Almost all sun8i tablets use a gsl1680 touchscreen controller, so add
a node describing it to reference-design-tablet.dtsi.
Almost all, but not all, so mark it as disabled by default (dts files
will also need to supply a firmware-name and resolution info).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ga10h tablet has a rtl8703as wifi chip, add a dt node describing it.
This enables usage of wifi on this tablet (together with the out of
tree rtl8732bs driver).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This results in quite a nice cleanup for this dts file.
As an added bonus this also enables full otg support. I've tested that
this works as advertised.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CHIP has a status LED connected to one of the AXP GPIOs. Add the
gpio-leds node to be able to use the proper LED framework to control it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the general purpose software switches SW2 and tactile
switches SW24/25 as a virtual keyboard (like it was done with the Lager/
Koelsch boards).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LCDK embeds a TLV320AIC3106 connected to the SoC McASP for analog
audio. The power supply of the codec comes from the main PMIC
(TPS650250) DCDCs which are always on per HW design and not
controllable by SW, so SW wise the codec driver will rely on the 'dummy'
regulator.
Quality is good with arecord -pipe- aplay on Line In/Line Out.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The "linux,stdout-path" is deprecated.
Add serial options so the console can be properly configured when
bootloader does not pass "console" parameter to the command line. Without
options and lack of "console" in command line, the serial output dies
during boot (just after probing sound, probably because of rate change).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
There are many regulators are missed in previous commit, this
commit complete most of them. It also fix some mistakes in the
regulator properties. The VDD_10(REG10) and VCC_18(REG11) had better
to keep in always-on state, as it is used as the USB PHY supply,
corretly we have no way to assign power supply to a USB PHY.
The VCCA_33(REG8) should be enabled or the GMAC won't work.
It also fix the wrong properties for audio in io-domains, the supply
connected to APIO4_VDD is different to firefly release version.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Because of a bug in hardware design, the sdcard at firefly
rk3288 reload board can't switch the io voltage level to 1.8v.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently the davinci da8xx boards use the mach-davinci aemif code.
Instantiating an aemif node into the DT allows to use the ti-aemif
memory driver and is another step to better DT support.
This change adds an aemif node in the dtsi while retiring the nand_cs3
node. The NAND is now instantiated in the dts as a subnode of the aemif
one along with its pins.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
imx7s-warpd has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Warp7 has a BCM43430 Wifi chip connected to the USDHC1 port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only i.MX 7Dual SoC supports CPU frequencies of up to 1GHz. The i.MX
7Solo can run with up to 800MHz and does so without making use of DVFS
usually. While the device tree clearly specified a too fast operating
point for i.MX 7Solo, the kernel did not used it in practise so far
because the CPUfreq driver does not get loaded on i.MX 7Solo devices
(since the fsl,imx7s compatible string is not in the list of devices
making use of the cpufreq-dt driver...).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As of commit 5aa2eb3c86 ("[media] v4l: vsp1: Configure device
based on IP version"), the DT properties to identify the exact VSP
device instance features are no longer used. Hence remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 5aa2eb3c86 ("[media] v4l: vsp1: Configure device
based on IP version"), the DT properties to identify the exact VSP
device instance features are no longer used. Hence remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Alt board dependent part of the MMCIF device node.
Like the Silk the board has eMMC chip along with the necessary voltage
regulator (note that the Vcc/Vccq regulator is dummy -- it's required by
the MMCIF driver but doesn't actually exist on the board).
Based on work for the Silk board by Vladimir Barinov and Sergei Shtylyov.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Alt board dependent part of the SDHI0 and 1
device nodes along with the necessary voltage regulators.
Based on work by the original patch by Vladimir Barinov and
Sergei Shtylyov for the Silk board.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ARM GIC only supports interrupts with either level-high or
rising-edge types for SPIs. The interrupt type for the Palmas PMIC used
for Tegra114 boards is specified as level-low which is invalid for the
GIC. This has gone undetected because until recently, failures to set
the interrupt type when the interrupts are mapped via firmware (such as
device-tree) have not been reported. Since commits 4b357daed6
("genirq: Look-up trigger type if not specified by caller") and
1e2a7d7849 ("irqdomain: Don't set type when mapping an IRQ"), failure
to set the interrupt type will cause the requesting of the interrupt to
fail and exposing incorrectly configured interrupts.
Please note that although the interrupt type was never being set for the
Palmas PMIC, it was still working fine, because the default type setting
for the interrupt, 'level-high', happen to match the correct type for
the interrupt.
Finally, it should be noted that the Palmas interrupt from the PMIC is
actually 'level-low', however, this interrupt signal is inverted by the
Tegra PMC and so the GIC actually sees a 'level-high' interrupt which is
what should be specified in the device-tree interrupt specifier.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
DT compatible values should always include an entry for the specific
chip in addition to any earlier generations that the HW is backwards-
compatible with.
This doesn't affect the kernel at all given current driver code, but
U-Boot needs to distinguish between Tegra114 and Tegra30 for this HW,
and I'd like to synchronize the DT content.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /gpio_keys/button0@10 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /gpio_keys/button0@10 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /matrix_keypad@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit b8d368caa8 ("ARM: dts: omap3: overo: remove unneded unit names
in display nodes") removed the unit names for all Overo display nodes
that didn't have a reg property.
But the display in arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi does
have a reg property so the correct fix was to make the unit name match
the value of the reg property, instead of removing it.
This patch fixes the following DTC warning for boards using this dtsi:
"ocp/spi@48098000/display has a reg or ranges property, but no unit name"
Fixes: b8d368caa8 ("ARM: dts: omap3: overo: remove unneded unit names in display nodes")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /ocp has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fix was applied to a bunch of omap3 devices including LogicPD
Torpedo, but this got missed since it was new around the same times
the patches were applied. This makes the GPMC parameters match the
Torpedo since they have the same processor PoP memory.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This was applied to a variety of omap3 boards, so it should
probably be applied here. I did not test NAND performance, but
I tested this with UBI to confirm read/write didn't break.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The gpmc ranges property for NAND at CS0 was being overridden by later
includes that defined gpmc ethernet nodes, effectively breaking NAND on
these systems:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
Instead of redefining the NAND range in every such dtsi, define all
currently used ranges in omap3-overo-base.dtsi.
Fixes: 98ce6007ef ("ARM: dts: overo: Support PoP NAND")
Cc: stable <stable@vger.kernel.org> # 4.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The gpmc ranges property for NAND at CS0 has been broken since it was
first added.
This currently prevents the nand gpmc child node from being probed:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
and consequently the NAND device from being registered.
Fixes: 98ce6007ef ("ARM: dts: overo: Support PoP NAND")
Cc: stable <stable@vger.kernel.org> # 4.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The check for the "elm_id" binding had been removed.
This causes nand boot to fail on boards still using
the old binding. Update the bindings on those boards.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for MPL3115 NXP pressure sensor.
Tested by reading temperature and pressure:
$ cat /sys/bus/iio/devices/iio:device0/in_temp_raw
$ cat /sys/bus/iio/devices/iio:device0/in_pressure_raw
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* small form factor (35x70mm)
* 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
* 256MB NAND flash (4GB option)
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* 1x miniPCI socket (with PCIe, USB, SIM)
* 1x microSD socket
* 1x SIM socket
* Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
* analog CVBS video in
* GPS (optional uBlox EVA-M8M)
* Application headers:
- 2x TTL UART (TX/RX)
- 4x TTL GPIO (3x configurable as PWM)
- 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
* Front panel connectors:
- micro-HDMI audio/video out
- 1x user programmable LED
- 1x configurable user pushbutton
- 1x USB OTG
See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7 as a GICv2, hence its CPU interface register map (the
second register region) is 8kB long. Add the VGIC maintenance
interrupt which allows to use the new VGIC driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
