Based on the Allwinner H5 datasheet and the pinctrl driver of the
backward-compatible H3 this introduces the pin multiplex assignments for
the H5 SoC.
H5 introduced some more pin functions (e.g. three more groups of TS
pins, and one more groups of SIM pins) than H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing compatible id for Exynos3250 SoC to device tree docs.
Exynos pin control driver supports it since commit d97f5b9804
("pinctrl: exynos: Add driver data for Exynos3250").
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SoC family such as DRA7 family of processors have, in addition
to the regular muxing of pins (as done by pinctrl-single), a separate
hardware module called IODelay which is also expected to be configured.
The "IODelay" module has it's own register space that is independent
of the control module and the padconf register area.
With recent changes to the pinctrl framework, we can now support
this hardware with a reasonably minimal driver by using #pinctrl-cells,
GENERIC_PINCTRL_GROUPS and GENERIC_PINMUX_FUNCTIONS.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay reconfiguration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do as little of muxing as absolutely necessary
without I/O isolation (which can only be done in initial stages of
bootloader).
NOTE: with the system wide I/O isolation scheme present in DRA7 SoC
family, it is not reasonable to do stop all I/O operations for every
such pad configuration scheme. So, we will let it glitch when used in
this mode.
Even with the above limitation, certain functionality such as MMC has
mandatory need for IODelay reconfiguration requirements, depending on
speed of transfer. In these cases, with careful examination of usecase
involved, the expected glitch can be controlled such that it does not
impact functionality.
In short, IODelay module support as a padconf driver being introduced
here is not expected to do SoC wide I/O Isolation and is meant for
a limited subset of IODelay configuration requirements that need to
be dynamic and whose glitchy behavior will not cause functionality
failure for that interface.
IMPORTANT NOTE: we take the approach of keeping LOCK_BITs cleared
to 0x0 at all times, even when configuring Manual IO Timing Modes.
This is done by eliminating the LOCK_BIT=1 setting from Step
of the Manual IO timing Mode configuration procedure. This option
leaves the CFG_* registers unprotected from unintended writes to the
CTRL_CORE_PAD_* registers while Manual IO Timing Modes are configured.
This approach is taken to allow for a generic driver to exist in kernel
world that has to be used carefully in required usecases.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: updated to use generic pinctrl functions, added
binding documentation, updated comments]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Marvell mv88f6180 mpp pins range from 0 to 19 as well as from 35 to 44.
This is already fixed in commit: 9573e79230
This is the documentation change for above commit.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g5 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms and the AST2500 evaluation board.
Now, update the bindings document to reflect the complete functionality
and implement the necessary pin configuration tables in the driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g4 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms. Now, update the bindings document
to reflect the complete functionality and implement the necessary pin
configuration tables in the driver.
Cc: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The System Control Unit IP block in the Aspeed SoCs is typically where
the pinmux configuration is found, but not always. A number of pins
depend on state in one of LPC Host Control (LHC) or SoC Display
Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
means to adjust these as necessary.
We use syscon to cast a regmap over the GFX and LPC blocks, which is
used as an arbitration layer between the relevant driver and the pinctrl
subsystem. The regmaps are then exposed to the SoC-specific pinctrl
drivers by phandles in the devicetree, and are selected during a mux
request by querying a new 'ip' member in struct aspeed_sig_desc.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
Pull pinctrl updates from Linus Walleij:
"Bulk pin control changes for the v4.10 kernel cycle:
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and reimagined as
a pin control driver with GPIO support in a joint effort by three
independent users of this hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control bindings
rather than the sunxi-specific. Add debouncing support to the
driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over to use
the generic GPIOLIB_IRQCHIP"
* tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits)
pinctrl: sx150x: use new nested IRQ infrastructure
pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505
pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced'
pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147]
pinctrl: mt8173: set GPIO16 to usb iddig mode
pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP
pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf
devicetree: bindings: pinctrl: Add binding for ti,da850-pupd
Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition
pinctrl: intel: set default handler to be handle_bad_irq()
pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507
pinctrl: sx150x: sort chips by part number
pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508)
pinctrl: imx: fix imx_pinctrl_desc initialization
pinctrl: sx150x: support setting multiple pins at once
pinctrl: sx150x: various spelling fixes and some white-space cleanup
pinctrl: mediatek: use builtin_platform_driver
pinctrl: stm32: use builtin_platform_driver
pinctrl: sunxi: Testing the wrong variable
pinctrl: nomadik: split up and comments MC0 pins
...
Pull GPIO updates from Luinus Walleij:
"Bulk GPIO changes for the v4.10 kernel cycle:
Core changes:
- Simplify threaded interrupt handling: instead of passing numbed
parameters to gpiochip_irqchip_add_chained() we create a new call:
gpiochip_irqchip_add_nested() so the two types are clearly
semantically different. Also make sure that all nested chips call
gpiochip_set_nested_irqchip() which is necessary for IRQ resend to
work properly if it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so that
anything != 0 will be send down to the driver as "1" not the value
passed in.
- ACPI can now support naming of GPIO lines, hogs and holes in the
GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem and was
moved over to a combined GPIO+pinctrl driver in the pinctrl
subsystem.
New features:
- Various cleanups to various drivers"
* tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits)
gpio: merrifield: Implement gpio_get_direction callback
gpio: merrifield: Add support for hardware debouncer
gpio: chardev: Return error for seek operations
gpio: arizona: Tidy up probe error path
gpio: arizona: Remove pointless set of platform drvdata
gpio: pl061: delete platform data handling
gpio: pl061: move platform data into driver
gpio: pl061: rename variable from chip to pl061
gpio: pl061: rename state container struct
gpio: pl061: use local state for parent IRQ storage
gpio: set explicit nesting on drivers
gpio: simplify adding threaded interrupts
gpio: vf610: use builtin_platform_driver
gpio: axp209: use correct register for GPIO input status
gpio: stmpe: fix interrupt handling bug
gpio: em: depnd on ARCH_SHMOBILE
gpio: zx: depend on ARCH_ZX
gpio: x86: update config dependencies for x86 specific hardware
gpio: mb86s7x: use builtin_platform_driver
gpio: etraxfs: use builtin_platform_driver
...
GPIO7 is configured in POWERHOLD mode which has higher priority
over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON
bit is turned off. This property enables driver to over ride the
POWERHOLD value to GPIO7 so as to turn off the PMIC in power off
scenarios.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add #pinctrl-cells for pinctrl-single using dts files. This allows
us to use generic parser later on. Note that the driver supports
handling the legacy binding also with no #pinctrl-cells so these
changes can be queued separately from the driver changes.
* tag 'omap-for-v4.10/pinctrl-cells-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add #pinctrl-cells for pinctrl-single instances
Signed-off-by: Olof Johansson <olof@lixom.net>
The pin controller found in the Allwinner SoCs has support for interrupts
debouncing.
However, this is not done per-pin, preventing us from using the generic
pinconf binding for that, but per irq bank, which, depending on the SoC,
ranges from one to five.
Introduce a device-wide property to deal with this using a microsecond
resolution. We can re-use the per-pin input-debounce property for that, so
let's do it!
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initial pinctrl driver for QCOM msm8994 platforms.
In order to continue the initial board support for QCOM msm8994/msm8992
presented in patches from Jeremy McNicoll <jeremymc@redhat.com>, let's put
a proper pinctrl driver in place.
Currently, the DT for these platforms uses the msm8x74 pinctrl driver to
enable basic UART. Beyond the first few pins the rest are different enough
to justify it's own driver.
Note: This driver is also used by QCOM's msm8992 platform as it's TLM block
is the same.
- Initial formatting and style was taken from the msm8x74 pinctrl driver
added by Björn Andersson <bjorn.andersson@linaro.org>
- Data was then adjusted per QCOM MSM8994v2 documentation for Top Level
Multiplexing
- Bindings documentation was based on qcom,msm8996-pinctrl.txt by
Joonwoo Park <joonwoop@codeaurora.org> and then modified for msm8994
content
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Amlogic Meson GXL SoC, this is a partially complete
definition only based on the Amlogic Vendor tree.
This definition differs a lot from the GXBB and needs a separate entry.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
stm32 pinctrl driver could be probed even if no interrupt controller
is defined to manage gpio irqs. Entries related to gpio irq management
are moved to optional.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for pin output control through the pinctrl config:
- support enabling/disabling output on a given pin
- support output level setting (high or low)
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI1 function was associated with the wrong pins: The functions that
those pins provide is either an SPI debug or passthrough function
coupled to SPI1. Make the SPI1 mux function configure the relevant pins
and associate new SPI1DEBUG and SPI1PASSTHRU functions with the pins
that were already defined.
The notation used in the datasheet's multi-function pin table for the SoC is
often creative: in this case the SYS* signals are enabled by a single bit,
which is nothing unusual on its own, but in this case the bit was also
participating in a multi-bit bitfield and therefore represented multiple
functions. This fact was overlooked in the original patch.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull ARM DT updates from Arnd Bergmann:
"These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably, an
ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been
addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets,
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange Pi Lite,
Olimex A33-Olinuxino, and Nano Pi Neo single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform, Raspberry Pi
Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file),
Armada 395 SoC platform and GP board Armada 390 DB development
board
- NXP i.MX: imx7s Warp7 reference board, Gateworks Ventana GW553x
single-board computer, Technologic Systems TS-4900 and Engicam
IMX6UL GEA M6UL computer-on-module, Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board, Firefly RK3288
Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (390 commits)
ARM: dts: sony-nsz-gs7: add missing unit name to /memory node
ARM: dts: chromecast: add missing unit name to /memory node
ARM: dts: berlin2q-marvell-dmp: add missing unit name to /memory node
ARM: dts: berlin2: Add missing unit name to /soc node
ARM: dts: berlin2cd: Add missing unit name to /soc node
ARM: dts: berlin2q: Add missing unit name to /soc node
ARM: dts: berlin2: Remove skeleton.dtsi inclusion
ARM: dts: berlin2cd: Remove skeleton.dtsi inclusion
ARM: dts: berlin2q: Remove skeleton.dtsi inclusion
arm: dts: berlin2q: enable all wdt nodes unconditionally
arm: dts: berlin2: enable all wdt nodes unconditionally
ARM: dts: omap5-igep0050.dts: Use tabs for indentation
ARM: dts: Fix igepv5 power button GPIO direction
ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
...
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
As far as I'm aware the mv88f5181-b1 and mv88f5181l are the same at the
pinctrl level, so re-use the definitions for both.
[gregory.clement@free-electrons.com: fix commit title]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Outline expectations on the pin controller's relationship with the
System Control Unit (SCU) IP through syscon, and document the compatible
strings for 4th and 5th generation Aspeed SoC pin controllers.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: sh-pfc: Add support for R-Car M3-W
Add initial support for the Pin Function Controller on the Renesas R-Car
M3-W SoC:
- Basic definitions,
- SCIF (serial) pins, groups and functions,
- SDHI pins, groups and functions.
This patch allows to use the second parameter of gpio
specifier, which is used to specify whether the gpio is
active high or low.
Simply remove specific of_xlate callback() and of_gpio_n_cells
and use default one set by of_gpiochip_add() which allows
to use second parameter gpio specifier.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
