinkers prefer to use tps4 instead of tps3 during training #2.
This patch will use tps4 to perform link training #2 if sinker's DPCD
supports it.
Changes in V2:
-- replace dp_catalog_ctrl_set_pattern() with dp_catalog_ctrl_set_pattern_state_bit()
Changes in V3:
-- change state_ctrl_bits type to u32 and pattern type to u8
Changes in V4:
-- align } else if { and } else {
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1642531648-8448-4-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DP compo phy have to be enable to start link training. When
link training failed phy need to be disabled so that next
link traning can be proceed smoothly at next plug in. This
patch de-initialize mainlink to disable phy if link training
failed. This prevent system crash due to
disp_cc_mdss_dp_link_intf_clk stuck at "off" state. This patch
also perform checking power_on flag at dp_display_enable() and
dp_display_disable() to avoid crashing when unplug cable while
display is off.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
During suspend, dp host controller and hpd block are disabled due to
both ahb and aux clock are disabled. Therefore hpd plug/unplug interrupts
will not be generated. At dp_pm_resume(), reinitialize both dp host
controller and hpd block so that hpd plug/unplug interrupts will be
generated and handled by driver so that hpd connection state is updated
correctly. This patch will fix link training flaky issues.
Changes in v2:
-- use container_of to cast correct dp_display_private pointer
at both dp_pm_suspend() and dp_pm_resume().
Changes in v3:
-- replace hpd_state atomic_t with u32
Changes in v4
-- call dp_display_host_deinit() at dp_pm_suspend()
-- call dp_display_host_init() at msm_dp_display_enable()
-- fix phy->init_count unbalance which causes link training failed
Changes in v5
-- add Fixes tag
Fixes: 8ede2ecc3e (drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets)
Tested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Introduce audio support for Display Port on MSM chipsets.
This change integrates DP audio sub-module with the main
Display Port platform driver.
In addition, this change leverages hdmi_codec_ops to expose
the operations to the audio driver.
Changes in v2: fix up a compilation issue on drm-next branch
Changes in v3: none
Changes in v4: none
Changes in v5: none
Changes in v6: rebase on top of latest patchset of dependency
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Configure HPD registers in DP controller and
enable HPD interrupt.
Add interrupt to handle HPD connect and disconnect events.
Changes in v8: None
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
