The socfpga_cyclone5.dtsi is included by all DTS files which describe boards
using the Cyclone V SoC. The Cyclone V SoC has two ethernet controllers and
different boards use none, one or both of them.
The /soc/ethernet@ff702000/{} node in socfpga_cyclone5.dtsi unconditionaly
enabled gmac0 interface, which is clearly wrong for those boards which use
gmac1 interface instead.
This patch removes the entire /soc/ethernet@ff702000/{} node from the
socfpga_cyclone5.dtsi file. This is correct, since all of the board which
include this file also have correct gmac0 or gmac1 node present in them.
Minor correction had to be done to EBV SoCrates, which didn't define PHY
mode explicitly, but inherited it from the socfpga_cyclone5.dtsi .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The phy-addr property of stmmac is deprecated and the stmmac driver
does not use it either. On the contrary, the driver will warn if
this property is defined. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The PL330 DMA driver will not load on Arria10 without devicetree entries
for clocks and clock_names. This patch adds those entries. It also adds
the ninth interrupt, which is required for error detection.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for OMAP5 clock nodes:
Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for DRA7 clock nodes:
Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for DM81x clock nodes:
Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for AM43xx clock nodes:
Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for AM33xx clock nodes:
Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for OMAP4 clock nodes:
Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for OMAP2 clock nodes:
Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming change to DT compiler is going to complain about nodes
which have a reg property, but have not defined the address in their
name. This patch fixes following type of warnings for OMAP3 clock nodes:
Warning (unit_address_vs_reg): Node /ocp/cm@48004000/clocks/dpll3_m2_ck
has a reg or ranges property, but no unit name
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"bandgap has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warning:
"sound@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"pmu has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"i2c@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"pbias_regulator has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CIU clock for the SD/MMC should be the sdmmc_clk and not the
sdmmc_free_clk. Also, add the correct phase shift the sdmmc_clk.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is w.r.t J6/J6eco: 32clk is pseudo (erratum i856) - clock source.
Errata i856 for the AM572x (DRA7xx) points out that the 32.768KHz external
crystal is not enabled at power up. Instead the CPU falls back to using
an emulation for the 32KHz clock which is SYSCLK1/610. SYSCLK1 is usually
20MHz on boards so far (which gives an emulated frequency of 32.786KHz)
Modelling the same in device tree.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The amount of available memory is clearly a board-specific value, so
the core per-soc dtsi should not define a default of any sort.
Therefore move the memory-nodes to the two board files.
Also fix the amount of memory on Kylin (512MB instead of 1GB).
While in most cases the bootloader will override this with the
actual amount of memory, there is no need to keep known wrong values
in the board-dts.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
After hooking up panel and backlight informations, enable the
edp on veyron chromebooks now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Jerry and Speedy don't need any special handling wrt the backlight or
panel, so only need their backlight and panel-regulators hooked up.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Pinky boards don't have the hotplug pin connected. So remove the
hotplug pinctrl setting and enable the force-hpd option, to allow
them to find the display too.
While on speedy boards, the hotplug pin is connected, judging by comments
in a chromeos change it seems the "panels HPD voltage is too low to be
detected", so it also needs the forced hotplug, as we of course also know
that a display is connected.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
The pwm for Minnie's backlight needs to be above 1%, so adapt the start
of non-zero brightness accordingly. Minnie is also using a different
panel, so re-set the compatible property.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
The panel which jaq uses requires the pwm duty cycle larger than 3%,
when the backlight status from power off to power on, otherwise the
backlight will flush, so we modify the second brightness-level to 8,
and when the backlight from power off to power on the pwm duty cycle
will larger than 3%.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Many Veyron chromebooks share the same panel type, so define the core
settings for all of them and allow the few runaways to override it later.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
The panels need a bit of time to actually turn on. If this isn't
observed, this results in problems when trying talk to the panels
and thus produces detection errors. 100ms seem to be a safe value
for the time being.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
The edp hotplug pin is fixed on the soc side, anybody wanting to use it
will need the same definition anyway, so move it to a common location.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Add the rk3288 edp node and its hooks into the display-subsystem.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
Add the core device node of the edp-phy on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Douglas Anderson <dianders@chromium.org>
The cpu_leakage efuse on rk3288 did get it right including the
unitname but on both rk3066a and rk3188 it was missing, fix that.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
The mipi controller node does contain an unused reg property as well as
unnecessary #address-cells and #size-cells properties for subnodes
not using addresses, so remove those to also make dtc happy.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Drop superfluous #address-cells and #size-cells, rename
key-nodes to individual names and also use the key constants
intead of numbers.
Reported-by: Julien Chauveau <chauveau.julien@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
The usbphy subnodes do have a reg property but no unitname, add them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
The power-domain sub-nodes do have reg properties, but so far are
missing the expected unit names. So add the missing ones.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
In Cygnus SOC touch screen controller registers are shared with ADC and
flex timer. Using readl/writel could lead to race condition. So touch
screen driver is enhanced to support register access using syscon framework
API's to take care of mutually exclusive access.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This pull request want to land the analogix_dp driver into drm/bridge directory,
which reused the Exynos DP code, and add Rockchip DP support. And those
patches have been:
* 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux:
drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time
drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time
drm: bridge: analogix/dp: add edid modes parse in get_modes method
drm: bridge: analogix/dp: move hpd detect to connector detect function
drm: bridge: analogix/dp: try force hpd after plug in lookup failed
drm: bridge: analogix/dp: add max link rate and lane count limit for RK3288
drm: bridge: analogix/dp: add some rk3288 special registers setting
dt-bindings: add document for rockchip variant of analogix_dp
drm: rockchip: dp: add rockchip platform dp driver
ARM: dts: exynos/dp: remove some properties that deprecated by analogix_dp driver
dt-bindings: add document for analogix display port driver
drm: bridge: analogix/dp: dynamic parse sync_pol & interlace & dynamic_range
drm: bridge: analogix/dp: remove duplicate configuration of link rate and link count
drm: bridge: analogix/dp: fix some obvious code style
drm: bridge: analogix/dp: rename register constants
drm/exynos: dp: rename implementation specific driver part
drm: bridge: analogix/dp: split exynos dp driver to bridge directory
After exynos_dp have been split the common IP code into analogix_dp driver,
the analogix_dp driver have deprecated some Samsung platform properties which
could be dynamically parsed from EDID/MODE/DPCD message, so this is an update
for Exynos DTS file for dp-controller.
Beside the backward compatibility is fully preserved, so there are no
bisectability break that make this change in a separate patch.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Fix the following warnings from dtc by either adding or removing
the unit name from the node.
Warning (unit_address_vs_reg): Node /soc/flash-controller@40003000/flash@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /pca_buttons/button@7 has a unit name, but no reg property
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Fix the following warnings from dtc by either adding or removing
the unit name from the node.
Warning (unit_address_vs_reg): Node /soc/flash-controller@40003000/flash@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /gpio_joystick/button@4 has a unit name, but no reg property
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
DT nodes without reg properties should not have a unit address. This
fixes the following warnings from dtc.
Warning (unit_address_vs_reg): Node /soc/syscon@40043000/phy@004 has a
unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/syscon@40043000/dma-mux@11c has
a unit name, but no reg property
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add unit name to nvic to remove the following warning:
Warning (unit_address_vs_reg): Node /nv-interrupt-controller has a reg or ranges property, but no unit name
Also correct the node name to 'interrupt-controller'
while changing the line.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Stefan Agner <stefan@agner.ch>
This adds a devicetree for the ARM RealView PBA8 platform,
also known as HBI-0178, "RealView Platform Baseboard for
Cortex-A8" and PBX-A9 "RealView Platform Baseboard
Explore for Cortex-A9"
Tested in QEMU with -M realview-pb-a8, as well as with
-M realview-pbx-a9 -smp cpus=2
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ARM RealView Evaluation Baseboards are basically these:
- The original ARMv5 EB board with an ARM926EJ-S, ARM1136 or
ARM1176 core tile here described in arm-realview-eb.dts
no matter which of these core tiles is being used. This
can be emulated by QEMU "realview-eb" machine, which by
default will have the ARM926EJ-S core tile.
- The same board with one of three MPCore Core tiles:
ARM11MPCore, not to be confused with the similar ARM
PB11MPCore ARM11MPCore test system. This exist in
two revisions:
- Revision A modeled in arm-realview-eb-11mp.dts
- Revision B modeled arm-realview-eb-11mp-revb.dts
Revision B can be emulated by the QEMU
"realview-eb-mpcore" machine, but to match the hardware
also the argument -smp cpus=4 must be passed so that
it has four CPU cores, like the hardware.
There is also evidently from the code in the kernel a
Cortex-A9 core tile for the EB, and this is modeled in
arm-realview-eb-a9mp.dts based on the kernel boardfile.
I have not found a user guide for this EB core tile on
the ARM website and it seems uncommon. It is however
included for completeness.
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
