Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
The Aspeed SoCs have two BT interfaces : one is IPMI compliant and the
other is H8S/2168 compliant.
The current ipmi/bt-bmc driver implements the IPMI version and we
should reflect its nature in the compatible node name using
'aspeed,ast2400-ibt-bmc' instead of 'aspeed,ast2400-bt-bmc'. The
latter should be used for a H8S interface driver if it is implemented
one day.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove the following outbound related device tree properties:
brcm,pcie-ob-window-size
brcm,pcie-ob-oarr-size
The above two properties are a bit duplicated in functions. In addition,
the next generation iProc PCIe controller has outbound mapping window that
supports more than just two sizes, which cannot be properly supported by
these properties.
[bhelgaas: changelog]
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
This patch adds specific compatible to support all the unversioned SCPI
protocols prior to v1.0 release. This will be applicable for all the
implementations using draft versions or modified versions of those
draft vesrions of SCPI protocol.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Since SCPI is a generic protocol and the bindings are intended to be
generic, we need to decouple all the platform specific binding details
out of the generic bindings.
This patch moves are the Juno platform specific details into a separate
binding document.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Audio block requires access to two parent clocks: audio PLL and oscillator,
so add this information to device tree bindings documentation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The proper parent clock for FSYS block is "aclk_fsys_200"
according to the Exynos5433 reference manual.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The SVG files are larger than the draw dimentions, have long
lines and aren't cleaned. Use inkscape to automatically fix
those issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On some tablets the touchscreen controller is powered by separate
regulators, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Per the original author, the proposed document was never deemed
necessary, and the important bits got merged into completion.txt. Let's
just stop confusing readers by pointing at a nonexistent doc.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is a conversion of the USB documentation to the Sphinx format.
No content was altered or reformatted.
Signed-off-by: Oliver <oneukum@suse.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
While the {READ,WRITE}_ONCE() macros should be used in preference to
ACCESS_ONCE(), the circular buffer documentation uses the latter
exclusively.
To point people in the right direction, and as a step towards the
eventual removal of ACCESS_ONCE(), update the documentation to use
READ_ONCE(), as ACCESS_ONCE() is only used in a reader context in the
circular buffer documentation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
While the {READ,WRITE}_ONCE() macros should be used in preference to
ACCESS_ONCE(), the atomic documentation uses the latter exclusively.
To point people in the right direction, and as a step towards the
eventual removal of ACCESS_ONCE(), update the documentation to use the
{READ,WRITE}_ONCE() macros as appropriate.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Recent Makefile changes added an rm command without the requisite "-f",
leading to warnings if the files do not exist. Make it be quiet again.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The PDF files that contain media images were actually generated
offline from their SVG or PNG source files.
Sphinx can handle PNG sources automatially. So, let's just
drop their PDF counterparts.
For SVG, however, Sphinx doesn't produce the right tags to
use the TexLive SVG support. Also, the SVG support is done via
shell execution, with is not nice.
So, while we don't have any support for SVG inside Sphinx
core or as an extension, move the logic to build them to Makefile,
producing the PDF images on runtime.
NOTE: due to the way Sphinx works, the PDF images should be
generated inside the Kernel source tree, as otherwise Sphinx
won't find it, not obeying what's specified by "O=" makefile
parameter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Right now, media is using two different formats for bitmap
images: GIF and PNG. Let's use just one, to make it simpler when
building with Sphinx.
As PNG is usually better than GIF, let's use it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
SVG images are nicer, as they can easily be scaled. Also, they're
written in text, with makes easier to work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are several missing columns on the size specification,
causing LaTeX to complain on interactive mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
adjustbox doesn't work on longtables. Also, this
causes an error on LaTeX in interactive mode.
So, use, instead, a tiny font.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
PDF build on Kernel 4.9-rc? returns an error with Sphinx 1.3.x
and Sphinx 1.4.x, when trying to solve some cross-references.
The solution is to redefine the \DURole macro.
However, this is redefined too late. Move such redefinition to
LaTeX preamble and bind it to just the Sphinx versions where the
error is known to be present.
Tested by building the documentation on interactive mode:
make PDFLATEX=xelatex -C Documentation/output/./latex
Fixes: e61a39baf7 ("[media] index.rst: Fix LaTeX error in interactive mode on Sphinx 1.4.x")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Another pile of misc:
- Explicit fencing for atomic! Big thanks to Gustavo, Sean, Rob 3x, Brian
and anyone else I've forgotten to make this happen.
- roll out fbdev helper ops to drivers (Stefan Christ)
- last bits of drm_crtc split-up&kerneldoc
- some drm_irq.c crtc functions cleanup
- prepare_fb helper for cma, works correctly with explicit fencing (Marek
Vasut)
- misc small patches all over
* tag 'drm-misc-next-2016-11-16' of git://anongit.freedesktop.org/git/drm-misc: (51 commits)
drm/fence: add out-fences support
drm/fence: add fence timeline to drm_crtc
drm/fence: add in-fences support
drm/bridge: analogix_dp: return error if transfer none byte
drm: drm_irq.h header cleanup
drm/irq: Unexport drm_vblank_on/off
drm/irq: Unexport drm_vblank_count
drm/irq: Make drm_vblank_pre/post_modeset internal
drm/nouveau: Use drm_crtc_vblank_off/on
drm/amdgpu: Use drm_crtc_vblank_on/off for dce6
drm/color: document NULL values and default settings better
drm: Drop externs from drm_crtc.h
drm: Move tile group code into drm_connector.c
drm: Extract drm_mode_config.[hc]
Revert "drm: Add aspect ratio parsing in DRM layer"
Revert "drm: Add and handle new aspect ratios in DRM layer"
drm/print: Move kerneldoc next to definition
drm: Consolidate dumb buffer docs
drm: Clean up kerneldoc for struct drm_driver
drm: Extract drm_drv.h
...
Pull Allwinner clock changes from Maxime Ripard:
The usual patches from us, but most notably the introduction of the A64
clocks unit.
* tag 'sunxi-clk-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi-ng: sun8i-h3: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: sun8i-a23: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: Add A64 clocks
clk: sunxi-ng: Implement minimum for multipliers
clk: sunxi-ng: Add minimums for all the relevant structures and clocks
clk: sunxi-ng: Finish to convert to structures for arguments
clk: sunxi-ng: Remove the use of rational computations
clk: sunxi-ng: Rename the internal structures
clk: sunxi: mod0: improve function-level documentation
This patch adds support for Exynos5433 specific version of the GScaler
module. The main difference between Exynos 5433 and earlier is addition
of new clocks that have to be controlled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_LOG_ADDRS_FL_CDC_ONLY flag is missing at the documentation,
causing this warning:
Documentation/output/cec.h.rst:6: WARNING: undefined label: cec-log-addrs-fl-cdc-only (if the link has no caption the label must precede a section header)
Add a documentation for it, based on the commit that introduced the
flag.
Fixes: a69a168a1b ("[media] cec: add proper support for CDC-Only CEC devices")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The last open issues have been addressed, so it is time to move
this out of staging and into the mainline and to move the public
cec headers to include/uapi/linux.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_MSG_INITIATE_ARC message is special since it is the ONLY
CEC message that accepts two possible valid replies:
CEC_MSG_REPORT_ARC_INITIATED and CEC_MSG_REPORT_ARC_TERMINATED.
So if the transmitted message is CEC_MSG_INITIATE_ARC and the remote
side replied with CEC_MSG_REPORT_ARC_INITIATED or CEC_MSG_REPORT_ARC_TERMINATED,
then a msg->reply value of CEC_MSG_REPORT_ARC_INITIATED or
CEC_MSG_REPORT_ARC_TERMINATED will match either reply.
I thought about either adding a second reply2 field, but that's ugly
for all other messages that have only one reply, and what if in the
future a new message is added that can have three replies?
Another option would be to add a cec_msg flag, but really, the combination
of CEC_MSG_REPORT_ARC_INITIATED and a reply value of one of the two
possible replies already functions as a flag.
Another advantage of this approach is that it is safe to re-use a
cec_msg struct. No need to zero a flags field or a reply2 field.
So since this really is an exception in the CEC specification, I
decided to implement it as an exception as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Give the caller more control over how replies to a transmit are
handled. By default the reply will only go to the filehandle that
called CEC_TRANSMIT. If this new flag is set, then the reply will
also go to all followers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
By default the CEC_MSG_USER_CONTROL_PRESSED/RELEASED messages
are passed on to the follower(s) only. If the new
CEC_LOG_ADDRS_FL_ALLOW_RC_PASSTHRU flag is set in the
flags field of struct cec_log_addrs then these messages are also
passed on to the remote control input subsystem and they will appear
as keystrokes.
This used to be the default behavior, but now you have to explicitly
enable it. This is done to force the caller to think about possible
security issues (e.g. if these messages are used to enter passwords).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This uses Laurent's python script to convert all tables, dropping
the useless 'row' comments.
See commit c2b66cafdf ("[media] v4l: doc: Remove row numbers from tables")
for the script that was used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The code examples on how to enumerate controls were really long in the
tooth. Update them.
Using FLAG_NEXT_CTRL is preferred these days, so give that example first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Improve the internal CEC documentation. In particular add a section
that specifies that transmit-related interrupts should be processed
before receive interrupts.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Jonathan writes:
Third set of IIO new device support, features and cleanup for the 4.10 cycle.
Includes Peter Rosin's interesting drivers for a comparator. First complex
use we have had with an analog front end made from discrete components.
Brian Masney's work on moving the tsl2583 driver out of staging also
feature extensively!
New Drivers
* DAC based on a digital potentiometer
- New driver for the use of a dpot as a DAC. Includes bindings and Axentia
entry in vendor prefixes.
* Envelope detector baed on DAC and a comparator including device tree
bindings.
Staging Graduation
* tsl2583.
Core new features
- Core provision for _available attributes. This one had been stalled for
a long time until Peter picked it up and ran with it!
- In kernel interface helpers to retrieve available info from channels.
Driver new features
* mcp4531
- Add range of available raw values (used for the dpot dac driver).
Driver cleanups and fixes for issues introduced
* ad7766
- Testing the wrong variable following devm_regulator_bulk_get introduced
with the driver earlier in this cycle.
* ad9832
- Fix a wrong ordering in the probe introduced in the previous set of
patches. A use before allocation bug.
* cros_ec_sensors
- Testing for an error in a u8 will never work.
* mpu3050
- Remove duplicate initializer for the module owner.
- Add missing i2c dependency.
- Inform the i2c mux core how it is used - step one in implifying device
tree bindings.
* st-sensors
- Get rid of large number of uninformative defines in favour of putting the
constants where they are relevant. It is clear what they are from where
they are used.
* tsl2583
- Fix unused function warning when CONFIG_PM disabled and remove the
ifdefs in favour of __maybe_unused.
- Refactor taos_chip_on to only read relevant registers.
- Make sure calibscale and integration time are being set.
- Verify chip is in ready to be used before calibration.
- Remove some repeated checks for chip status (it's protected by a mutex
so can't change until it's released)
- Change current state storage from a tristate enum to a boolean seeing as
only two values are actually used now.
- Drop a redundant write to the control regiser in taos_probe (it's a noop)
- Drop the FSF mailing address.
- Clean up logging to not use hard coded function names (use __func__
instead).
- Cleanup up variable and function name prefixes.
- Alignment of #define fixes.
- Fix comparison between signed and unsigned integer warnings.
- Add some newlines in favour of readability.
- Combine the two sysfs ABI docs that somehow ended up in different places.
- Fix multiline comment syntax.
- Move a code block to inside an else statement as it makes more sense there.
- Change tsl2583_als_calibrate to return 0 rather than a value nothing
reads.
- Drop some pointless brackets
- Don't assume 32bit unsigned int.
- Change to a per device instance lux table.
- Add missing tsl2583 to the list of supported devices in the intro comments.
- Improve commment on clearing of interrupts.
- Drop some uninformative comments.
- Drop a memset call that doesn't do anything useful any more.
- Don't initialize some return variables that are always set.
- Add Brian Masney as a module author after all these changes.
