STi DT fix:
Fix typo cs-gpio to cs-gpios
* tag 'sti-dt-for-v4.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH410-b2260: Fix typo in spi0 chipselect definition
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX fixes for 4.9, 2nd round:
It fixes a boot failure on imx53-qsb board with a DA9053 PMIC, which is
caused by the regulator core change, commit fa93fd4ecc ("regulator:
core: Ensure we are at least in bounds for our constraints").
* tag 'imx-fixes-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx53-qsb: Fix regulator constraints
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the GPIO names for the Raspberry Pi Zero. The GPIO lines
of the RPi Zero are almost identical to the Model A+ except:
* GPIO 35, 38, 40 and 45 are not connected
* Status LED is active low
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are some differences between the schematics and the official firmware
DTS [1]. So based on these additional information the following has been
changed:
* use consistent "CAM_GPIO1" for camera LED
* use consistent "CAM_GPIO0" for camera shutdown
* add "USB_LIMIT" for USB current limit (0=600mA, 1=1200mA)
[1] - https://github.com/raspberrypi/firmware/blob/master/extra/dt-blob.dts
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It's BCM4709A0 based device with 16 MiB flash, 128 MiB of RAM and two
PCIe based on-PCB BCM4360 chipsets.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
RK1108 EVB is designed by Rockchip for CVR field.
This patch add basic support for it, which can boot with
initramfs into shell.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK1108 is embedded with an ARM Cortex-A7 single core and a DSP core.
It is designed for varies application scenario such as car DVR, sports
DV, secure camera and UAV camera.
This patch add basic support for it with DMAC / UART / CRU / pinctrl / MMC
enabled.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Jacob Chen <jacob2.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Drop the space before/after '<' and '>'; and
separate the entries to be a bit more readable.
Reported-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: arm-soc
Series-cc: julia@ni.com
The patch removes these warnings reported by dtc 1.4:
Warning (unit_address_vs_reg): Node /pmu has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Julia Cartwright <julia@ni.com>
Series-to: arm-soc
Based on
"ARM: dts: explicitly mark skeleton.dtsi as deprecated"
(sha1: 9c0da3cc61)
skeleton.dtsi is deprecated.
Move address and size-cells directly to zynq-7000.dtsi.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Julia Cartwright <julia@ni.com>
Let's add minimal support for droid 4 with MMC and WLAN working.
It can be booted with appended dtb using kexec to a state where
MMC and WLAN work with currently no support for it's PMIC or
display.
Note that we are currently using fixed regulators as we don't
have support for it's cpcap PMIC. I'll be posting regmap_spi
based minimal cpcap patches later on for USB and the debug
UART on droid 4 multiplexed with the USB connector.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the nodes for the MSTPRI configuration and DDR2/mDDR memory
controller drivers to da850.dtsi.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The STMicrolectornics's STM32F746 MCU has the following main features:
- Cortex-M7 core running up to @216MHz
- 1MB internal flash, 320KBytes internal RAM (+4KB of backup SRAM)
- FMC controller to connect SDRAM, NOR and NAND memories
- Dual mode QSPI
- SD/MMC/SDIO support
- Ethernet controller
- USB OTFG FS & HS controllers
- I2C, SPI, CAN busses support
- Several 16 & 32 bits general purpose timers
- Serial Audio interface
- LCD controller
- HDMI-CEC
- SPDIFRX
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
It is the 10th processor in the well-known imx6 series, and derived
from imx6ul but cost optimized. The more information about imx6ull
can be found at:
http://www.nxp.com/products/microcontrollers-and-processors/
arm-processors/i.mx-applications-processors/i.mx-6-processors
/i.mx6qp/i.mx-6ull-single-core-processor-with-arm-cortex-a7-core
:i.MX6ULL
imx6ul.dtsi is the SoC common stuff for both imx6ul and imx6ull;
imx6ul-14x14-evk.dts is the board common stuff for both imx6ul
and imx6ull 14x14 evk. In this patch, for SoC part, the
imx6ull.dtsi includes imx6ul.dtsi; for board part, imx6ull-14x14-evk.dts
includes imx6ul-14x14-evk.dts.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DDR3L is usually specified as
JEDEC standard 1.35V(1.28V~1.45V) & 1.5V(1.425V~1.575V)
Therefore setting smps6 regulator to 1.2V is definitively below
minimum. It appears that real world chips are more forgiving than
data sheets indicate, but let's set the regulator right.
Note: a board that uses other voltages (DDR with 1.5V) can
overwrite by referencing &smps6_reg.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DMA controller driver is in good shape these days on rockchip platforms.
So lets enable DMA for uart and mmc.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As explained by commit 9c0da3cc61 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It turns out that the i2c1 adapter is connected to a multiplexer
controlled by a gpio line. The first (default) mux option connects
i2c1 to a bus connected to the already known peripherals. The other
one connects the adapter to the ddc pins of the DVI port.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the schematics of CompuLab's sbc-fx6 baseboard and the
vendor devicetree GPIO_16 is *not* muxed to ENET_REF_CLK but to SPDIF_IN.
Remove the wrong pinctrl setting.
Fixes: 682d055e6a ("ARM: dts: Add initial support for cm-fx6.")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The UART pinmux defines for the pins which are part of the LPSR
pinmux controller are wrong: Output signals configure the input
sel value and the pinmux defines allow not to distinguish between
DCE/DTE mode. Follow the usual pattern using DTE/DCE as part of
the define to denote the two UART configuration options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6QP the LDB clock tree has changed to move the clk gate
before the divider, to prevent clock glitches propagating downstream.
A consequence of this change is that the clk divider is now the
parent of the LDB inputs. Reflect this change in the devicetree
to allow the LDB driver to properly configure the display clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
MMDC has a slightly different programming model between imx6q and imx6qp
in terms of perf support, it's exactly same for suspend support, so we
have fsl,imx6q-mmdc here to save patching suspend driver with the new
compatible.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board is now manufactured by Aries Embedded GmbH, update compat string.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board is now manufactured by Aries Embedded GmbH, update compat string.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The idea is to give useful names to GPIO lines that an implementer
will be using from userspace, e.g. for maker type projects. These are
user-visible using tools/gpio/lsgpio.c
v2: Major rewrite by anholt: Flatten each GPIO line to a line in the
file for better diffing, prefix all expansion header pins with
"P<number>" or "P5HEADER_P<number>" and drop the mostly-unused
GPIO_GEN<smallnumber> names in favor of GPIO<socgpionumber>, fix
extra '[]' on a couple of lines, fix locations of SD_CARD_DETECT,
CAM_GPIO and STATUS_LED, fix HDMI_HPD polarities, rewrite A+ using
unreleased schematics.
v3: More changes by anholt: Drop P<number> / P5HEADER<number>
prefixes. I had been skeptical about adding them, and was
convinced to drop them by Gottfried (who probably has more
experience with GPIOs in educational contexts than the rest of
us). Also drop [] brackets for "is pinmuxed", which didn't seem
to clarify, and were ambiguous for things like the SPI_*-labeled
pins which may or may not actually be pinmuxed to SPI.
v4: Rename B+'s SDA0/SCL0 to match the other boards, despite the
naming on its schematic.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the node for the thermal sensor of the bcm2835-soc
to the device tree.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Changelog:
V1 -> V5: generic settings is shared in bcm283x.dtsi, but disabled
moved the compatible string to the SOC specific dtsi
for arm and arm64
V5 -> V6: fix remove 0x prefix from thermal@0x7e212000
Note: there is no arm/boot/dts/bcm2837.dtsi as of now,
so the 32-bit rpi3 dt is not modified.
Signed-off-by: Eric Anholt <eric@anholt.net>
We used to use a fixed rate clock for the UARTs. Now that we have clock
support we can associate the correct clocks to the UARTs and drop the
26MHz fixed rate UART clock.
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clock controller nodes for MT2701, include topckgen, infracfg,
pericfg and apmixedsys. This patch also add two oscillators that
provide clocks for MT2701.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Rename sound card to differentiate B2120 and B2260 sound card.
Sound card name is used by alsa-lib to load associated card
configuration file.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Lots of platforms contain clocks which if turned off would prove fatal.
The only way to recover is to restart the board(s). This driver takes
references to clocks which are required to be always-on. The Common
Clk Framework will then take references to them. This way they will
not be turned off during the clk_disabled_unused() procedure.
In this patch we are identifying clocks, which if gated would render
the STiH407 development board unserviceable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
The DRA718-evm is a board based on TI's DRA718 processor targeting
BOM-optimized entry infotainment systems and is a reduced pin and
software compatible derivative of the DRA72 ES2.0 processor.
This platform features:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- uSD
- 8GB eMMC
- CAN
- PCIe
- USB3.0
- Video Input Port
- LP873x PMIC
More information can be found here[1].
Adding support for this board while reusing the data available in
dra72-evm-common.dtsi.
[1] http://www.ti.com/product/dra718
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra72-evm-common.dtsi consolidates dra72-evm.dts and dra72-evm-revc.dts
which also include tps65917 pmic support as both the evms uses the same
pmic. But, dra71-evm has mostly similar features with a different pmic.
In order to exploit dra72-evm-common.dtsi, creating a separate dtsi
for tps65915 support and including it in respective board files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
